You are not logged in.
Hello.
I've a Conceptronic C54Ri wireless card. The driver is rt61.
I follow the guide from the wiki to install ndiswrapper and wpa.
Installation process is correct but when system start the wireless don't works.
iwconfig out is:
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:off/any
Mode:Auto Frequency:2.462 GHz Access Point: Not-Associated
Bit Rate:54 Mb/s Tx-Power:20 dBm Sensitivity=-121 dBm
RTS thr=2347 B Fragment thr=2346 B
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
sit0 no wireless extensions.
if i run wpa_supplicant in command line the results are:
wpa_supplicant -c /etc/wpa_piso.conf -i wlan0 -Dwext
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
CTRL-EVENT-TERMINATING - signal 2 received
wpa_supplicant -c /etc/wpa_piso.conf -i wlan0 -Dndiswrapper
Trying to associate with 00:60:b3:d5:c3:63 (SSID='Candelaria' freq=2462 MHz)
Association request to the driver failed
Authentication with 00:00:00:00:00:00 timed out.
Trying to associate with 00:60:b3:d5:c3:63 (SSID='Candelaria' freq=2462 MHz)
Association request to the driver failed
Authentication with 00:00:00:00:00:00 timed out.
Trying to associate with 00:60:b3:d5:c3:63 (SSID='Candelaria' freq=2462 MHz)
Association request to the driver failed
Authentication with 00:00:00:00:00:00 timed out.
Trying to associate with 00:60:b3:d5:c3:63 (SSID='Candelaria' freq=2462 MHz)
Association request to the driver failed
CTRL-EVENT-TERMINATING - signal 2 received
Failed to disable WPA in the driver.
My wpa_piso.conf is:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
eapol_version=1
ap_scan=1
fast_reauth=1
network={
ssid="Candelaria"
psk="qwertyuiopasd"
key_mgmt=WPA-PSK
proto=WPA
pairwise=TKIP
group=TKIP
}
What's the problem?
How can i fix it?
Have anybody C54Ri works?
Thanks!
Offline
psk="qwertyuiopasd"
Just checking, you have a passkey (psk) which consists of numbers and chars, like psk="53782jha894yahu77891" something .. Which is the generated response you get from inserting essid+passphrase into wpa_passphrase?
Offline
I think that is not the problem.
I try with laptop and ipw2100 with the same wpa configuration file (and same wpa) and it's works well.
If i run wpa_supplicant -c /etc/wpa_piso.conf -i wlan0 -Dwext
The card connect and disconnect constant:
[root@Pilli ~]# wpa_supplicant -c /etc/wpa_piso.conf -i wlan0 -Dwext
Trying to associate with 00:60:b3:d5:c3:63 (SSID='Candelaria' freq=2462 MHz)
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
Associated with 00:60:b3:d5:c3:63
CTRL-EVENT-TERMINATING - signal 2 received
Before abort with ctrl + c, in another terminal i can see:
[root@Pilli ~]# iwconfig
lo no wireless extensions.eth0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:off/any
Mode:Auto Frequency:2.462 GHz Access Point: Not-Associated
Bit Rate:48 Mb/s Tx-Power:20 dBm Sensitivity=-121 dBm
RTS thr=2347 B Fragment thr=2346 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-66 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0sit0 no wireless extensions.
[root@Pilli ~]# iwconfig
lo no wireless extensions.eth0 no wireless extensions.
wlan0 IEEE 802.11g ESSID:"Candelaria"
Mode:Managed Frequency:2.462 GHz Access Point: 00:60:B3:D5:C3:63
Bit Rate=54 Mb/s Tx-Power:20 dBm Sensitivity=-121 dBm
RTS thr=2347 B Fragment thr=2346 B
Encryption key:off
Power Management:off
Link Quality:100/100 Signal level:-66 dBm Noise level:-256 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0sit0 no wireless extensions.
This repeats constant.
Why the card connect and disconnect the AP?
Thanks
Offline