You are not logged in.

#1 2021-12-23 15:07:34

Onmp314
Member
Registered: 2021-12-23
Posts: 7

Internet from Wi-Fi not working after upgrading packages

Hello!

I have such a very annoying problem. It came out as I updated the packages today. I am not sure if it is the fault of the new kernel or some other package.

Just in case, I put the logs below:

[2021-12-23T15:52:29+0100] [PACMAN] Running 'pacman -S -y -u --config /etc/pacman.conf --'
[2021-12-23T15:52:29+0100] [PACMAN] synchronizing package lists
[2021-12-23T15:52:30+0100] [PACMAN] starting full system upgrade
[2021-12-23T15:53:12+0100] [ALPM] running '60-mkinitcpio-remove.hook'...
[2021-12-23T15:53:12+0100] [ALPM] transaction started
[2021-12-23T15:53:12+0100] [ALPM] upgraded protobuf (3.17.3-3 -> 3.19.1-1)
[2021-12-23T15:53:12+0100] [ALPM] upgraded kosmindoormap (21.12.0-1 -> 21.12.0-2)
[2021-12-23T15:53:13+0100] [ALPM] upgraded libphonenumber (8.12.39-2 -> 8.12.39-3)
[2021-12-23T15:53:15+0100] [ALPM] upgraded linux (5.15.10.arch1-1 -> 5.15.11.arch2-1)
[2021-12-23T15:53:15+0100] [ALPM] upgraded marble-common (21.12.0-1 -> 21.12.0-3)
[2021-12-23T15:53:15+0100] [ALPM] upgraded marble (21.12.0-1 -> 21.12.0-3)
[2021-12-23T15:53:15+0100] [ALPM] upgraded virtualbox-host-modules-arch (6.1.30-7 -> 6.1.30-8)
[2021-12-23T15:53:16+0100] [ALPM] upgraded vlc (3.0.16-4 -> 3.0.16-5)
[2021-12-23T15:53:16+0100] [ALPM] transaction completed
[2021-12-23T15:53:16+0100] [ALPM] running '30-systemd-update.hook'...
[2021-12-23T15:53:16+0100] [ALPM] running '30-update-mime-database.hook'...
[2021-12-23T15:53:17+0100] [ALPM] running '60-depmod.hook'...
[2021-12-23T15:53:19+0100] [ALPM] running '90-mkinitcpio-install.hook'...
[2021-12-23T15:53:19+0100] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
[2021-12-23T15:53:19+0100] [ALPM-SCRIPTLET]   -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
[2021-12-23T15:53:19+0100] [ALPM-SCRIPTLET] ==> Starting build: 5.15.11-arch2-1
[2021-12-23T15:53:19+0100] [ALPM-SCRIPTLET]   -> Running build hook: [base]
[2021-12-23T15:53:19+0100] [ALPM-SCRIPTLET]   -> Running build hook: [udev]
[2021-12-23T15:53:19+0100] [ALPM-SCRIPTLET]   -> Running build hook: [autodetect]
[2021-12-23T15:53:19+0100] [ALPM-SCRIPTLET]   -> Running build hook: [modconf]
[2021-12-23T15:53:20+0100] [ALPM-SCRIPTLET]   -> Running build hook: [block]
[2021-12-23T15:53:20+0100] [ALPM-SCRIPTLET]   -> Running build hook: [filesystems]
[2021-12-23T15:53:20+0100] [ALPM-SCRIPTLET]   -> Running build hook: [keyboard]
[2021-12-23T15:53:20+0100] [ALPM-SCRIPTLET]   -> Running build hook: [fsck]
[2021-12-23T15:53:20+0100] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2021-12-23T15:53:20+0100] [ALPM-SCRIPTLET] ==> Creating zstd-compressed initcpio image: /boot/initramfs-linux.img
[2021-12-23T15:53:21+0100] [ALPM-SCRIPTLET] ==> Image generation successful
[2021-12-23T15:53:21+0100] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'fallback'
[2021-12-23T15:53:21+0100] [ALPM-SCRIPTLET]   -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
[2021-12-23T15:53:21+0100] [ALPM-SCRIPTLET] ==> Starting build: 5.15.11-arch2-1
[2021-12-23T15:53:21+0100] [ALPM-SCRIPTLET]   -> Running build hook: [base]
[2021-12-23T15:53:21+0100] [ALPM-SCRIPTLET]   -> Running build hook: [udev]
[2021-12-23T15:53:21+0100] [ALPM-SCRIPTLET]   -> Running build hook: [modconf]
[2021-12-23T15:53:21+0100] [ALPM-SCRIPTLET]   -> Running build hook: [block]
[2021-12-23T15:53:23+0100] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: aic94xx
[2021-12-23T15:53:23+0100] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: wd719x
[2021-12-23T15:53:24+0100] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: xhci_pci
[2021-12-23T15:53:25+0100] [ALPM-SCRIPTLET]   -> Running build hook: [filesystems]
[2021-12-23T15:53:26+0100] [ALPM-SCRIPTLET]   -> Running build hook: [keyboard]
[2021-12-23T15:53:27+0100] [ALPM-SCRIPTLET]   -> Running build hook: [fsck]
[2021-12-23T15:53:27+0100] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2021-12-23T15:53:27+0100] [ALPM-SCRIPTLET] ==> Creating zstd-compressed initcpio image: /boot/initramfs-linux-fallback.img
[2021-12-23T15:53:28+0100] [ALPM-SCRIPTLET] ==> Image generation successful
[2021-12-23T15:53:29+0100] [ALPM] running 'gtk-update-icon-cache.hook'...
[2021-12-23T15:53:29+0100] [ALPM] running 'update-desktop-database.hook'...
[2021-12-23T15:53:29+0100] [ALPM] running 'update-vlc-plugin-cache.hook'...

Has anyone had a similar problem? If so, I would love for someone to provide a solution to this problem. I would be grateful for even the smallest help. wink

Last edited by Onmp314 (2022-01-11 17:03:14)

Offline

#2 2021-12-23 17:07:23

seth
Member
Registered: 2012-09-03
Posts: 28,811

Re: Internet from Wi-Fi not working after upgrading packages

ethtool is at 5.15 since mid november, isn't in your list of updates and also not really relevant to wifi.

Please post a complete system journal.
You can use the tip from the 1st link below or "code" tags, not "quote" tags. Please also edit your initial post itr.

Offline

#3 2021-12-23 19:09:51

Onmp314
Member
Registered: 2021-12-23
Posts: 7

Re: Internet from Wi-Fi not working after upgrading packages

Unfortunately, a large number of journal lines cannot be uploaded here, so I post on Google Drive:
https://drive.google.com/file/d/1qkR70w … sp=sharing

Offline

#4 2021-12-23 19:58:19

seth
Member
Registered: 2012-09-03
Posts: 28,811

Re: Internet from Wi-Fi not working after upgrading packages

Before I download the last year of your session journals:

sudo journalctl -b | curl -F 'f:1=<-' ix.io

Offline

#5 2021-12-27 10:56:30

Onmp314
Member
Registered: 2021-12-23
Posts: 7

Re: Internet from Wi-Fi not working after upgrading packages

Ethtool 5.15 seems to work fine with systemd 250 already.

EDIT: [deleted note]

Last edited by Onmp314 (2021-12-27 18:54:14)

Offline

#6 2022-01-09 07:00:44

Onmp314
Member
Registered: 2021-12-23
Posts: 7

Re: Internet from Wi-Fi not working after upgrading packages

Unfortunately, this problem has returned. Logs:
http://ix.io/3LAU

Offline

#7 2022-01-09 08:21:46

seth
Member
Registered: 2012-09-03
Posts: 28,811

Re: Internet from Wi-Fi not working after upgrading packages

The journal is only less than 2 minutes - is it supposed to cover the wifi issues?

Jan 09 07:58:58 ThinkPad-T420 wpa_supplicant[458]: wlan0: CTRL-EVENT-SIGNAL-CHANGE above=1 signal=-14 noise=9999 txrate=1000
…
Jan 09 07:58:58 ThinkPad-T420 NetworkManager[413]: <info>  [1641711538.4729] manager: NetworkManager state is now CONNECTED_GLOBAL
…
Jan 09 07:59:05 ThinkPad-T420 wpa_supplicant[458]: wlan0: CTRL-EVENT-SIGNAL-CHANGE above=1 signal=-8 noise=9999 txrate=24000

You've a wifi connection and NM thinks you've internet access and the signal is excellent.

Jan 09 07:59:14 ThinkPad-T420 NetworkManager[413]: <info>  [1641711554.7350] device (enp0s25): carrier: link connected

You plug the ethernet cable - you later get a new lease on that but NM doesn't seem to disconnect the wifi

Why did you plug the ethernet (there's no indication of wifi or network troubles before) and what do

rfkill; ip a; ip r

look afterwards?

Offline

#8 2022-01-09 08:48:08

Onmp314
Member
Registered: 2021-12-23
Posts: 7

Re: Internet from Wi-Fi not working after upgrading packages

The problem is that when I connect to Wi-Fi it is not able to load any page. The limited connection warning appears after a few minutes. I connected the Ethernet to access the Internet.

Command

rfkill; ip a; ip r

returns:

ID TYPE      DEVICE                   SOFT      HARD
 0 bluetooth tpacpi_bluetooth_sw unblocked unblocked
 1 wwan      tpacpi_wwan_sw      unblocked unblocked
 2 wlan      phy0                unblocked unblocked
 3 bluetooth hci0                unblocked unblocked
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: enp0s25: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether 00:21:cc:cd:09:bf brd ff:ff:ff:ff:ff:ff
    inet 192.168.0.110/24 brd 192.168.0.255 scope global dynamic noprefixroute enp0s25
       valid_lft 3953sec preferred_lft 3953sec
    inet6 fe80::2100:418e:e3a6:1ec9/64 scope link noprefixroute 
       valid_lft forever preferred_lft forever
3: wlan0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 60:67:20:e3:b0:f8 brd ff:ff:ff:ff:ff:ff
    inet 192.168.0.106/24 brd 192.168.0.255 scope global dynamic noprefixroute wlan0
       valid_lft 3919sec preferred_lft 3919sec
    inet6 fe80::5275:4b28:8026:41a1/64 scope link noprefixroute 
       valid_lft forever preferred_lft forever
4: wwp0s29u1u4i6: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000
    link/ether 02:80:37:ec:02:00 brd ff:ff:ff:ff:ff:ff
default via 192.168.0.1 dev enp0s25 proto dhcp metric 100 
default via 192.168.0.1 dev wlan0 proto dhcp metric 20600 
192.168.0.0/24 dev enp0s25 proto kernel scope link src 192.168.0.110 metric 100 
192.168.0.0/24 dev wlan0 proto kernel scope link src 192.168.0.106 metric 600

Offline

#9 2022-01-09 08:57:13

seth
Member
Registered: 2012-09-03
Posts: 28,811

Re: Internet from Wi-Fi not working after upgrading packages

You connected the ethernet adapter after 16 seconds…
Please reboot w/o the ethernet, wait until the wifi fails and before connecting the ethernet, check

ip a; ip r
ping -c1 google.com
ping -c1 8.8.8.8
dig google.com
dig @8.8.8.8 google.com

then plug the wired connection and post the outputs of the above as well as an updated journal.

Some APs don't like https://wiki.archlinux.org/title/Networ … domization so try to disable that.

Offline

#10 2022-01-09 09:11:57

Onmp314
Member
Registered: 2021-12-23
Posts: 7

Re: Internet from Wi-Fi not working after upgrading packages

New logs:
http://ix.io/3LBF

Last edited by Onmp314 (2022-01-11 17:04:36)

Offline

#11 2022-01-09 09:22:17

seth
Member
Registered: 2012-09-03
Posts: 28,811

Re: Internet from Wi-Fi not working after upgrading packages

Mark resolved threads by editing your initial posts subject - so others will know that there's no task left, but maybe a solution to find.
Thanks.

(Others can't do that for you)

Offline

#12 2022-01-11 17:04:47

Onmp314
Member
Registered: 2021-12-23
Posts: 7

Re: Internet from Wi-Fi not working after upgrading packages

The problem is back. I am just asking for a permanent, not temporary solution. http://ix.io/3LTQ

EDIT: Internet again works. I do not mark the topic as [SOLVED] because the problem may come back at any time.

Last edited by Onmp314 (2022-01-11 19:04:22)

Offline

#13 2022-01-11 20:13:02

seth
Member
Registered: 2012-09-03
Posts: 28,811

Re: Internet from Wi-Fi not working after upgrading packages

Please don't edit your older posts in a context altering way - it makes the thread less comprehendable for future readers.
# 10 originally suggested that you had solved the problem by disabling the MAC randomization. This may or not have been a misconception, but is valuable information in either case.

http://ix.io/3LBF had

Jan 09 10:01:21 ThinkPad-T420 NetworkManager[413]: <info>  [1641718881.3088] device (wlan0): set-hw-addr: set MAC address to 9A:CA:D5:70:07:FD (scanning)

http://ix.io/3LTQ has not

You initally have a global connection, but are down to a local connection after 12 seconds:

Jan 11 18:01:54 ThinkPad-T420 NetworkManager[395]: <info>  [1641920514.7050] manager: NetworkManager state is now CONNECTED_GLOBAL
…
Jan 11 18:02:06 ThinkPad-T420 NetworkManager[395]: <info>  [1641920526.1892] manager: NetworkManager state is now CONNECTED_SITE

Notable events inbetween are that the sddm session stops and you're starting the portal service (for flatpak) - but there're no network events.

Please provide the outputs for the commands in #9 and I'd suggest to try to disable flatpak/portal first (post an updated journal if the issue remains) and then to skip sddm (try startx/xinit instead)

Offline

Board footer

Powered by FluxBB