Arch Linux

trapanator

Member

From: Italy

Registered: 2009-08-10

Posts: 151

Booting the ArchLinux installer from usb doesn't detect internal eMMC

Hello,

I am trying to install Archlinux on my Minix Z64. It's a Intel Baytrail device with 32GB eMMC inside.

To run the Installer USB disk I have to pass the "acpi=off" to grub boot parameter or I cannot see anything on the screen.

But when it booted, I cannot see the eMMC drive (/dev/mmc0...) and the fdisk -l lists only the USB and loop devices.

How can I do?

Thank you!

trapanator

Member

From: Italy

Registered: 2009-08-10

Posts: 151

Re: Booting the ArchLinux installer from usb doesn't detect internal eMMC

I am seeing that these kernel modules are not loaded at startup:

mmc_block
sdhci
sdhci_acpi

But on the installation shell, if I modprobe them, I cannot still see the eMMC drive on /dev/mmc...

Lone_Wolf

Member

From: Netherlands, Europe

Registered: 2005-10-04

Posts: 11,911

Re: Booting the ArchLinux installer from usb doesn't detect internal eMMC

looks like you created a bugreport for it , https://bugs.archlinux.org/task/73231

Does lsblk show it ?

---

Disliking systemd intensely, but not satisfied with alternatives so focusing on taming systemd.

(A works at time B)  && (time C > time B ) ≠  (A works at time C)

trapanator

Member

From: Italy

Registered: 2009-08-10

Posts: 151

Re: Booting the ArchLinux installer from usb doesn't detect internal eMMC

lsblk

NAME   MAJ:MIN RM   SIZE RO TYPE MOUNTPOINTS
loop0    7:0    0 715.4M  1 loop /run/archiso/airootfs
sda      8:0    1  14.4G  0 disk 
├─sda1   8:1    1   790M  0 part /run/archiso/bootmnt
└─sda2   8:2    1    74M  0 part 

dmesg

[    0.000000] microcode: microcode updated early to revision 0x838, date = 2019-04-22
[    0.000000] Linux version 5.15.12-arch1-1 (linux@archlinux) (gcc (GCC) 11.1.0, GNU ld (GNU Binutils) 2.36.1) #1 SMP PREEMPT Wed, 29 Dec 2021 12:04:56 +0000
[    0.000000] Command line: initrd=\arch\boot\intel-ucode.img initrd=\arch\boot\amd-ucode.img initrd=\arch\boot\x86_64\initramfs-linux.img archisobasedir=arch archisolabel=ARCH_202201 acpi=off
[    0.000000] x86/fpu: x87 FPU will use FXSAVE
[    0.000000] signal: max sigframe size: 1440
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000008efff] usable
[    0.000000] BIOS-e820: [mem 0x000000000008f000-0x000000000008ffff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x0000000000090000-0x000000000009dfff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009e000-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000001fffffff] usable
[    0.000000] BIOS-e820: [mem 0x0000000020000000-0x00000000201fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000020200000-0x0000000079bbcfff] usable
[    0.000000] BIOS-e820: [mem 0x0000000079bbd000-0x000000007c3c2fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007c3c3000-0x000000007c3f2fff] ACPI data
[    0.000000] BIOS-e820: [mem 0x000000007c3f3000-0x000000007c4a6fff] ACPI NVS
[    0.000000] BIOS-e820: [mem 0x000000007c4a7000-0x000000007c754fff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007c755000-0x000000007c75efff] usable
[    0.000000] BIOS-e820: [mem 0x000000007c75f000-0x000000007c75ffff] reserved
[    0.000000] BIOS-e820: [mem 0x000000007c760000-0x000000007ccfffff] usable
[    0.000000] BIOS-e820: [mem 0x00000000e00f8000-0x00000000e00f8fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed01000-0x00000000fed01fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed08000-0x00000000fed08fff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000ffc80000-0x00000000ffffffff] reserved
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] efi: EFI v2.31 by American Megatrends
[    0.000000] efi: ESRT=0x7c3c2000 ACPI=0x7c3f2000 ACPI 2.0=0x7c3f2014 SMBIOS=0x7c709018 
[    0.000000] SMBIOS 2.7 present.
[    0.000000] DMI: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 11/27/2014
[    0.000000] tsc: Detected 1333.333 MHz processor
[    0.000025] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[    0.000040] e820: remove [mem 0x000a0000-0x000fffff] usable
[    0.000061] last_pfn = 0x7cd00 max_arch_pfn = 0x400000000
[    0.000123] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.000422] total RAM covered: 1997M
[    0.001001] Found optimal setting for mtrr clean up
[    0.001004]  gran_size: 64K 	chunk_size: 64M 	num_reg: 5  	lose cover RAM: 0G
[    0.011199] esrt: ESRT header is not in the memory map.
[    0.013578] Secure boot disabled
[    0.013583] RAMDISK: [mem 0x7278b000-0x764c6fff]
[    0.013669] No NUMA configuration found
[    0.013673] Faking a node at [mem 0x0000000000000000-0x000000007ccfffff]
[    0.013684] NODE_DATA(0) allocated [mem 0x79a02000-0x79a05fff]
[    0.013752] Zone ranges:
[    0.013756]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.013765]   DMA32    [mem 0x0000000001000000-0x000000007ccfffff]
[    0.013772]   Normal   empty
[    0.013777]   Device   empty
[    0.013782] Movable zone start for each node
[    0.013785] Early memory node ranges
[    0.013787]   node   0: [mem 0x0000000000001000-0x000000000008efff]
[    0.013793]   node   0: [mem 0x0000000000090000-0x000000000009dfff]
[    0.013798]   node   0: [mem 0x0000000000100000-0x000000001fffffff]
[    0.013803]   node   0: [mem 0x0000000020200000-0x0000000079bbcfff]
[    0.013808]   node   0: [mem 0x000000007c755000-0x000000007c75efff]
[    0.013813]   node   0: [mem 0x000000007c760000-0x000000007ccfffff]
[    0.013819] Initmem setup node 0 [mem 0x0000000000001000-0x000000007ccfffff]
[    0.013832] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.013838] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.013913] On node 0, zone DMA: 98 pages in unavailable ranges
[    0.024124] On node 0, zone DMA32: 512 pages in unavailable ranges
[    0.024579] On node 0, zone DMA32: 11160 pages in unavailable ranges
[    0.024615] On node 0, zone DMA32: 1 pages in unavailable ranges
[    0.025135] On node 0, zone DMA32: 13056 pages in unavailable ranges
[    0.025145] x86/hpet: Will disable the HPET for this platform because it's not reliable
[    0.025154] Reserving Intel graphics memory at [mem 0x7d000000-0x7effffff]
[    0.025220] TSC deadline timer available
[    0.025229] smpboot: Boot CPU (id 0) not listed by BIOS
[    0.025234] smpboot: Allowing 1 CPUs, 0 hotplug CPUs
[    0.025294] PM: hibernation: Registered nosave memory: [mem 0x00000000-0x00000fff]
[    0.025304] PM: hibernation: Registered nosave memory: [mem 0x0008f000-0x0008ffff]
[    0.025313] PM: hibernation: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[    0.025317] PM: hibernation: Registered nosave memory: [mem 0x000a0000-0x000fffff]
[    0.025325] PM: hibernation: Registered nosave memory: [mem 0x20000000-0x201fffff]
[    0.025333] PM: hibernation: Registered nosave memory: [mem 0x79bbd000-0x7c3c2fff]
[    0.025337] PM: hibernation: Registered nosave memory: [mem 0x7c3c3000-0x7c3f2fff]
[    0.025341] PM: hibernation: Registered nosave memory: [mem 0x7c3f3000-0x7c4a6fff]
[    0.025345] PM: hibernation: Registered nosave memory: [mem 0x7c4a7000-0x7c754fff]
[    0.025353] PM: hibernation: Registered nosave memory: [mem 0x7c75f000-0x7c75ffff]
[    0.025359] [mem 0x7f000000-0xe00f7fff] available for PCI devices
[    0.025366] Booting paravirtualized kernel on bare hardware
[    0.025373] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370452778343963 ns
[    0.038887] setup_percpu: NR_CPUS:320 nr_cpumask_bits:320 nr_cpu_ids:1 nr_node_ids:1
[    0.039613] percpu: Embedded 61 pages/cpu s212992 r8192 d28672 u2097152
[    0.039641] pcpu-alloc: s212992 r8192 d28672 u2097152 alloc=1*2097152
[    0.039652] pcpu-alloc: [0] 0 
[    0.039728] Built 1 zonelists, mobility grouping on.  Total pages: 491315
[    0.039738] Policy zone: DMA32
[    0.039743] Kernel command line: initrd=\arch\boot\intel-ucode.img initrd=\arch\boot\amd-ucode.img initrd=\arch\boot\x86_64\initramfs-linux.img archisobasedir=arch archisolabel=ARCH_202201 acpi=off
[    0.039991] Unknown kernel command line parameters "archisobasedir=arch archisolabel=ARCH_202201", will be passed to user space.
[    0.040608] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.040955] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.041681] mem auto-init: stack:byref_all(zero), heap alloc:on, heap free:off
[    0.058998] Memory: 1815692K/1997836K available (14344K kernel code, 2071K rwdata, 10792K rodata, 1864K init, 3836K bss, 181884K reserved, 0K cma-reserved)
[    0.059018] random: get_random_u64 called from __kmem_cache_create+0x2a/0x540 with crng_init=0
[    0.059611] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.059657] Kernel/User page tables isolation: enabled
[    0.059708] ftrace: allocating 44301 entries in 174 pages
[    0.096420] ftrace: allocated 174 pages with 5 groups
[    0.096722] rcu: Preemptible hierarchical RCU implementation.
[    0.096728] rcu: 	RCU dyntick-idle grace-period acceleration is enabled.
[    0.096730] rcu: 	RCU restricting CPUs from NR_CPUS=320 to nr_cpu_ids=1.
[    0.096735] rcu: 	RCU priority boosting: priority 1 delay 500 ms.
[    0.096739] 	Trampoline variant of Tasks RCU enabled.
[    0.096742] 	Rude variant of Tasks RCU enabled.
[    0.096744] 	Tracing variant of Tasks RCU enabled.
[    0.096747] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.096750] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[    0.113900] NR_IRQS: 20736, nr_irqs: 32, preallocated irqs: 16
[    0.114507] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
[    0.114726] Console: colour dummy device 80x25
[    0.114768] printk: console [tty0] enabled
[    0.114841] APIC: ACPI MADT or MP tables are not detected
[    0.114871] APIC: Switch to virtual wire mode setup with no configuration
[    0.114876] Not enabling interrupt remapping due to skipped IO-APIC setup
[    0.114891] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x13381e82524, max_idle_ns: 440795248224 ns
[    0.114906] Calibrating delay loop (skipped), value calculated using timer frequency.. 2667.77 BogoMIPS (lpj=4444443)
[    0.114917] pid_max: default: 32768 minimum: 301
[    0.118247] spurious 8259A interrupt: IRQ7.
[    0.119679] LSM: Security Framework initializing
[    0.119725] landlock: Up and running.
[    0.119733] Yama: becoming mindful.
[    0.119752] LSM support for eBPF active
[    0.119808] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.119829] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes, linear)
[    0.120640] CPU0: Thermal monitoring enabled (TM1)
[    0.120679] process: using mwait in idle threads
[    0.120687] Last level iTLB entries: 4KB 48, 2MB 0, 4MB 0
[    0.120693] Last level dTLB entries: 4KB 128, 2MB 16, 4MB 16, 1GB 0
[    0.120708] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.120715] Spectre V2 : Mitigation: Full generic retpoline
[    0.120718] Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch
[    0.120721] Spectre V2 : Enabling Restricted Speculation for firmware calls
[    0.120727] Spectre V2 : mitigation: Enabling conditional Indirect Branch Prediction Barrier
[    0.120735] MDS: Mitigation: Clear CPU buffers
[    0.140496] Freeing SMP alternatives memory: 36K
[    0.140756] smpboot: Estimated ratio of average max frequency by base frequency (times 1024): 1408
[    0.140765] smpboot: SMP disabled
[    0.141614] Performance Events: PEBS fmt2+, 8-deep LBR, Silvermont events, 8-deep LBR, full-width counters, Intel PMU driver.
[    0.141643] ... version:                3
[    0.141646] ... bit width:              40
[    0.141649] ... generic registers:      2
[    0.141652] ... value mask:             000000ffffffffff
[    0.141656] ... max period:             0000007fffffffff
[    0.141659] ... fixed-purpose events:   3
[    0.141662] ... event mask:             0000000700000003
[    0.142038] rcu: Hierarchical SRCU implementation.
[    0.143709] NMI watchdog: Enabled. Permanently consumes one hw-PMU counter.
[    0.143827] smp: Bringing up secondary CPUs ...
[    0.143832] smp: Brought up 1 node, 1 CPU
[    0.143838] smpboot: Max logical packages: 1
[    0.143841] smpboot: Total of 1 processors activated (2667.77 BogoMIPS)
[    0.144276] devtmpfs: initialized
[    0.144420] x86/mm: Memory block size: 128MB
[    0.145725] ACPI: PM: Registering ACPI NVS region [mem 0x0008f000-0x0008ffff] (4096 bytes)
[    0.145736] ACPI: PM: Registering ACPI NVS region [mem 0x7c3f3000-0x7c4a6fff] (737280 bytes)
[    0.145917] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.145937] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[    0.146082] pinctrl core: initialized pinctrl subsystem
[    0.146439] PM: RTC time: 14:36:34, date: 2022-01-03
[    0.146854] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.147254] DMA: preallocated 256 KiB GFP_KERNEL pool for atomic allocations
[    0.147337] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.147416] DMA: preallocated 256 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.147462] audit: initializing netlink subsys (disabled)
[    0.148065] thermal_sys: Registered thermal governor 'fair_share'
[    0.148072] thermal_sys: Registered thermal governor 'bang_bang'
[    0.148076] thermal_sys: Registered thermal governor 'step_wise'
[    0.148079] thermal_sys: Registered thermal governor 'user_space'
[    0.148082] thermal_sys: Registered thermal governor 'power_allocator'
[    0.148129] cpuidle: using governor ladder
[    0.148156] cpuidle: using governor menu
[    0.148610] PCI: Using configuration type 1 for base access
[    0.148955] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[    0.151607] audit: type=2000 audit(1641220594.029:1): state=initialized audit_enabled=0 res=1
[    0.154042] Kprobes globally optimized
[    0.154486] HugeTLB: can free 6 vmemmap pages for hugepages-2048kB
[    0.154497] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[    0.160902] ACPI: Interpreter disabled.
[    0.160988] iommu: Default domain type: Translated 
[    0.160994] iommu: DMA domain TLB invalidation policy: lazy mode 
[    0.161093] vgaarb: loaded
[    0.161841] SCSI subsystem initialized
[    0.161988] libata version 3.00 loaded.
[    0.162060] usbcore: registered new interface driver usbfs
[    0.162091] usbcore: registered new interface driver hub
[    0.162116] usbcore: registered new device driver usb
[    0.162221] pps_core: LinuxPPS API ver. 1 registered
[    0.162227] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.162240] PTP clock support registered
[    0.162271] EDAC MC: Ver: 3.0.0
[    0.162529] Registered efivars operations
[    0.163303] NetLabel: Initializing
[    0.163308] NetLabel:  domain hash size = 128
[    0.163312] NetLabel:  protocols = UNLABELED CIPSOv4 CALIPSO
[    0.163375] NetLabel:  unlabeled traffic allowed by default
[    0.163394] PCI: Probing PCI hardware
[    0.163398] PCI: root bus 00: using default resources
[    0.163404] PCI: Probing PCI hardware (bus 00)
[    0.163471] PCI host bridge to bus 0000:00
[    0.163479] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.163489] pci_bus 0000:00: root bus resource [mem 0x00000000-0xfffffffff]
[    0.163496] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.163518] pci 0000:00:00.0: [8086:0f00] type 00 class 0x060000
[    0.163674] pci 0000:00:02.0: [8086:0f31] type 00 class 0x030000
[    0.163694] pci 0000:00:02.0: reg 0x10: [mem 0x90400000-0x907fffff]
[    0.163711] pci 0000:00:02.0: reg 0x18: [mem 0x80000000-0x8fffffff pref]
[    0.163727] pci 0000:00:02.0: reg 0x20: [io  0x1000-0x1007]
[    0.163750] pci 0000:00:02.0: BAR 2: assigned to efifb
[    0.163851] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[    0.163858] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.163895] pci 0000:00:03.0: [8086:0f38] type 00 class 0x048000
[    0.163912] pci 0000:00:03.0: reg 0x10: [mem 0x90000000-0x903fffff]
[    0.164095] pci 0000:00:14.0: [8086:0f35] type 00 class 0x0c0330
[    0.164121] pci 0000:00:14.0: reg 0x10: [mem 0x90e00000-0x90e0ffff 64bit]
[    0.164191] pci 0000:00:14.0: PME# supported from D3hot D3cold
[    0.164315] pci 0000:00:16.0: [8086:0f37] type 00 class 0x0c0380
[    0.164337] pci 0000:00:16.0: reg 0x10: [mem 0x90800000-0x909fffff]
[    0.164352] pci 0000:00:16.0: reg 0x14: [mem 0x90e2c000-0x90e2cfff]
[    0.164416] pci 0000:00:16.0: PME# supported from D0 D3hot
[    0.164543] pci 0000:00:1a.0: [8086:0f18] type 00 class 0x108000
[    0.164575] pci 0000:00:1a.0: reg 0x10: [mem 0x90d00000-0x90dfffff]
[    0.164595] pci 0000:00:1a.0: reg 0x14: [mem 0x90c00000-0x90cfffff]
[    0.164708] pci 0000:00:1a.0: PME# supported from D0 D3hot
[    0.164837] pci 0000:00:1f.0: [8086:0f1c] type 00 class 0x060100
[    0.165074] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    0.165235] PCI: pci_cache_line_size set to 64 bytes
[    0.165264] e820: reserve RAM buffer [mem 0x0008f000-0x0008ffff]
[    0.165272] e820: reserve RAM buffer [mem 0x0009e000-0x0009ffff]
[    0.165278] e820: reserve RAM buffer [mem 0x79bbd000-0x7bffffff]
[    0.165282] e820: reserve RAM buffer [mem 0x7c75f000-0x7fffffff]
[    0.165288] e820: reserve RAM buffer [mem 0x7cd00000-0x7fffffff]
[    0.168818] clocksource: Switched to clocksource tsc-early
[    0.208655] VFS: Disk quotas dquot_6.6.0
[    0.208703] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.208876] pnp: PnP ACPI: disabled
[    0.220053] NET: Registered PF_INET protocol family
[    0.220191] IP idents hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.221471] tcp_listen_portaddr_hash hash table entries: 1024 (order: 2, 16384 bytes, linear)
[    0.221534] TCP established hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.221715] TCP bind hash table entries: 16384 (order: 6, 262144 bytes, linear)
[    0.221835] TCP: Hash tables configured (established 16384 bind 16384)
[    0.228374] MPTCP token hash table entries: 2048 (order: 3, 49152 bytes, linear)
[    0.228454] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.228498] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear)
[    0.228657] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.228678] NET: Registered PF_XDP protocol family
[    0.228700] pci_bus 0000:00: resource 4 [io  0x0000-0xffff]
[    0.228711] pci_bus 0000:00: resource 5 [mem 0x00000000-0xfffffffff]
[    0.228736] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.228761] pci 0000:00:14.0: can't find IRQ for PCI INT A; please try using pci=biosirq
[    0.228820] PCI: CLS 0 bytes, default 64
[    0.228954] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x13381e82524, max_idle_ns: 440795248224 ns
[    0.228996] clocksource: Switched to clocksource tsc
[    0.229067] platform rtc_cmos: registered platform RTC device (no PNP device found)
[    0.229817] Trying to unpack rootfs image as initramfs...
[    0.239543] Initialise system trusted keyrings
[    0.239576] Key type blacklist registered
[    0.241799] workingset: timestamp_bits=41 max_order=19 bucket_order=0
[    0.246408] zbud: loaded
[    0.301674] Key type asymmetric registered
[    0.301685] Asymmetric key parser 'x509' registered
[    0.301753] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[    0.301909] io scheduler mq-deadline registered
[    0.301915] io scheduler kyber registered
[    0.302049] io scheduler bfq registered
[    0.302509] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    0.303240] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[    0.303469] serial8250: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.312435] Non-volatile memory driver v1.3
[    0.312444] Linux agpgart interface v0.103
[    0.312449] AMD-Vi: AMD IOMMUv2 functionality not available on this system - This is not a bug.
[    0.318733] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.318753] ehci-pci: EHCI PCI platform driver
[    0.318786] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.318797] ohci-pci: OHCI PCI platform driver
[    0.318823] uhci_hcd: USB Universal Host Controller Interface driver
[    0.318957] usbcore: registered new interface driver usbserial_generic
[    0.318977] usbserial: USB Serial support registered for generic
[    0.319271] rtc_cmos rtc_cmos: registered as rtc0
[    0.319310] rtc_cmos rtc_cmos: setting system clock to 2022-01-03T14:36:34 UTC (1641220594)
[    0.319363] rtc_cmos rtc_cmos: alarms up to one day, 114 bytes nvram
[    0.319508] intel_pstate: Intel P-state driver initializing
[    0.319776] ledtrig-cpu: registered to indicate activity on CPUs
[    0.320402] efifb: probing for efifb
[    0.320436] efifb: No BGRT, not showing boot graphics
[    0.320440] efifb: framebuffer at 0x80000000, using 1876k, total 1875k
[    0.320446] efifb: mode is 800x600x32, linelength=3200, pages=1
[    0.320451] efifb: scrolling: redraw
[    0.320454] efifb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    0.320607] fbcon: Deferring console take-over
[    0.320613] fb0: EFI VGA frame buffer device
[    0.320666] hid: raw HID events driver (C) Jiri Kosina
[    0.320990] drop_monitor: Initializing network drop monitor service
[    0.321135] Initializing XFRM netlink socket
[    0.321416] NET: Registered PF_INET6 protocol family
[    0.961605] random: fast init done
[   14.588093] Freeing initrd memory: 62704K
[   14.607396] Segment Routing with IPv6
[   14.607405] RPL Segment Routing with IPv6
[   14.607434] In-situ OAM (IOAM) with IPv6
[   14.607494] NET: Registered PF_PACKET protocol family
[   14.607955] microcode: sig=0x30678, pf=0x2, revision=0x838
[   14.607967] microcode: Microcode Update Driver: v2.2.
[   14.607977] IPI shorthand broadcast: enabled
[   14.608014] sched_clock: Marking stable (14604358641, 569916)->(14605482189, -553632)
[   14.608388] registered taskstats version 1
[   14.608502] Loading compiled-in X.509 certificates
[   14.622628] Loaded X.509 cert 'Build time autogenerated kernel key: d2094633047b7eebd2131812d6ef772775a49f35'
[   14.622932] zswap: loaded using pool lz4/z3fold
[   14.623306] Key type ._fscrypt registered
[   14.623311] Key type .fscrypt registered
[   14.623314] Key type fscrypt-provisioning registered
[   14.624322] PM:   Magic number: 6:259:636
[   14.624681] RAS: Correctable Errors collector initialized.
[   14.638894] Freeing unused decrypted memory: 2036K
[   14.639887] Freeing unused kernel image (initmem) memory: 1864K
[   14.639963] Write protecting the kernel read-only data: 28672k
[   14.641358] Freeing unused kernel image (text/rodata gap) memory: 2036K
[   14.642235] Freeing unused kernel image (rodata/data gap) memory: 1496K
[   14.744369] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[   14.744381] rodata_test: all tests were successful
[   14.744400] x86/mm: Checking user space page tables
[   14.843449] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[   14.843501] Run /init as init process
[   14.843505]   with arguments:
[   14.843508]     /init
[   14.843511]   with environment:
[   14.843513]     HOME=/
[   14.843516]     TERM=linux
[   14.843518]     archisobasedir=arch
[   14.843521]     archisolabel=ARCH_202201
[   14.879522] fbcon: Taking over console
[   14.879696] Console: switching to colour frame buffer device 100x37
[   15.501660] cryptd: max_cpu_qlen set to 1000
[   15.546982] xhci_hcd 0000:00:14.0: can't find IRQ for PCI INT A; please try using pci=biosirq
[   15.547030] xhci_hcd 0000:00:14.0: xHCI Host Controller
[   15.547048] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 1
[   15.551265] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x0000000000009810
[   15.551737] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.15
[   15.551746] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   15.551752] usb usb1: Product: xHCI Host Controller
[   15.551756] usb usb1: Manufacturer: Linux 5.15.12-arch1-1 xhci-hcd
[   15.551760] usb usb1: SerialNumber: 0000:00:14.0
[   15.553000] hub 1-0:1.0: USB hub found
[   15.553033] hub 1-0:1.0: 6 ports detected
[   15.556124] xhci_hcd 0000:00:14.0: xHCI Host Controller
[   15.556140] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 2
[   15.556151] xhci_hcd 0000:00:14.0: Host supports USB 3.0 SuperSpeed
[   15.556752] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.15
[   15.556761] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   15.556766] usb usb2: Product: xHCI Host Controller
[   15.556771] usb usb2: Manufacturer: Linux 5.15.12-arch1-1 xhci-hcd
[   15.556775] usb usb2: SerialNumber: 0000:00:14.0
[   15.557550] hub 2-0:1.0: USB hub found
[   15.557579] hub 2-0:1.0: 1 port detected
[   15.618883] SSE version of gcm_enc/dec engaged.
[   15.804960] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[   15.903052] i915 0000:00:02.0: can't find IRQ for PCI INT A; please try using pci=biosirq
[   15.903269] checking generic (80000000 1d5000) vs hw (90400000 400000)
[   15.903276] checking generic (80000000 1d5000) vs hw (80000000 10000000)
[   15.903280] fb0: switching to i915 from EFI VGA
[   15.904205] Console: switching to colour dummy device 80x25
[   15.904696] i915 0000:00:02.0: vgaarb: deactivate vga console
[   15.930556] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
[   15.930931] i915 0000:00:02.0: [drm] HDaudio controller not detected, using LPE audio instead
[   15.946248] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=32.98
[   15.946263] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[   15.946269] usb 1-1: Product: USB2.0 Hub
[   15.947164] hub 1-1:1.0: USB hub found
[   15.947457] hub 1-1:1.0: 4 ports detected
[   16.071628] usb 1-2: new full-speed USB device number 3 using xhci_hcd
[   16.145014] fbcon: i915drmfb (fb0) is primary device
[   16.195265] Console: switching to colour frame buffer device 240x67
[   16.213864] usb 1-2: New USB device found, idVendor=046d, idProduct=c534, bcdDevice=29.00
[   16.213873] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   16.213878] usb 1-2: Product: USB Receiver
[   16.213881] usb 1-2: Manufacturer: Logitech
[   16.242819] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
[   16.284995] usb 1-1.1: new high-speed USB device number 4 using xhci_hcd
[   16.304238] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/0003:046D:C534.0001/input/input0
[   16.361044] hid-generic 0003:046D:C534.0001: input,hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:14.0-2/input0
[   16.365243] input: Logitech USB Receiver Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1/0003:046D:C534.0002/input/input1
[   16.365549] input: Logitech USB Receiver Consumer Control as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1/0003:046D:C534.0002/input/input2
[   16.376066] usb 1-1.1: New USB device found, idVendor=0bda, idProduct=8152, bcdDevice=20.00
[   16.376079] usb 1-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   16.376086] usb 1-1.1: Product: USB 10/100 LAN
[   16.376091] usb 1-1.1: Manufacturer: Realtek
[   16.376096] usb 1-1.1: SerialNumber: 1000003200C8
[   16.421882] input: Logitech USB Receiver System Control as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1/0003:046D:C534.0002/input/input3
[   16.422822] hid-generic 0003:046D:C534.0002: input,hiddev96,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:14.0-2/input1
[   16.422957] usbcore: registered new interface driver usbhid
[   16.422963] usbhid: USB HID core driver
[   16.444404] usbcore: registered new interface driver r8152
[   16.448317] usb 1-1.2: new high-speed USB device number 5 using xhci_hcd
[   16.514417] usbcore: registered new interface driver cdc_ether
[   16.528525] logitech-djreceiver 0003:046D:C534.0001: hidraw0: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:14.0-2/input0
[   16.547898] usb 1-1.2: New USB device found, idVendor=0951, idProduct=1666, bcdDevice= 0.01
[   16.547909] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[   16.547915] usb 1-1.2: Product: DataTraveler 3.0
[   16.547920] usb 1-1.2: Manufacturer: Kingston
[   16.547924] usb 1-1.2: SerialNumber: E839354C74CEF360673D0CAF
[   16.583110] usb-storage 1-1.2:1.0: USB Mass Storage device detected
[   16.584258] scsi host0: usb-storage 1-1.2:1.0
[   16.586451] usbcore: registered new interface driver usb-storage
[   16.605851] usbcore: registered new interface driver uas
[   16.611900] usb 1-1.1: reset high-speed USB device number 4 using xhci_hcd
[   16.627494] logitech-djreceiver 0003:046D:C534.0002: hiddev96,hidraw1: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:14.0-2/input1
[   16.684148] logitech-djreceiver 0003:046D:C534.0002: device of type eQUAD nano Lite (0x0a) connected on slot 1
[   16.685155] input: Logitech Wireless Keyboard PID:4023 Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1/0003:046D:C534.0002/0003:046D:4023.0003/input/input6
[   16.685729] hid-generic 0003:046D:4023.0003: input,hidraw2: USB HID v1.11 Keyboard [Logitech Wireless Keyboard PID:4023] on usb-0000:00:14.0-2/input1:1
[   16.686110] logitech-djreceiver 0003:046D:C534.0002: device of type eQUAD nano Lite (0x0a) connected on slot 2
[   16.686803] input: Logitech Wireless Mouse PID:4038 Mouse as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1/0003:046D:C534.0002/0003:046D:4038.0004/input/input11
[   16.686979] hid-generic 0003:046D:4038.0004: input,hidraw3: USB HID v1.11 Mouse [Logitech Wireless Mouse PID:4038] on usb-0000:00:14.0-2/input1:2
[   16.729281] r8152 1-1.1:1.0: skip request firmware
[   16.755758] r8152 1-1.1:1.0 eth0: v1.12.12
[   16.786648] input: Logitech Wireless Keyboard PID:4023 as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1/0003:046D:C534.0002/0003:046D:4023.0003/input/input15
[   16.789266] logitech-hidpp-device 0003:046D:4023.0003: input,hidraw2: USB HID v1.11 Keyboard [Logitech Wireless Keyboard PID:4023] on usb-0000:00:14.0-2/input1:1
[   16.802732] input: Logitech Wireless Mouse PID:4038 as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1/0003:046D:C534.0002/0003:046D:4038.0004/input/input16
[   16.802934] logitech-hidpp-device 0003:046D:4038.0004: input,hidraw3: USB HID v1.11 Mouse [Logitech Wireless Mouse PID:4038] on usb-0000:00:14.0-2/input1:2
[   17.609295] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 3.0      PQ: 0 ANSI: 6
[   17.611648] sd 0:0:0:0: [sda] 30218842 512-byte logical blocks: (15.5 GB/14.4 GiB)
[   17.611895] sd 0:0:0:0: [sda] Write Protect is off
[   17.611905] sd 0:0:0:0: [sda] Mode Sense: 4f 00 00 00
[   17.612138] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[   17.615071]  sda: sda1 sda2
[   17.616357] sd 0:0:0:0: [sda] Attached SCSI removable disk
[   18.468084] ISO 9660 Extensions: Microsoft Joliet Level 3
[   18.469217] ISO 9660 Extensions: RRIP_1991A
[   18.505881] loop: module loaded
[   18.507827] loop0: detected capacity change from 0 to 1465200
[   18.630227] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   18.681358] overlayfs: "xino" feature enabled using 2 upper inode bits.
[   19.067676] random: crng init done
[   22.617325] systemd[1]: systemd 250-4-arch running in system mode (+PAM +AUDIT -SELINUX -APPARMOR -IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT -QRENCODE +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK +XKBCOMMON +UTMP -SYSVINIT default-hierarchy=unified)
[   22.631906] systemd[1]: Detected architecture x86-64.
[   22.741559] systemd[1]: Hostname set to <archiso>.
[   22.744752] systemd[1]: Initializing machine ID from random generator.
[   23.882758] systemd-gpt-auto-generator[202]: EFI loader partition unknown, exiting.
[   23.882776] systemd-gpt-auto-generator[202]: (The boot loader did not set EFI variable LoaderDevicePartUUID.)
[   27.722809] systemd[191]: /usr/lib/systemd/system-generators/systemd-gpt-auto-generator failed with exit status 1.
[   28.097062] systemd[1]: Queued start job for default target Graphical Interface.
[   28.100892] systemd[1]: Created slice Slice /system/getty.
[   28.102952] systemd[1]: Created slice Slice /system/modprobe.
[   28.104438] systemd[1]: Created slice User and Session Slice.
[   28.105137] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[   28.105719] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[   28.106663] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[   28.107112] systemd[1]: Reached target Local Encrypted Volumes.
[   28.107509] systemd[1]: Reached target Local Integrity Protected Volumes.
[   28.107935] systemd[1]: Reached target Path Units.
[   28.108356] systemd[1]: Reached target Remote File Systems.
[   28.108705] systemd[1]: Reached target Slice Units.
[   28.109064] systemd[1]: Reached target Swaps.
[   28.109430] systemd[1]: Reached target Local Verity Protected Volumes.
[   28.110067] systemd[1]: Listening on Device-mapper event daemon FIFOs.
[   28.113378] systemd[1]: Listening on LVM2 poll daemon socket.
[   28.120035] systemd[1]: Listening on Process Core Dump Socket.
[   28.121796] systemd[1]: Listening on Journal Audit Socket.
[   28.122698] systemd[1]: Listening on Journal Socket (/dev/log).
[   28.123584] systemd[1]: Listening on Journal Socket.
[   28.124621] systemd[1]: Listening on Network Service Netlink Socket.
[   28.129326] systemd[1]: Listening on udev Control Socket.
[   28.130147] systemd[1]: Listening on udev Kernel Socket.
[   28.133852] systemd[1]: Mounting Huge Pages File System...
[   28.138188] systemd[1]: Mounting POSIX Message Queue File System...
[   28.149719] systemd[1]: Mounting Kernel Debug File System...
[   28.155307] systemd[1]: Mounting Kernel Trace File System...
[   28.237265] systemd[1]: Mounting Temporary Directory /tmp...
[   28.245813] systemd[1]: Starting Create List of Static Device Nodes...
[   28.255431] systemd[1]: Starting Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling...
[   28.292905] systemd[1]: Starting Load Kernel Module configfs...
[   28.309923] systemd[1]: Starting Load Kernel Module drm...
[   28.338772] systemd[1]: Starting Load Kernel Module fuse...
[   28.352857] systemd[1]: OpenVSwitch configuration for cleanup was skipped because of a failed condition check (ConditionFileIsExecutable=/usr/bin/ovs-vsctl).
[   28.368936] systemd[1]: Starting Journal Service...
[   28.525905] systemd[1]: Starting Load Kernel Modules...
[   28.540859] systemd[1]: Starting Remount Root and Kernel File Systems...
[   28.601914] fuse: init (API version 7.34)
[   28.605762] systemd[1]: Repartition Root Disk was skipped because all trigger condition checks failed.
[   28.609192] systemd[1]: Starting Coldplug All udev Devices...
[   28.621195] systemd[1]: Mounted Huge Pages File System.
[   28.622056] systemd[1]: Mounted POSIX Message Queue File System.
[   28.622767] systemd[1]: Mounted Kernel Debug File System.
[   28.623453] systemd[1]: Mounted Kernel Trace File System.
[   28.624134] systemd[1]: Mounted Temporary Directory /tmp.
[   28.688535] systemd[1]: Finished Create List of Static Device Nodes.
[   28.690192] systemd[1]: Finished Monitoring of LVM2 mirrors, snapshots etc. using dmeventd or progress polling.
[   28.696136] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[   28.696727] systemd[1]: Finished Load Kernel Module configfs.
[   28.702411] systemd[1]: modprobe@drm.service: Deactivated successfully.
[   28.702983] systemd[1]: Finished Load Kernel Module drm.
[   28.709132] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[   28.709705] systemd[1]: Finished Load Kernel Module fuse.
[   28.721931] systemd[1]: Mounting FUSE Control File System...
[   28.745616] systemd[1]: Mounting Kernel Configuration File System...
[   28.863149] systemd[1]: Finished Remount Root and Kernel File Systems.
[   28.870496] systemd[1]: Mounted FUSE Control File System.
[   28.876838] systemd[1]: Mounted Kernel Configuration File System.
[   28.935278] systemd[1]: First Boot Wizard was skipped because of a failed condition check (ConditionFirstBoot=yes).
[   28.942593] systemd[1]: Rebuild Hardware Database was skipped because all trigger condition checks failed.
[   28.949106] systemd[1]: Starting Load/Save Random Seed...
[   29.022125] systemd[1]: Starting Create System Users...
[   29.333646] Asymmetric key parser 'pkcs8' registered
[   29.336195] systemd[1]: Finished Load Kernel Modules.
[   29.345466] audit: type=1130 audit(1641220623.523:2): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-modules-load comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   29.359708] systemd[1]: Starting Apply Kernel Variables...
[   29.612882] systemd[1]: Finished Load/Save Random Seed.
[   29.619683] audit: type=1130 audit(1641220623.796:3): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-random-seed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   29.622082] systemd[1]: First Boot Complete was skipped because of a failed condition check (ConditionFirstBoot=yes).
[   29.861295] systemd[1]: Started Journal Service.
[   29.864569] audit: type=1130 audit(1641220624.040:4): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journald comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   29.970960] audit: type=1130 audit(1641220624.146:5): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-sysusers comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   30.113021] systemd-journald[230]: Received client request to flush runtime journal.
[   30.126885] audit: type=1130 audit(1641220624.303:6): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-journal-flush comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   30.137174] audit: type=1130 audit(1641220624.313:7): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-sysctl comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   30.144837] audit: type=1130 audit(1641220624.320:8): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udev-trigger comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   30.414405] audit: type=1130 audit(1641220624.590:9): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-tmpfiles-setup-dev comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   30.439996] audit: type=1334 audit(1641220624.616:10): prog-id=14 op=LOAD
[   30.442262] audit: type=1334 audit(1641220624.620:11): prog-id=15 op=LOAD
[   39.332962] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   39.466144] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   39.918539] kauditd_printk_skb: 8 callbacks suppressed
[   39.918546] audit: type=1130 audit(1641220634.096:20): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-networkd comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   39.991244] audit: type=1334 audit(1641220634.166:21): prog-id=18 op=LOAD
[   46.910482] audit: type=1130 audit(1641220641.086:22): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-resolved comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   48.637962] input: PC Speaker as /devices/platform/pcspkr/input/input17
[   57.173889] intel_soc_dts_thermal: request_threaded_irq ret -22
[   57.755846] intel_rapl_common: Found RAPL domain package
[   57.755855] intel_rapl_common: Found RAPL domain core
[   58.905755] mei_txe 0000:00:1a.0: can't find IRQ for PCI INT A; please try using pci=biosirq
[   58.912146] mc: Linux media interface: v0.10
[   59.115640] iTCO_vendor_support: vendor-support=0
[   59.314491] videodev: Linux video capture interface: v2.00
[   59.428840] iTCO_wdt iTCO_wdt.0.auto: Found a Bay Trail SoC TCO device (Version=3, TCOBASE=0x0460)
[   59.433381] iTCO_wdt iTCO_wdt.0.auto: initialized. heartbeat=30 sec (nowayout=0)
[   59.613924] intel-spi intel-spi: w25q64dw (8192 Kbytes)
[   59.768370] Creating 1 MTD partitions on "intel-spi":
[   59.768387] 0x000000000000-0x000000800000 : "BIOS"
[   59.868482] atomisp_gmin_platform: module is from the staging directory, the quality is unknown, you have been warned.
[   59.916752] input: Intel HDMI/DP LPE Audio HDMI/DP,pcm=0 as /devices/pci0000:00/0000:00:02.0/hdmi-lpe-audio/sound/card0/input18
[   59.917434] input: Intel HDMI/DP LPE Audio HDMI/DP,pcm=1 as /devices/pci0000:00/0000:00:02.0/hdmi-lpe-audio/sound/card0/input19
[   60.334654] atomisp: module is from the staging directory, the quality is unknown, you have been warned.

[   60.405203] **********************************************************
[   60.405205] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[   60.405208] **                                                      **
[   60.405209] ** trace_printk() being used. Allocating extra memory.  **
[   60.405211] **                                                      **
[   60.405213] ** This means that this is a DEBUG kernel and it is     **
[   60.405215] ** unsafe for production use.                           **
[   60.405217] **                                                      **
[   60.405219] ** If you see this message and you are not debugging    **
[   60.405221] ** the kernel, report this immediately to your vendor!  **
[   60.405223] **                                                      **
[   60.405224] **   NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE   **
[   60.405226] **********************************************************
[   60.408111] atomisp-isp2 0000:00:03.0: Support for Baytrail (ISP2400) was disabled at compile time
[   63.270961] dwc3-pci 0000:00:16.0: can't find IRQ for PCI INT A; please try using pci=biosirq
[   63.275032] dwc3-pci 0000:00:16.0: cannot find GPIO chip INT33FC:02, deferring
[   66.589339] mousedev: PS/2 mouse device common for all mice
[   68.396810] r8152 1-1.1:1.0 enp0s20u1u1: renamed from eth0
[   68.523060] audit: type=1130 audit(1641220662.700:23): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-udev-settle comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   68.661388] IPv6: ADDRCONF(NETDEV_CHANGE): enp0s20u1u1: link becomes ready
[   68.665147] r8152 1-1.1:1.0 enp0s20u1u1: carrier on
[   70.976156] audit: type=1130 audit(1641220665.153:24): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-networkd-wait-online comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   74.696819] audit: type=1130 audit(1641220668.873:25): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=ldconfig comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   74.797599] audit: type=1130 audit(1641220668.973:26): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-update-done comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   74.896043] audit: type=1130 audit(1641220669.073:27): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=dbus comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   74.900092] audit: type=1334 audit(1641220669.076:28): prog-id=19 op=LOAD
[   75.159957] audit: type=1334 audit(1641220669.336:29): prog-id=20 op=LOAD
[   75.160696] audit: type=1334 audit(1641220669.336:30): prog-id=21 op=LOAD
[   75.161009] audit: type=1334 audit(1641220669.336:31): prog-id=22 op=LOAD
[   75.203586] audit: type=1130 audit(1641220669.380:32): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=alsa-restore comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   77.110377] NET: Registered PF_ALG protocol family
[   77.747475] audit: type=1130 audit(1641220671.923:33): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-logind comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   79.024033] audit: type=1130 audit(1641220673.200:34): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=iwd comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   86.289088] kauditd_printk_skb: 3 callbacks suppressed
[   86.289095] audit: type=1101 audit(1641220680.466:38): pid=391 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:accounting grantors=pam_access,pam_unix,pam_permit,pam_time acct="root" exe="/usr/bin/login" hostname=archiso addr=? terminal=/dev/tty1 res=success'
[   86.293082] audit: type=1103 audit(1641220680.470:39): pid=391 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:setcred grantors=pam_securetty,pam_shells,pam_faillock,pam_permit,pam_env,pam_faillock acct="root" exe="/usr/bin/login" hostname=archiso addr=? terminal=/dev/tty1 res=success'
[   86.293647] audit: type=1006 audit(1641220680.470:40): pid=391 uid=0 old-auid=4294967295 auid=0 tty=tty1 old-ses=4294967295 ses=1 res=1
[   86.293754] audit: type=1300 audit(1641220680.470:40): arch=c000003e syscall=1 success=yes exit=1 a0=4 a1=7ffdfd13ba10 a2=1 a3=0 items=0 ppid=1 pid=391 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=tty1 ses=1 comm="login" exe="/usr/bin/login" key=(null)
[   86.294260] audit: type=1327 audit(1641220680.470:40): proctitle=2F62696E2F6C6F67696E002D66
[   87.004625] audit: type=1130 audit(1641220681.180:41): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=user-runtime-dir@0 comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   87.189508] audit: type=1101 audit(1641220681.366:42): pid=421 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:accounting grantors=pam_access,pam_unix,pam_permit,pam_time acct="root" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   87.193026] audit: type=1103 audit(1641220681.370:43): pid=421 uid=0 auid=4294967295 ses=4294967295 msg='op=PAM:setcred grantors=? acct="root" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=failed'
[   87.193541] audit: type=1006 audit(1641220681.370:44): pid=421 uid=0 old-auid=4294967295 auid=0 tty=(none) old-ses=4294967295 ses=2 res=1
[   87.193647] audit: type=1300 audit(1641220681.370:44): arch=c000003e syscall=1 success=yes exit=1 a0=9 a1=7fff1fb2d4f0 a2=1 a3=0 items=0 ppid=1 pid=421 auid=0 uid=0 gid=0 euid=0 suid=0 fsuid=0 egid=0 sgid=0 fsgid=0 tty=(none) ses=2 comm="(systemd)" exe="/usr/lib/systemd/systemd" key=(null)
[   93.211290] kauditd_printk_skb: 13 callbacks suppressed
[   93.211297] audit: type=1130 audit(1641220687.386:53): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=sshdgenkeys comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[   93.231908] audit: type=1130 audit(1641220687.410:54): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=sshd comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  101.236728] audit: type=1334 audit(1641220695.413:55): prog-id=26 op=LOAD
[  101.238958] audit: type=1334 audit(1641220695.416:56): prog-id=27 op=LOAD
[  101.241921] audit: type=1334 audit(1641220695.420:57): prog-id=28 op=LOAD
[  101.952702] audit: type=1130 audit(1641220696.130:58): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  112.659113] audit: type=1130 audit(1641220706.833:59): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=polkit comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  114.328677] NET: Registered PF_QIPCRTR protocol family
[  114.339636] audit: type=1130 audit(1641220708.516:60): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=ModemManager comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  117.344192] logitech-hidpp-device 0003:046D:4038.0004: HID++ 2.0 device connected.
[  126.826199] logitech-hidpp-device 0003:046D:4023.0003: HID++ 2.0 device connected.
[  132.000109] audit: type=1131 audit(1641220726.176:61): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=systemd-hostnamed comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  132.028482] audit: type=1334 audit(1641220726.206:62): prog-id=0 op=UNLOAD
[  132.028499] audit: type=1334 audit(1641220726.206:63): prog-id=0 op=UNLOAD
[  132.028509] audit: type=1334 audit(1641220726.206:64): prog-id=0 op=UNLOAD
[  159.123090] audit: type=1130 audit(1641220753.300:65): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=reflector comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  159.123390] audit: type=1131 audit(1641220753.300:66): pid=1 uid=0 auid=4294967295 ses=4294967295 msg='unit=reflector comm="systemd" exe="/usr/lib/systemd/systemd" hostname=? addr=? terminal=? res=success'
[  159.128624] audit: type=1334 audit(1641220753.306:67): prog-id=0 op=UNLOAD

trapanator

Member

From: Italy

Registered: 2009-08-10

Posts: 151

Re: Booting the ArchLinux installer from usb doesn't detect internal eMMC

note: Fedora 35 and Ubuntu 20.04 installers can see the device

Lone_Wolf

Member

From: Netherlands, Europe

Registered: 2005-10-04

Posts: 11,911

Re: Booting the ArchLinux installer from usb doesn't detect internal eMMC

[   60.408111] atomisp-isp2 0000:00:03.0: Support for Baytrail (ISP2400) was disabled at compile time

There are intel Atom System-on-Chip that require 32-bit efi firmware although they're 64-bit processors .
The bootloader used on archlinux installation iso doesn't support that .

Check https://wiki.archlinux.org/title/Unifie … re_bitness

---

Disliking systemd intensely, but not satisfied with alternatives so focusing on taming systemd.

(A works at time B)  && (time C > time B ) ≠  (A works at time C)

Head_on_a_Stick

Member

From: London

Registered: 2014-02-20

Posts: 7,732

Website

Re: Booting the ArchLinux installer from usb doesn't detect internal eMMC

@Lone_Wolf: the bug report now states the probable cause:

Probably missing this backport from efivar. It was pointed out in #archlinux-releng a day or two ago.

https://github.com/rhboot/efivar/commit … 82d1ccdd33

---

Are you infected with Wetiko?

trapanator

Member

From: Italy

Registered: 2009-08-10

Posts: 151

Re: Booting the ArchLinux installer from usb doesn't detect internal eMMC

[   60.408111] atomisp-isp2 0000:00:03.0: Support for Baytrail (ISP2400) was disabled at compile time

There are intel Atom System-on-Chip that require 32-bit efi firmware although they're 64-bit processors .
The bootloader used on archlinux installation iso doesn't support that .

Check https://wiki.archlinux.org/title/Unifie … re_bitness

Yes, but my Baytrail system was the Android version and not Windows.
It has NO problems installing Ubuntu or Fedora 64 bit with the standard 64 bit medium

progandy

Member

Registered: 2012-05-17

Posts: 5,190

Re: Booting the ArchLinux installer from usb doesn't detect internal eMMC

Do you boot Ubuntu or Fedora with acpi=off as well? If not, does that change the visibility of the eMMC?

Last edited by progandy (2022-01-03 17:26:03)

---

| alias CUTF='LANG=en_XX.UTF-8@POSIX ' |

trapanator

Member

From: Italy

Registered: 2009-08-10

Posts: 151

Re: Booting the ArchLinux installer from usb doesn't detect internal eMMC

UPDATE from bug report: instead of using acpi=off, I can use `nolapic` in boot parameter.

Do you boot Ubuntu or Fedora with acpi=off as well? If not, does that change the visibility of the eMMC?

- Ubuntu 20.04 installer: all OK without acpi=off
- Fedora 35: installer OK without acpi=off,  BUT after reboot to installed system, the screen is black. So I think I should put the nolapci here, too.