"ping: archlinux.org: Temporary failure in name resolution" in VB

Shune · 2020-02-06 23:50:45

Hi guys,
I have installed a fresh Arch Linux base in Oracle VM Virtual Box, the ping was working, everything fine and suddenly it stops to ping archlinux.org and google.com
I've made a clone in case I screw something but even the clon can't connect.
I'm going to post some useful material in case someone wants to help me (please help me )

# ping google.com
ping: archlinux.org: Temporary failure in name resolution

# ping 127.0.0.1
6 recived/ 0% lost

/etc/resolv.conf is empty.
Appear [ File '/etc/resolv.conf' is unwritable ] in the end of the text (I'm using nano).

# ip link
# ip address
# lspci -k

# ip link
1: lo: <LOOPBACK, UP, LOWER UP> mtu 65536 disc noqueue state UNKNOWN mode DEFAULT group default glen
1000
link loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: empos3: <BROADCAST, MULTICAST> mtu 1500 disc noop state DOWN mode DEFAULT group default qlen 1000
link/ether 08:00:27:67:dd to brd ff:ff:ff: ff:ff
[root@XXX # ip address
1: lo: <LOOPBACK, UP, LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default q len 1000
link loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred ift forever
inet6 ::1/128 scope host
valid_1ft forever preferred ift forever

2: empos3: <BROADCAST, MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000

link/ether 08:00:27:67:dd: fo brd ff:ff:ff:ff:ff:ff
[root@XXX # lspci -k
00:00.0 Host bridge: Intel Corporation 440FX - 82441FX PMC INatoma] (rev 02)

Kernel modules: intel_agp
00:01.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II]
00:01.1 IDE interface: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II]

Kernel driver in use: ata_piix

Kernel modules: ata_piix, pata_acpi, ata_generic
00:02.0 VGA compatible controller: VMware SVGA II Adapter

Subsystem: VMware SVGA II Adapter
Kernel driver in use: umwgfx
Kernel modules: umwgfx

00:03.0 Ethernet controller: Intel Corporation 82540EM Gigabit Ethernet Controller (rev 02)

Subsystem: Intel Corporation PRO/1000 MT Desktop Adapter
Kernel driver in use: e1000

Kernel modules: e1000
00:04.0 System peripheral: InnoTek Systenberatung GmbH VirtualBox Guest Service

Kernel driver in use: vboxguest
Kernel modules: vboxguest

00:05.0 Multimedia audio controller: Intel Corporation 82801AA AC'97 Audio Controller (reu 01)

Subsystem: Dell 82801AA Ac97 Audio Controller
Kernel driver in use: snd_intel8x0
Kernel modules: snd_inte18x0

00:06.0 USB controller: Apple Inc. KeyLargo/Intrepid USB
Kernel driver in use: ohci-pci
Kernel modules: ohci_pci

Kernel driver in use: piix4_smbus
00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI Creu 08)

Kernel modules: i2c_piix4
00:0b.0 USB controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller

Kernel driver in use: ehci-pci
Kernel modules: ehci_pci
post corporation
reu 02)
00:00.0 SATA controller: Intel Corporation 82801HM/HEM (ICHOM/ICH8M-E) SATA Controller [AHCI model (
Kernel driver in use: ahci
Kernel modules: ahci

What i can do? Do you see something wrong??

Last edited by Shune (2020-02-07 09:29:38)

sammiev · 2020-02-07 00:32:30

Did you create the /etc/hostname file?
and Add matching entries to hosts?

See "Network configuration" in the arch wiki installation guide.

seth · 2020-02-07 07:50:21

Welcome to the forum.
Please use code tags, not quote tags for shell I/O and file contents.

Your NIC isn't up and doesn't have an IP - that's before any routing, resolver or hostname issues.

https://wiki.archlinux.org/index.php/In … l_packages
Which network managing service did you install & enable?

systemctl list-unit-files --state=enabled

dhcpcd should do.

Shune · 2020-02-07 09:39:58

sammiev wrote:

Did you create the /etc/hostname file?
and Add matching entries to hosts?
See "Network configuration" in the arch wiki installation guide.

Yes I did at the beginning and check after again.

nano /etc/hostname
hostname

nano /etc/hosts
127.0.0.1 localehost
::1 localehost
127.0.1.1 hostname.localdomain hostname

The Network tutorial isn't clear enough for my case.

progandy · 2020-02-07 10:12:06

Again:

seth wrote:

Which network managing service did you install & enable?
systemctl list-unit-files --state=enabled

If you do not have started any network service, then you should do so.

dhcpcd should do.

Even systemd-networkd should do if you did not install dhcpcd. (just create a file for wired dhcp, and enable and start the two services)
https://wiki.archlinux.org/index.php/Systemd-networkd

Lone_Wolf · 2020-02-07 11:17:05

nano /etc/hostname
hostname

The contents of /etc/hostname are supposed to be a unique name that can be used to identify the machine on networks.
Maybe you could use something like vbox1 instead of hostname ?

Shune · 2020-02-07 11:23:30

Lone_Wolf wrote:

nano /etc/hostname
hostname
The contents of /etc/hostname are supposed to be a unique name that can be used to identify the machine on networks.
Maybe you could use something like vbox1 instead of hostname ?

For privacy I replaced the hostname. In the file it's a unique name.

Lone_Wolf · 2020-02-07 11:50:43

Understood, please mention that next time you post it.

Arch Linux

#1 2020-02-06 23:50:45

"ping: archlinux.org: Temporary failure in name resolution" in VB

#2 2020-02-07 00:32:30

Re: "ping: archlinux.org: Temporary failure in name resolution" in VB

#3 2020-02-07 07:50:21

Re: "ping: archlinux.org: Temporary failure in name resolution" in VB

#4 2020-02-07 09:39:58

Re: "ping: archlinux.org: Temporary failure in name resolution" in VB

#5 2020-02-07 10:12:06

Re: "ping: archlinux.org: Temporary failure in name resolution" in VB

#6 2020-02-07 11:17:05

Re: "ping: archlinux.org: Temporary failure in name resolution" in VB

#7 2020-02-07 11:23:30

Re: "ping: archlinux.org: Temporary failure in name resolution" in VB

#8 2020-02-07 11:50:43

Re: "ping: archlinux.org: Temporary failure in name resolution" in VB

Board footer