You are not logged in.

#1 2022-12-15 20:32:59

smoneck
Member
Registered: 2014-05-14
Posts: 105

[RESOLVED] Dying SSD?

Hi!

Two days ago the CPU suddenly jumped to 100 % and the laptop (T480, almost always mounted below the table / not touched) froze.
After a couple of minutes of waiting I turned it off. Then it wouldnt boot for a while (staying at the Lenovo boot logo longer than I was patient).

Either the laptop or my patience decided otherwise and it finally booted again.
Now once in a while I get a 100 % CPU freeze-spike again for a few seconds but than it recovered (for now).

Within the log, I found:

Dec 15 21:15:40 hostname kernel: nvme nvme0: I/O 258 QID 1 timeout, reset controller
Dec 15 21:15:40 hostname kernel: nvme0n1: Read(0x2) @ LBA 588873392, 64 blocks, Host Aborted Command (sct 0x3 / sc 0x71)
Dec 15 21:15:40 hostname kernel: I/O error, dev nvme0n1, sector 588873392 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 2
Dec 15 21:15:40 hostname kernel: nvme0n1: Read(0x2) @ LBA 588873456, 256 blocks, Host Aborted Command (sct 0x3 / sc 0x71)
Dec 15 21:15:40 hostname kernel: I/O error, dev nvme0n1, sector 588873456 op 0x0:(READ) flags 0x80700 phys_seg 17 prio class 2
Dec 15 21:15:40 hostname kernel: nvme0n1: Read(0x2) @ LBA 55147552, 256 blocks, Host Aborted Command (sct 0x3 / sc 0x71)
Dec 15 21:15:40 hostname kernel: I/O error, dev nvme0n1, sector 55147552 op 0x0:(READ) flags 0x80700 phys_seg 31 prio class 2

I don't understand the s.m.a.r.t. output:

=== START OF SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

SMART/Health Information (NVMe Log 0x02)
Critical Warning:                   0x00
Temperature:                        31 Celsius
Available Spare:                    100%
Available Spare Threshold:          3%
Percentage Used:                    2%
Data Units Read:                    9,456,445 [4.84 TB]
Data Units Written:                 14,101,703 [7.22 TB]
Host Read Commands:                 132,334,354
Host Write Commands:                359,438,467
Controller Busy Time:               1,390
Power Cycles:                       2,638
Power On Hours:                     2,426
Unsafe Shutdowns:                   1,029
Media and Data Integrity Errors:    0
Error Information Log Entries:      545
Warning  Comp. Temperature Time:    0
Critical Comp. Temperature Time:    0
Temperature Sensor 1:               0 Celsius
Temperature Sensor 2:               31 Celsius
Temperature Sensor 3:               37 Celsius

Error Information (NVMe Log 0x01, 4 of 4 entries)
Num   ErrCount  SQId   CmdId  Status  PELoc          LBA  NSID    VS
  0        545     0  0xa003  0xc005  0x000            0     0     -
  1        544     0  0x0008  0xc005  0x000            0     0     -
  2        543     0  0x0011  0xc005  0x000            0     0     -
  3        542     0  0x0162  0xc004  0x000            0     0     -

All the bios quick-tests passed.

The question now is: Whats going on? Is my SSD dying?

Thanks a lot for any ideas!

Last edited by smoneck (2023-01-07 10:29:22)

Offline

#2 2022-12-16 03:12:33

cfr
Member
From: Cymru
Registered: 2011-11-27
Posts: 7,130

Re: [RESOLVED] Dying SSD?

Back up your data.

smoneck wrote:
Error Information Log Entries:      545
...
Error Information (NVMe Log 0x01, 4 of 4 entries)
Num   ErrCount  SQId   CmdId  Status  PELoc          LBA  NSID    VS
  0        545     0  0xa003  0xc005  0x000            0     0     -
  1        544     0  0x0008  0xc005  0x000            0     0     -
  2        543     0  0x0011  0xc005  0x000            0     0     -
  3        542     0  0x0162  0xc004  0x000            0     0     -

Some SSDs, including yours, provide minimal useful SMART data, but those errors are Not Good News. A healthy drive would log 0 errors. Yours has logged 545.

You also have a surprisingly high number of unsafe shutdowns relative to power-on hours and power cycles. However, I don't know how reliable that reading is for comparing results from different drives. It just looks rather high to me. In any case, that is a secondary issue. The errors are the only thing worth looking at in this output.

Last edited by cfr (2022-12-16 03:14:36)


CLI Paste | How To Ask Questions

Arch Linux | x86_64 | GPT | EFI boot | refind | stub loader | systemd | LVM2 on LUKS
Lenovo x270 | Intel(R) Core(TM) i5-7200U CPU @ 2.50GHz | Intel Wireless 8265/8275 | US keyboard w/ Euro | 512G NVMe INTEL SSDPEKKF512G7L

Offline

#3 2022-12-16 08:11:57

seth
Member
Registered: 2012-09-03
Posts: 49,992

Re: [RESOLVED] Dying SSD?

Not sure how to read your boot timeouts (ie. what was happening there, esp. if you preserve the vendor logo for a silent boot) but see https://wiki.archlinux.org/title/Solid_ … ST_support

Offline

#4 2022-12-17 11:12:51

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

cfr wrote:

Back up your data.

I have a backup but I have never been dependent on it. There are always the questions "Will it work?" and "Is it complete?".
Two questions I can just answer in hindsight.

cfr wrote:

Some SSDs, including yours, provide minimal useful SMART data, but those errors are Not Good News. A healthy drive would log 0 errors. Yours has logged 545.

One short hang apparently seems to increment each number by one. I guess that is not a good sign.

cfr wrote:

You also have a surprisingly high number of unsafe shutdowns relative to power-on hours and power cycles. However, I don't know how reliable that reading is for comparing results from different drives. It just looks rather high to me. In any case, that is a secondary issue. The errors are the only thing worth looking at in this output.

This seems to be realistic. The laptop often does not power off when it should. It then remains within some eternal limbus state spinning fan and sucking power.
(Fun fact: Before the firmware update it even did so appearing powered off but sucking the battery within half a day.)

I had a look at the SSD and it is so properly screwed in place that I can rule out any connectivity issues.

BUT there was some tape on the inside of the metal container that produced some grease(?) that also now sticks on the SSD.
I'm not sure what the purpose of this strip is (thermal or shock moderation) but that's something I need to tackle when swapping the drive.

https://i.imgur.com/DB2g0js.jpeg
https://i.imgur.com/8GNDW9l.jpeg


Mod Edit - Replaced oversized images with links.
CoC - Pasting pictures and code

Last edited by Slithery (2022-12-17 11:38:28)

Offline

#5 2022-12-17 14:10:37

seth
Member
Registered: 2012-09-03
Posts: 49,992

Re: [RESOLVED] Dying SSD?

Edit: looks like a heatpad to avoid an air cushion between the dies and the case (still air is a great isolator that will keep the dies neatly warm … until they boil)
The fact that it has molten (at least from what I can tell from the photo) tells you that there was some serious local heat.
Re-install it as good as you can.

Last edited by seth (2022-12-17 14:13:41)

Offline

#6 2022-12-18 00:47:53

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

First of all thank you for all the feedback so far!

seth wrote:

The fact that it has molten (at least from what I can tell from the photo) tells you that there was some serious local heat.

Shouldn't there be a thermal throttling? I was wondering if maybe simply the plastic was breaking down and releasing the plasticizers.

In particular, given the context of the thermal pad, I'll slowly move up the state scale as 6.50W in my case is pretty much power in those chips.
But seeing the s.m.a.r.t. values rise with every hang, I meanwhile doubt that it is possible to be a driver issue.

Offline

#7 2022-12-18 02:00:34

cfr
Member
From: Cymru
Registered: 2011-11-27
Posts: 7,130

Re: [RESOLVED] Dying SSD?

smoneck wrote:

But seeing the s.m.a.r.t. values rise with every hang, I meanwhile doubt that it is possible to be a driver issue.

Might you get that from the bug seth mentioned? It would be worth adding

nvme_core.default_ps_max_latency_us=0

to your kernel parameters and seeing if that (1) stops the hangs and (2) stops the errors rising in the SMART data.

However, if this is a new issue (as your first post seemed to indicate) and it worked fine before, it may be less likely. But I would still try the parameter. I just wouldn't trust the drive meanwhile with anything you don't have backed up.


CLI Paste | How To Ask Questions

Arch Linux | x86_64 | GPT | EFI boot | refind | stub loader | systemd | LVM2 on LUKS
Lenovo x270 | Intel(R) Core(TM) i5-7200U CPU @ 2.50GHz | Intel Wireless 8265/8275 | US keyboard w/ Euro | 512G NVMe INTEL SSDPEKKF512G7L

Offline

#8 2022-12-18 08:57:16

seth
Member
Registered: 2012-09-03
Posts: 49,992

Re: [RESOLVED] Dying SSD?

I was wondering if maybe simply the plastic was breaking down and releasing the plasticizers.

Is the pad cushy/bouncy/springy and maybe somewhat sticky or just hard plastic?

Offline

#9 2022-12-18 14:20:59

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

seth wrote:

I was wondering if maybe simply the plastic was breaking down and releasing the plasticizers.

Is the pad cushy/bouncy/springy and maybe somewhat sticky or just hard plastic?

Soft, cushy and sticky.

cfr wrote:

Might you get that from the bug seth mentioned?

Just my gut feeling. From my understanding / "feeling", internal device error values should be independent on external connectivity issues. That should go one step up to the next abstraction level.

cfr wrote:

It would be worth adding

nvme_core.default_ps_max_latency_us=0

to your kernel parameters and seeing if that (1) stops the hangs and (2) stops the errors rising in the SMART data.

I was reluctant since that -- according to the smartctl-output -- means dissipating 6.5 W on the chip on the background of a possible heat problem.
But I now added it anyway. Now I found the following:

Dec 18 15:02:33 hostname kernel: nvme nvme0: I/O 364 (Read) QID 1 timeout, aborting
Dec 18 15:02:44 hostname kernel: nvme nvme0: I/O 269 (Read) QID 3 timeout, aborting
Dec 18 15:02:44 hostname kernel: nvme nvme0: I/O 270 (Read) QID 3 timeout, aborting
Dec 18 15:02:44 hostname kernel: nvme nvme0: I/O 271 (Read) QID 3 timeout, aborting
Dec 18 15:02:44 hostname kernel: nvme nvme0: Abort status: 0x0
Dec 18 15:02:44 hostname kernel: nvme nvme0: Abort status: 0x0
Dec 18 15:02:44 hostname kernel: nvme nvme0: Abort status: 0x0
Dec 18 15:02:44 hostname kernel: nvme nvme0: Abort status: 0x0
Dec 18 15:03:03 hostname kernel: nvme nvme0: I/O 364 QID 1 timeout, reset controller
Dec 18 15:03:03 hostname kernel: nvme0n1: Read(0x2) @ LBA 34638848, 32 blocks, Host Aborted Command (sct 0x3 / sc 0x71)
Dec 18 15:03:03 hostname kernel: I/O error, dev nvme0n1, sector 34638848 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
Dec 18 15:03:03 hostname kernel: nvme0n1: Read(0x2) @ LBA 34638888, 8 blocks, Host Aborted Command (sct 0x3 / sc 0x71)
Dec 18 15:03:03 hostname kernel: I/O error, dev nvme0n1, sector 34638888 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
Dec 18 15:03:03 hostname kernel: nvme0n1: Read(0x2) @ LBA 34638904, 16 blocks, Host Aborted Command (sct 0x3 / sc 0x71)
Dec 18 15:03:03 hostname kernel: I/O error, dev nvme0n1, sector 34638904 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
Dec 18 15:03:04 hostname kernel: nvme nvme0: failed to set APST feature (16386)
Dec 18 15:03:04 hostname kernel: nvme nvme0: 8/0/0 default/read/poll queues

Offline

#10 2022-12-18 14:50:05

seth
Member
Registered: 2012-09-03
Posts: 49,992

Re: [RESOLVED] Dying SSD?

Soft, cushy and sticky.

That's a heat pad - it's hopefully back in place and somewhat sticks to the chip that has (had) the gunk on it?

Theoretically these pads are not re-usable, but it's certainly better than nothing.

On the OP - does it help if you blow a lot of cold air against the NVME?
Is it maybe unfortunately placed in the heat radiation of other HW (eg. GPU and CPU will get MUCH hotter than is good for an NVME and in the worst case scenario, case and heatpad add to the chip temperature)

Offline

#11 2022-12-18 15:05:03

cfr
Member
From: Cymru
Registered: 2011-11-27
Posts: 7,130

Re: [RESOLVED] Dying SSD?

smoneck wrote:

Just my gut feeling. From my understanding / "feeling", internal device error values should be independent on external connectivity issues. That should go one step up to the next abstraction level.

That's what I thought, too, but I'm not confident I understand how SMART works with nvme devices (even though I'm using one).

Dec 18 15:02:33 hostname kernel: nvme nvme0: I/O 364 (Read) QID 1 timeout, aborting
Dec 18 15:02:44 hostname kernel: nvme nvme0: I/O 269 (Read) QID 3 timeout, aborting
Dec 18 15:02:44 hostname kernel: nvme nvme0: I/O 270 (Read) QID 3 timeout, aborting
Dec 18 15:02:44 hostname kernel: nvme nvme0: I/O 271 (Read) QID 3 timeout, aborting
Dec 18 15:02:44 hostname kernel: nvme nvme0: Abort status: 0x0
Dec 18 15:02:44 hostname kernel: nvme nvme0: Abort status: 0x0
Dec 18 15:02:44 hostname kernel: nvme nvme0: Abort status: 0x0
Dec 18 15:02:44 hostname kernel: nvme nvme0: Abort status: 0x0
Dec 18 15:03:03 hostname kernel: nvme nvme0: I/O 364 QID 1 timeout, reset controller
Dec 18 15:03:03 hostname kernel: nvme0n1: Read(0x2) @ LBA 34638848, 32 blocks, Host Aborted Command (sct 0x3 / sc 0x71)
Dec 18 15:03:03 hostname kernel: I/O error, dev nvme0n1, sector 34638848 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 2
Dec 18 15:03:03 hostname kernel: nvme0n1: Read(0x2) @ LBA 34638888, 8 blocks, Host Aborted Command (sct 0x3 / sc 0x71)
Dec 18 15:03:03 hostname kernel: I/O error, dev nvme0n1, sector 34638888 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 2
Dec 18 15:03:03 hostname kernel: nvme0n1: Read(0x2) @ LBA 34638904, 16 blocks, Host Aborted Command (sct 0x3 / sc 0x71)
Dec 18 15:03:03 hostname kernel: I/O error, dev nvme0n1, sector 34638904 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 2
Dec 18 15:03:04 hostname kernel: nvme nvme0: failed to set APST feature (16386)
Dec 18 15:03:04 hostname kernel: nvme nvme0: 8/0/0 default/read/poll queues

sad


CLI Paste | How To Ask Questions

Arch Linux | x86_64 | GPT | EFI boot | refind | stub loader | systemd | LVM2 on LUKS
Lenovo x270 | Intel(R) Core(TM) i5-7200U CPU @ 2.50GHz | Intel Wireless 8265/8275 | US keyboard w/ Euro | 512G NVMe INTEL SSDPEKKF512G7L

Offline

#12 2022-12-18 15:43:59

seth
Member
Registered: 2012-09-03
Posts: 49,992

Re: [RESOLVED] Dying SSD?

Afaiu the latency issue it induces an actual controller failure (ie. this is not a problem in the kernel or the bus, but in the nvme) and would expect that to get logged by the device.

Dec 18 15:03:04 hostname kernel: nvme nvme0: failed to set APST feature (16386)

Are we sure the parameter has been applied?
How?

cat /proc/cmdline

Offline

#13 2022-12-18 15:56:11

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

seth wrote:

How?

cat /proc/cmdline
BOOT_IMAGE=/vmlinuz-linux root=/dev/mapper/vg0-arch rw cryptdevice=/dev/nvme0n1p2:luks:allow-discards psmouse.synaptics_intertouch=0 modprobe.blacklist=nouveau i915.enable_psr=1 iwlwifi.power_save=Y iwldvm.force_cam=N i915.enable_fbc=1 nvme_core.default_ps_max_latency_us=0 pcie_aspm=off loglevel=3 quiet

Offline

#14 2022-12-18 16:04:55

seth
Member
Registered: 2012-09-03
Posts: 49,992

Re: [RESOLVED] Dying SSD?

So unfortunately "yes", is "pcie_aspm=off" a mitigational effort or for different reasons?

Offline

#15 2022-12-18 16:05:42

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

This is a similar version:

The metal case on the bottom left:
Lenovo-ThinkPad-T480-Review-21.jpg

and opened up:
Lenovo-ThinkPad-T480-Review-22.jpg

seth wrote:

That's a heat pad - it's hopefully back in place and somewhat sticks to the chip that has (had) the gunk on it?

Yeah, it sticks to the metal, not the chip. So it should be as it was before.

seth wrote:

Is it maybe unfortunately placed in the heat radiation of other HW (eg. GPU and CPU will get MUCH hotter than is good for an NVME and in the worst case scenario, case and heatpad add to the chip temperature)

To my muggle eyes, the thermal construction looks good.

Offline

#16 2022-12-18 16:13:24

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

seth wrote:

So unfortunately "yes", is "pcie_aspm=off" a mitigational effort or for different reasons?

I added it as a try to handle this very message as we wanted to disable power-management anyway. It's removed now and ... so far no message anymore. Aha. Hm

Offline

#17 2022-12-18 16:53:53

cfr
Member
From: Cymru
Registered: 2011-11-27
Posts: 7,130

Re: [RESOLVED] Dying SSD?

So is the SMART error count no longer increasing?


CLI Paste | How To Ask Questions

Arch Linux | x86_64 | GPT | EFI boot | refind | stub loader | systemd | LVM2 on LUKS
Lenovo x270 | Intel(R) Core(TM) i5-7200U CPU @ 2.50GHz | Intel Wireless 8265/8275 | US keyboard w/ Euro | 512G NVMe INTEL SSDPEKKF512G7L

Offline

#18 2022-12-18 17:18:39

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

cfr wrote:

So is the SMART error count no longer increasing?

It's too early to say that. It used to be +1 or +2 a day. For the record, the current state is:

Num   ErrCount  SQId   CmdId  Status  PELoc          LBA  NSID    VS
  0        554     0  0x5011  0xc005  0x000            0     0     -
  1        553     0  0x000c  0xc005  0x000            0     0     -
  2        552     0  0xf001  0xc005  0x000            0     0     -
  3        551     0  0x5001  0xc005  0x000            0     0     -

I'll now follow it closely and report back.

Offline

#19 2022-12-27 18:33:16

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

smoneck wrote:

I'll now follow it closely and report back.

I haven't been using this computer much since then and no more errors appeared within the journal but the s.m.a.r.t. errors appear to keep rising.

Num   ErrCount  SQId   CmdId  Status  PELoc          LBA  NSID    VS
  0        561     0  0x5018  0xc005  0x000            0     0     -
  1        560     0  0x400f  0xc005  0x000            0     0     -
  2        559     0  0x0000  0xc005  0x000            0     0     -
  3        558     0  0x0005  0xc005  0x000            0     0     -

Last edited by smoneck (2022-12-27 18:33:52)

Offline

#20 2022-12-27 20:50:37

seth
Member
Registered: 2012-09-03
Posts: 49,992

Re: [RESOLVED] Dying SSD?

nvme_core.default_ps_max_latency_us=0 is still in place?
Have you checked the temperature of the nvme under some overall system load? (cpu, gpu and nvme)

Offline

#21 2022-12-27 22:27:27

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

seth wrote:

nvme_core.default_ps_max_latency_us=0 is still in place?
Have you checked the temperature of the nvme under some overall system load? (cpu, gpu and nvme)

nvme_core.default_ps_max_latency_us=0 is still in place and I haven't experienced any hick-ups anymore.

So far, the temperature looks good but I can't say anything about workloads at the moment as I was just doing light vim-typing.

Temperature Sensor 1           : 46°C (319 Kelvin)
Temperature Sensor 2           : 37°C (310 Kelvin)
Temperature Sensor 3           : 37°C (310 Kelvin)

Judging from the inside of the laptop, it looks well enough constructed to me that cpu / gpu heat should not be an issue.

I'm gonna work from home tomorrow and I started logging the temperature sensors every minute.

Let's see, what comes out of it ... :-)

Last edited by smoneck (2022-12-27 22:27:52)

Offline

#22 2022-12-28 08:00:48

seth
Member
Registered: 2012-09-03
Posts: 49,992

Re: [RESOLVED] Dying SSD?

I haven't experienced any hick-ups anymore.

The nvme errors may be meaningless, https://www.smartmontools.org/wiki/NVMe_Support (look at the bottom example)

Offline

#23 2023-01-07 10:25:47

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

seth wrote:

The nvme errors may be meaningless, https://www.smartmontools.org/wiki/NVMe_Support (look at the bottom example)

I'm not sure what you're basing that on.

The man-page of smartctl states

error - [ATA] prints the Summary SMART error log.  SMART disks maintain a log of the most recent five non-trivial  er‐
rors.   For each of these errors, the disk power-on lifetime at which the error occurred is recorded, as is the device
status (idle, standby, etc) at the time of the error.  For some common types of errors, the Error  Register  (ER)  and 
Status Register (SR) values are decoded and printed as text.  The meanings of these are:
[...]
In addition, up to the last five commands that preceded the error are listed, along with a timestamp measured from the 
start of the corresponding power cycle.

I therefore suspect that in the example simply the last N errors are logged without any further information about their severity / type.

ESpg4F3.jpeg

I have now looked at the history of temperature (sensors exposed in /sys/class/nvme/nvme0) and errors over the last few days. The vertical lines in gray mark the boots.

1) I do not see any critical temperatures (okay, we have winter here ...) - i.e. I guess the pad is leaking plasticizers.

2) The error counter seems to behave identically to the boot counts, and I can't see the times in the data where I turned it off hard (because it wasn't powering off porperly). I still have no idea what the counter means but in the meantime I am reasonably reassured that it is nothing serious. However, the next two months I have so much to do that I won't get to play with the mentioned qemu-fork.

Since adding `nvme_core.default_ps_max_latency_us=0` I haven't had any more problems with hangers and the battery consumption doesn't seem to have increased dramatically either.

Thank you so much for your support!

Last edited by smoneck (2023-01-07 10:34:23)

Offline

#24 2023-01-07 10:41:55

seth
Member
Registered: 2012-09-03
Posts: 49,992

Re: [RESOLVED] Dying SSD?

seth wrote:

The nvme errors may be meaningless

Those "errors" are common and all over the place and not necessarily an indicator for problems.
https://archlinux.org/packages/communit … /nvme-cli/ might provide better insight.

sudo nvme error-log /dev/nvme0

Offline

#25 2023-01-07 11:11:37

smoneck
Member
Registered: 2014-05-14
Posts: 105

Re: [RESOLVED] Dying SSD?

seth wrote:
sudo nvme error-log /dev/nvme0

No new insights for me. hmm

> sudo nvme error-log /dev/nvme0 | rg 'error_count|status_field'
error_count	: 573
status_field	: 0x6002(Invalid Field in Command: A reserved coded value or an unsupported value in a defined field)
error_count	: 572
status_field	: 0x6002(Invalid Field in Command: A reserved coded value or an unsupported value in a defined field)
error_count	: 571
status_field	: 0x6002(Invalid Field in Command: A reserved coded value or an unsupported value in a defined field)
error_count	: 570
status_field	: 0x6002(Invalid Field in Command: A reserved coded value or an unsupported value in a defined field)

Offline

Board footer

Powered by FluxBB