You are not logged in.
- Topics: Active | Unanswered
#26 2024-04-24 17:12:31
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
Output from xrandr -q
[leessmin@r97945hx ~]$ xrandr -q
Screen 0: minimum 8 x 8, current 2560 x 1600, maximum 32767 x 32767
HDMI-0 disconnected (normal left inverted right x axis y axis)
DP-0 connected primary 2560x1600+0+0 (normal left inverted right x axis y axis) 345mm x 215mm
2560x1600 60.00*+ 240.00
eDP-1-2 disconnected (normal left inverted right x axis y axis)
DP-1-1 disconnected (normal left inverted right x axis y axis)
DP-1-2 disconnected (normal left inverted right x axis y axis)
DP-1-3 disconnected (normal left inverted right x axis y axis)[leessmin@r97945hx ~]$ ls /sys/class/drm/card*
/sys/class/drm/card0:
card0-eDP-1 card0-HDMI-A-1 dev device power subsystem uevent
/sys/class/drm/card0-eDP-1:
connector_id device dpms edid enabled modes power status subsystem uevent
/sys/class/drm/card0-HDMI-A-1:
connector_id device dpms edid enabled modes power status subsystem uevent
/sys/class/drm/card1:
card1-DP-1 card1-DP-2 card1-DP-3 card1-eDP-2 card1-Writeback-1 dev device power subsystem uevent
/sys/class/drm/card1-DP-1:
connector_id ddc device dpms drm_dp_aux1 edid enabled i2c-14 modes power status subsystem uevent
/sys/class/drm/card1-DP-2:
connector_id ddc device dpms drm_dp_aux2 edid enabled i2c-15 modes power status subsystem uevent
/sys/class/drm/card1-DP-3:
connector_id ddc device dpms drm_dp_aux3 edid enabled i2c-16 modes power status subsystem uevent
/sys/class/drm/card1-eDP-2:
connector_id ddc device dpms drm_dp_aux0 edid enabled i2c-13 modes power status subsystem uevent
/sys/class/drm/card1-Writeback-1:
connector_id device dpms edid enabled modes power status subsystem ueventhttps://aur.archlinux.org/packages/edid-decode ? It looks like it requires aur, I can't quite guarantee that my current environment will be able to install it because my current internet environment sometimes can't access offshore sites, I'll try it out
Offline
#27 2024-04-24 17:20:25
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
seth wrote:
You'll need https://aur.archlinux.org/packages/edid-decode-git for the latter.
I have edid-decode-git installed, but how do I use it?
Offline
#28 2024-04-24 17:20:46
- seth
- Member
- Registered: 2012-09-03
- Posts: 51,684
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
Please post your Xorg log, https://wiki.archlinux.org/title/Xorg#General - the relevant edid is ideally inside that as well.
You also on X11 cannot
xrandr --output DP-0 --rate 240?
Edit: run the while loop I posted before, it'll print the edid's of all available outputs (only one)
Last edited by seth (2024-04-24 17:21:34)
Offline
#29 2024-04-24 17:23:18
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
[leessmin@r97945hx yay]$ xrandr --output DP-0 --rate 240
[leessmin@r97945hx yay]$ xrandr --output DP-0 --rate 240This print has no output
Offline
#30 2024-04-24 17:25:29
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
Sorry, I just now realized what you meant, here's the printout
for OUT in /sys/class/drm/card*; do echo $OUT; edid-decode $OUT/edid; echo "================="; done
/sys/class/drm/card0
/sys/class/drm/card0/edid: No such file or directory
=================
/sys/class/drm/card0-eDP-1
edid-decode (hex):
00 ff ff ff ff ff ff 00 51 b8 01 16 00 00 00 00
1e 1f 01 04 b5 23 16 78 07 8a 21 a4 53 4c 99 25
10 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 0d 6f 00 a0 a0 40 8e 60 30 20
36 00 59 d7 10 00 00 1a 00 00 00 fd 0c 3c f0 8b
8b 72 01 0a 20 20 20 20 20 20 00 00 00 10 0c 30
f0 50 50 43 00 0a 20 20 20 20 20 20 00 00 00 fc
00 54 4c 31 36 30 41 44 4d 50 31 31 2d 30 02 76
02 03 1f 00 e3 05 80 00 e6 06 07 01 6a 6a 23 72
1a 00 00 03 0b 30 f0 00 04 6a 23 6a 23 f0 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 18 a9
70 13 79 00 00 03 01 14 34 bc 01 84 ff 09 9f 00
2f 00 1f 00 3f 06 8d 00 02 00 05 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 19 90
----------------
Block 0, Base EDID:
EDID Structure Version & Revision: 1.4
Vendor & Product Identification:
Manufacturer: TMX
Model: 5633
Made in: week 30 of 2021
Basic Display Parameters & Features:
Digital display
Bits per primary color channel: 10
DisplayPort interface
Maximum image size: 35 cm x 22 cm
Gamma: 2.20
Supported color formats: RGB 4:4:4
Default (sRGB) color space is primary color space
First detailed timing includes the native pixel format and preferred refresh rate
Display supports continuous frequencies
Color Characteristics:
Red : 0.6425, 0.3242
Green: 0.2988, 0.5996
Blue : 0.1445, 0.0644
White: 0.3125, 0.3291
Established Timings I & II: none
Standard Timings: none
Detailed Timing Descriptors:
DTD 1: 2560x1600 59.999071 Hz 16:10 104.518 kHz 284.290000 MHz (345 mm x 215 mm)
Hfront 48 Hsync 32 Hback 80 Hpol P
Vfront 3 Vsync 6 Vback 133 Vpol N
Display Range Limits:
Monitor ranges (Range Limits Only): 60-240 Hz V, 394-394 kHz H, max dotclock 1140 MHz
Dummy Descriptor:
Display Product Name: 'TL160ADMP11-0'
Extension blocks: 2
Checksum: 0x76
----------------
Block 1, CTA-861 Extension Block:
Revision: 3
Native detailed modes: 0
Colorimetry Data Block:
BT2020RGB
HDR Static Metadata Data Block:
Electro optical transfer functions:
Traditional gamma - SDR luminance range
Traditional gamma - HDR luminance range
SMPTE ST2084
Supported static metadata descriptors:
Static metadata type 1
Desired content max luminance: 106 (496.743 cd/m^2)
Desired content max frame-average luminance: 106 (496.743 cd/m^2)
Desired content min luminance: 35 (0.094 cd/m^2)
Vendor-Specific Data Block (AMD), OUI 00-00-1A:
Version: 3.11
Minimum Refresh Rate: 48 Hz
Maximum Refresh Rate: 240 Hz
Flags 1.x: 0x00
Flags 2.x: 0x04
Maximum luminance: 106 (496.743 cd/m^2)
Minimum luminance: 35 (0.094 cd/m^2)
Maximum luminance (without local dimming): 106 (496.743 cd/m^2)
Minimum luminance (without local dimming): 35 (0.094 cd/m^2)
Checksum: 0xa9 Unused space in Extension Block: 96 bytes
----------------
Block 2, DisplayID Extension Block:
Version: 1.3
Extension Count: 0
Display Product Type: Extension Section
Video Timing Modes Type 1 - Detailed Timings Data Block:
DTD: 2560x1600 239.998396 Hz 16:9 418.077 kHz 1137.170000 MHz (aspect 16:9, no 3D stereo, preferred)
Hfront 48 Hsync 32 Hback 80 Hpol N
Vfront 3 Vsync 6 Vback 133 Vpol N
Checksum: 0x19
Checksum: 0x90
=================
/sys/class/drm/card0-HDMI-A-1
EDID of '/sys/class/drm/card0-HDMI-A-1/edid' was empty.
=================
/sys/class/drm/card1
/sys/class/drm/card1/edid: No such file or directory
=================
/sys/class/drm/card1-DP-1
EDID of '/sys/class/drm/card1-DP-1/edid' was empty.
=================
/sys/class/drm/card1-DP-2
EDID of '/sys/class/drm/card1-DP-2/edid' was empty.
=================
/sys/class/drm/card1-DP-3
EDID of '/sys/class/drm/card1-DP-3/edid' was empty.
=================
/sys/class/drm/card1-eDP-2
EDID of '/sys/class/drm/card1-eDP-2/edid' was empty.
=================
/sys/class/drm/card1-Writeback-1
EDID of '/sys/class/drm/card1-Writeback-1/edid' was empty.
=================Offline
#31 2024-04-24 17:30:31
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
Turning on 240hz in an x11 environment does the same thing as encountering it in wayland
Offline
#32 2024-04-24 21:26:34
- seth
- Member
- Registered: 2012-09-03
- Posts: 51,684
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
Display supports continuous frequencieshttps://wiki.archlinux.org/title/Variab … _on_NVIDIA
Ftr, monitor showed up in https://bbs.archlinux.org/viewtopic.php?id=283229 - apparently working at 240HZ w/ nvidia only but you'ree running on that chip anyway.
Can you disable the AMD chip in the BIOS/UEFI?
Offline
#33 2024-04-24 23:35:48
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
I have always used Nvidia Direct connection mode, and have not used amd Gpus
Offline
#34 2024-04-25 08:16:25
- seth
- Member
- Registered: 2012-09-03
- Posts: 51,684
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
The AMD GPU is still in the journal, ie the system is running in hybrid mode.
Please post your Xorg log, https://wiki.archlinux.org/title/Xorg#General and try to disable the IGP/AMD GPU in the BIOS/UEFI.
Offline
#35 2024-04-25 09:22:03
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
cat /var/log/Xorg.0.log
[ 9.219] (--) Log file renamed from "/var/log/Xorg.pid-1030.log" to "/var/log/Xorg.0.log"
[ 9.219]
X.Org X Server 1.21.1.13
X Protocol Version 11, Revision 0
[ 9.219] Current Operating System: Linux r97945hx 6.8.7-arch1-1 #1 SMP PREEMPT_DYNAMIC Wed, 17 Apr 2024 15:20:28 +0000 x86_64
[ 9.219] Kernel command line: initrd=\amd-ucode.img initrd=\initramfs-linux.img root=PARTUUID=759e0ffe-2d9c-4cd0-a30a-ed9a273d9284 zswap.enabled=0 rootflags=subvol=@ rw rootfstype=btrfs
[ 9.219]
[ 9.219] Current version of pixman: 0.43.4
[ 9.219] Before reporting problems, check http://wiki.x.org
to make sure that you have the latest version.
[ 9.219] Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
[ 9.219] (==) Log file: "/var/log/Xorg.0.log", Time: Thu Apr 25 17:18:59 2024
[ 9.219] (==) Using config directory: "/etc/X11/xorg.conf.d"
[ 9.219] (==) Using system config directory "/usr/share/X11/xorg.conf.d"
[ 9.219] (==) No Layout section. Using the first Screen section.
[ 9.219] (==) No screen section available. Using defaults.
[ 9.219] (**) |-->Screen "Default Screen Section" (0)
[ 9.219] (**) | |-->Monitor "<default monitor>"
[ 9.219] (==) No monitor specified for screen "Default Screen Section".
Using a default monitor configuration.
[ 9.219] (**) Allowing byte-swapped clients
[ 9.219] (==) Automatically adding devices
[ 9.219] (==) Automatically enabling devices
[ 9.219] (==) Automatically adding GPU devices
[ 9.219] (==) Automatically binding GPU devices
[ 9.219] (==) Max clients allowed: 256, resource mask: 0x1fffff
[ 9.219] (WW) The directory "/usr/share/fonts/misc" does not exist.
[ 9.219] Entry deleted from font path.
[ 9.220] (WW) `fonts.dir' not found (or not valid) in "/usr/share/fonts/TTF".
[ 9.220] Entry deleted from font path.
[ 9.220] (Run 'mkfontdir' on "/usr/share/fonts/TTF").
[ 9.220] (WW) The directory "/usr/share/fonts/OTF" does not exist.
[ 9.220] Entry deleted from font path.
[ 9.220] (WW) The directory "/usr/share/fonts/Type1" does not exist.
[ 9.220] Entry deleted from font path.
[ 9.220] (WW) The directory "/usr/share/fonts/100dpi" does not exist.
[ 9.220] Entry deleted from font path.
[ 9.220] (WW) The directory "/usr/share/fonts/75dpi" does not exist.
[ 9.220] Entry deleted from font path.
[ 9.220] (==) FontPath set to:
[ 9.220] (==) ModulePath set to "/usr/lib/xorg/modules"
[ 9.220] (II) The server relies on udev to provide the list of input devices.
If no devices become available, reconfigure udev or disable AutoAddDevices.
[ 9.220] (II) Module ABI versions:
[ 9.220] X.Org ANSI C Emulation: 0.4
[ 9.220] X.Org Video Driver: 25.2
[ 9.220] X.Org XInput driver : 24.4
[ 9.220] X.Org Server Extension : 10.0
[ 9.220] (++) using VT number 2
[ 9.220] (II) systemd-logind: logind integration requires -keeptty and -keeptty was not provided, disabling logind integration
[ 9.221] (II) xfree86: Adding drm device (/dev/dri/card1)
[ 9.221] (II) Platform probe for /sys/devices/pci0000:00/0000:00:01.1/0000:01:00.0/drm/card1
[ 9.221] (II) xfree86: Adding drm device (/dev/dri/card2)
[ 9.221] (II) Platform probe for /sys/devices/pci0000:00/0000:00:08.1/0000:06:00.0/drm/card2
[ 9.222] (II) xfree86: Adding drm device (/dev/dri/card0)
[ 9.222] (II) Platform probe for /sys/devices/platform/simple-framebuffer.0/drm/card0
[ 9.224] (**) OutputClass "nvidia" ModulePath extended to "/usr/lib/nvidia/xorg,/usr/lib/xorg/modules,/usr/lib/xorg/modules"
[ 9.226] (--) PCI:*(1@0:0:0) 10de:28a0:1d05:1302 rev 161, Mem @ 0xc0000000/16777216, 0x3ffa00000000/8589934592, 0x3ffc00000000/33554432, I/O @ 0x00003000/128, BIOS @ 0x????????/524288
[ 9.226] (--) PCI: (6@0:0:0) 1002:164e:1d05:1301 rev 216, Mem @ 0x3ffc10000000/268435456, 0x3ffc20000000/2097152, 0xc1500000/524288, I/O @ 0x00001000/256
[ 9.226] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
[ 9.226] (II) LoadModule: "glx"
[ 9.226] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
[ 9.227] (II) Module glx: vendor="X.Org Foundation"
[ 9.227] compiled for 1.21.1.13, module version = 1.0.0
[ 9.227] ABI class: X.Org Server Extension, version 10.0
[ 9.227] (II) Applying OutputClass "nvidia" to /dev/dri/card1
[ 9.227] loading driver: nvidia
[ 9.227] (==) Matched nvidia as autoconfigured driver 0
[ 9.227] (==) Matched nouveau as autoconfigured driver 1
[ 9.227] (==) Matched nv as autoconfigured driver 2
[ 9.227] (==) Matched ati as autoconfigured driver 3
[ 9.227] (==) Matched modesetting as autoconfigured driver 4
[ 9.227] (==) Matched fbdev as autoconfigured driver 5
[ 9.227] (==) Matched vesa as autoconfigured driver 6
[ 9.227] (==) Assigned the driver to the xf86ConfigLayout
[ 9.227] (II) LoadModule: "nvidia"
[ 9.227] (II) Loading /usr/lib/xorg/modules/drivers/nvidia_drv.so
[ 9.227] (II) Module nvidia: vendor="NVIDIA Corporation"
[ 9.227] compiled for 1.6.99.901, module version = 1.0.0
[ 9.227] Module class: X.Org Video Driver
[ 9.227] (II) LoadModule: "nouveau"
[ 9.227] (WW) Warning, couldn't open module nouveau
[ 9.227] (EE) Failed to load module "nouveau" (module does not exist, 0)
[ 9.227] (II) LoadModule: "nv"
[ 9.227] (WW) Warning, couldn't open module nv
[ 9.227] (EE) Failed to load module "nv" (module does not exist, 0)
[ 9.227] (II) LoadModule: "ati"
[ 9.227] (WW) Warning, couldn't open module ati
[ 9.227] (EE) Failed to load module "ati" (module does not exist, 0)
[ 9.227] (II) LoadModule: "modesetting"
[ 9.227] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so
[ 9.228] (II) Module modesetting: vendor="X.Org Foundation"
[ 9.228] compiled for 1.21.1.13, module version = 1.21.1
[ 9.228] Module class: X.Org Video Driver
[ 9.228] ABI class: X.Org Video Driver, version 25.2
[ 9.228] (II) LoadModule: "fbdev"
[ 9.228] (WW) Warning, couldn't open module fbdev
[ 9.228] (EE) Failed to load module "fbdev" (module does not exist, 0)
[ 9.228] (II) LoadModule: "vesa"
[ 9.228] (WW) Warning, couldn't open module vesa
[ 9.228] (EE) Failed to load module "vesa" (module does not exist, 0)
[ 9.228] (II) NVIDIA dlloader X Driver 550.76 Wed Apr 10 20:08:05 UTC 2024
[ 9.228] (II) NVIDIA Unified Driver for all Supported NVIDIA GPUs
[ 9.228] (II) modesetting: Driver for Modesetting Kernel Drivers: kms
[ 9.231] (II) Loading sub module "fb"
[ 9.231] (II) LoadModule: "fb"
[ 9.231] (II) Module "fb" already built-in
[ 9.231] (II) Loading sub module "wfb"
[ 9.231] (II) LoadModule: "wfb"
[ 9.232] (II) Loading /usr/lib/xorg/modules/libwfb.so
[ 9.232] (II) Module wfb: vendor="X.Org Foundation"
[ 9.232] compiled for 1.21.1.13, module version = 1.0.0
[ 9.232] ABI class: X.Org ANSI C Emulation, version 0.4
[ 9.232] (WW) Falling back to old probe method for modesetting
[ 9.235] (II) modeset(G0): using drv /dev/dri/card2
[ 9.237] (II) modeset(G1): using drv /dev/dri/card0
[ 9.237] (II) NVIDIA(0): Creating default Display subsection in Screen section
"Default Screen Section" for depth/fbbpp 24/32
[ 9.237] (==) NVIDIA(0): Depth 24, (==) framebuffer bpp 32
[ 9.237] (==) NVIDIA(0): RGB weight 888
[ 9.237] (==) NVIDIA(0): Default visual is TrueColor
[ 9.237] (==) NVIDIA(0): Using gamma correction (1.0, 1.0, 1.0)
[ 9.237] (II) Applying OutputClass "nvidia" options to /dev/dri/card1
[ 9.237] (**) NVIDIA(0): Option "AllowEmptyInitialConfiguration"
[ 9.237] (**) NVIDIA(0): Enabling 2D acceleration
[ 9.237] (II) Loading sub module "glxserver_nvidia"
[ 9.237] (II) LoadModule: "glxserver_nvidia"
[ 9.237] (II) Loading /usr/lib/nvidia/xorg/libglxserver_nvidia.so
[ 9.243] (II) Module glxserver_nvidia: vendor="NVIDIA Corporation"
[ 9.243] compiled for 1.6.99.901, module version = 1.0.0
[ 9.243] Module class: X.Org Server Extension
[ 9.243] (II) NVIDIA GLX Module 550.76 Wed Apr 10 20:08:09 UTC 2024
[ 9.243] (II) NVIDIA: The X server supports PRIME Render Offload.
[ 9.243] (--) NVIDIA(0): Valid display device(s) on GPU-0 at PCI:1:0:0
[ 9.243] (--) NVIDIA(0): DFP-0
[ 9.243] (--) NVIDIA(0): DFP-1 (boot)
[ 9.244] (II) NVIDIA(0): NVIDIA GPU NVIDIA GeForce RTX 4060 Laptop GPU (AD107-A) at
[ 9.244] (II) NVIDIA(0): PCI:1:0:0 (GPU-0)
[ 9.244] (--) NVIDIA(0): Memory: 8384512 kBytes
[ 9.244] (--) NVIDIA(0): VideoBIOS: 95.07.21.00.24
[ 9.244] (II) NVIDIA(0): Detected PCI Express Link width: 8X
[ 9.244] (--) NVIDIA(GPU-0): DFP-0: disconnected
[ 9.244] (--) NVIDIA(GPU-0): DFP-0: Internal TMDS
[ 9.244] (--) NVIDIA(GPU-0): DFP-0: 165.0 MHz maximum pixel clock
[ 9.244] (--) NVIDIA(GPU-0):
[ 9.244] (--) NVIDIA(GPU-0): TMX TL160ADMP11-0 (DFP-1): connected
[ 9.244] (--) NVIDIA(GPU-0): TMX TL160ADMP11-0 (DFP-1): Internal DisplayPort
[ 9.244] (--) NVIDIA(GPU-0): TMX TL160ADMP11-0 (DFP-1): 2670.0 MHz maximum pixel clock
[ 9.244] (--) NVIDIA(GPU-0):
[ 9.245] (==) NVIDIA(0):
[ 9.245] (==) NVIDIA(0): No modes were requested; the default mode "nvidia-auto-select"
[ 9.245] (==) NVIDIA(0): will be used as the requested mode.
[ 9.245] (==) NVIDIA(0):
[ 9.245] (II) NVIDIA(0): Validated MetaModes:
[ 9.245] (II) NVIDIA(0): "DFP-1:nvidia-auto-select"
[ 9.245] (II) NVIDIA(0): Virtual screen size determined to be 2560 x 1600
[ 9.247] (--) NVIDIA(0): DPI set to (185, 184); computed from "UseEdidDpi" X config
[ 9.247] (--) NVIDIA(0): option
[ 9.247] (==) modeset(G0): Depth 24, (==) framebuffer bpp 32
[ 9.247] (==) modeset(G0): RGB weight 888
[ 9.247] (==) modeset(G0): Default visual is TrueColor
[ 9.247] (II) Loading sub module "glamoregl"
[ 9.247] (II) LoadModule: "glamoregl"
[ 9.247] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 9.249] (II) Module glamoregl: vendor="X.Org Foundation"
[ 9.249] compiled for 1.21.1.13, module version = 1.0.1
[ 9.249] ABI class: X.Org ANSI C Emulation, version 0.4
[ 9.270] (II) modeset(G0): glamor X acceleration enabled on AMD Radeon Graphics (radeonsi, raphael_mendocino, LLVM 17.0.6, DRM 3.57, 6.8.7-arch1-1)
[ 9.270] (II) modeset(G0): glamor initialized
[ 9.270] (II) modeset(G0): Output eDP-1-2 has no monitor section
[ 9.271] (II) modeset(G0): Output DP-1-1 has no monitor section
[ 9.271] (II) modeset(G0): Output DP-1-2 has no monitor section
[ 9.271] (II) modeset(G0): Output DP-1-3 has no monitor section
[ 9.271] (II) modeset(G0): EDID for output eDP-1-2
[ 9.271] (II) modeset(G0): EDID for output DP-1-1
[ 9.271] (II) modeset(G0): EDID for output DP-1-2
[ 9.271] (II) modeset(G0): EDID for output DP-1-3
[ 9.271] (==) modeset(G0): Using gamma correction (1.0, 1.0, 1.0)
[ 9.271] (==) modeset(G0): DPI set to (96, 96)
[ 9.271] (II) Loading sub module "fb"
[ 9.271] (II) LoadModule: "fb"
[ 9.271] (II) Module "fb" already built-in
[ 9.271] (==) modeset(G1): Depth 24, (==) framebuffer bpp 32
[ 9.271] (==) modeset(G1): RGB weight 888
[ 9.271] (==) modeset(G1): Default visual is TrueColor
[ 9.271] (II) Loading sub module "glamoregl"
[ 9.271] (II) LoadModule: "glamoregl"
[ 9.271] (II) Loading /usr/lib/xorg/modules/libglamoregl.so
[ 9.271] (II) Module glamoregl: vendor="X.Org Foundation"
[ 9.271] compiled for 1.21.1.13, module version = 1.0.1
[ 9.271] ABI class: X.Org ANSI C Emulation, version 0.4
[ 9.279] (II) modeset(G1): Refusing to try glamor on llvmpipe
[ 9.279] (II) modeset(G1): glamor initialization failed
[ 9.279] (II) modeset(G1): ShadowFB: preferred NO, enabled NO
[ 9.279] (II) modeset(G1): Output None-2-1 has no monitor section
[ 9.279] (II) modeset(G1): EDID for output None-2-1
[ 9.279] (II) modeset(G1): Printing probed modes for output None-2-1
[ 9.279] (II) modeset(G1): Modeline "2560x1600"x60.0 245.76 2560 2560 2560 2560 1600 1600 1600 1600 (96.0 kHz eP)
[ 9.279] (==) modeset(G1): Using gamma correction (1.0, 1.0, 1.0)
[ 9.279] (==) modeset(G1): DPI set to (96, 96)
[ 9.279] (II) Loading sub module "fb"
[ 9.279] (II) LoadModule: "fb"
[ 9.279] (II) Module "fb" already built-in
[ 9.280] (II) NVIDIA: Reserving 24576.00 MB of virtual memory for indirect memory
[ 9.280] (II) NVIDIA: access.
[ 9.281] (II) NVIDIA(0): ACPI: failed to connect to the ACPI event daemon; the daemon
[ 9.281] (II) NVIDIA(0): may not be running or the "AcpidSocketPath" X
[ 9.281] (II) NVIDIA(0): configuration option may not be set correctly. When the
[ 9.281] (II) NVIDIA(0): ACPI event daemon is available, the NVIDIA X driver will
[ 9.281] (II) NVIDIA(0): try to use it to receive ACPI event notifications. For
[ 9.281] (II) NVIDIA(0): details, please see the "ConnectToAcpid" and
[ 9.281] (II) NVIDIA(0): "AcpidSocketPath" X configuration options in Appendix B: X
[ 9.281] (II) NVIDIA(0): Config Options in the README.
[ 9.295] (II) NVIDIA(0): Setting mode "DFP-1:nvidia-auto-select"
[ 10.365] (==) NVIDIA(0): Disabling shared memory pixmaps
[ 10.365] (==) NVIDIA(0): Backing store enabled
[ 10.365] (==) NVIDIA(0): Silken mouse enabled
[ 10.365] (==) NVIDIA(0): DPMS enabled
[ 10.365] (II) Loading sub module "dri2"
[ 10.365] (II) LoadModule: "dri2"
[ 10.365] (II) Module "dri2" already built-in
[ 10.365] (II) NVIDIA(0): [DRI2] Setup complete
[ 10.365] (II) NVIDIA(0): [DRI2] VDPAU driver: nvidia
[ 10.375] (==) modeset(G0): Backing store enabled
[ 10.375] (==) modeset(G0): Silken mouse enabled
[ 10.375] (II) modeset(G0): Initializing kms color map for depth 24, 8 bpc.
[ 10.375] (==) modeset(G0): DPMS enabled
[ 10.375] (II) modeset(G0): [DRI2] Setup complete
[ 10.375] (II) modeset(G0): [DRI2] DRI driver: radeonsi
[ 10.375] (II) modeset(G0): [DRI2] VDPAU driver: radeonsi
[ 10.376] (==) modeset(G1): Backing store enabled
[ 10.376] (==) modeset(G1): Silken mouse enabled
[ 10.376] (II) modeset(G1): Initializing kms color map for depth 24, 8 bpc.
[ 10.376] (==) modeset(G1): DPMS enabled
[ 10.376] (II) Initializing extension Generic Event Extension
[ 10.376] (II) Initializing extension SHAPE
[ 10.376] (II) Initializing extension MIT-SHM
[ 10.376] (II) Initializing extension XInputExtension
[ 10.376] (II) Initializing extension XTEST
[ 10.376] (II) Initializing extension BIG-REQUESTS
[ 10.376] (II) Initializing extension SYNC
[ 10.376] (II) Initializing extension XKEYBOARD
[ 10.376] (II) Initializing extension XC-MISC
[ 10.376] (II) Initializing extension SECURITY
[ 10.376] (II) Initializing extension XFIXES
[ 10.376] (II) Initializing extension RENDER
[ 10.376] (II) Initializing extension RANDR
[ 10.376] (II) Initializing extension COMPOSITE
[ 10.376] (II) Initializing extension DAMAGE
[ 10.376] (II) Initializing extension MIT-SCREEN-SAVER
[ 10.376] (II) Initializing extension DOUBLE-BUFFER
[ 10.377] (II) Initializing extension RECORD
[ 10.377] (II) Initializing extension DPMS
[ 10.377] (II) Initializing extension Present
[ 10.377] (II) Initializing extension DRI3
[ 10.377] (II) Initializing extension X-Resource
[ 10.377] (II) Initializing extension XVideo
[ 10.377] (II) Initializing extension XVideo-MotionCompensation
[ 10.377] (II) Initializing extension GLX
[ 10.377] (II) Initializing extension GLX
[ 10.377] (II) Indirect GLX disabled.
[ 10.377] (II) GLX: Another vendor is already registered for screen 0
[ 10.377] (II) Initializing extension XFree86-VidModeExtension
[ 10.377] (II) Initializing extension XFree86-DGA
[ 10.377] (II) Initializing extension XFree86-DRI
[ 10.377] (II) Initializing extension DRI2
[ 10.377] (II) Initializing extension NV-GLX
[ 10.377] (II) Initializing extension NV-CONTROL
[ 10.377] (II) Initializing extension XINERAMA
[ 10.377] (II) modeset(G0): Damage tracking initialized
[ 10.380] (II) modeset(G1): Damage tracking initialized
[ 10.420] (II) config/udev: Adding input device Video Bus (/dev/input/event5)
[ 10.420] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[ 10.420] (**) Video Bus: Applying InputClass "system-keyboard"
[ 10.420] (II) LoadModule: "libinput"
[ 10.420] (II) Loading /usr/lib/xorg/modules/input/libinput_drv.so
[ 10.421] (II) Module libinput: vendor="X.Org Foundation"
[ 10.421] compiled for 1.21.1.8, module version = 1.4.0
[ 10.421] Module class: X.Org XInput Driver
[ 10.421] ABI class: X.Org XInput driver, version 24.4
[ 10.421] (II) Using input driver 'libinput' for 'Video Bus'
[ 10.421] (**) Video Bus: always reports core events
[ 10.421] (**) Option "Device" "/dev/input/event5"
[ 10.422] (II) event5 - Video Bus: is tagged by udev as: Keyboard
[ 10.422] (II) event5 - Video Bus: device is a keyboard
[ 10.422] (II) event5 - Video Bus: device removed
[ 10.470] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:00/LNXVIDEO:00/input/input5/event5"
[ 10.470] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 6)
[ 10.470] (**) Option "xkb_model" "pc105+inet"
[ 10.470] (**) Option "xkb_layout" "us"
[ 10.470] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.481] (II) event5 - Video Bus: is tagged by udev as: Keyboard
[ 10.481] (II) event5 - Video Bus: device is a keyboard
[ 10.481] (II) config/udev: Adding input device Video Bus (/dev/input/event6)
[ 10.481] (**) Video Bus: Applying InputClass "libinput keyboard catchall"
[ 10.481] (**) Video Bus: Applying InputClass "system-keyboard"
[ 10.481] (II) Using input driver 'libinput' for 'Video Bus'
[ 10.481] (**) Video Bus: always reports core events
[ 10.481] (**) Option "Device" "/dev/input/event6"
[ 10.482] (II) event6 - Video Bus: is tagged by udev as: Keyboard
[ 10.482] (II) event6 - Video Bus: device is a keyboard
[ 10.482] (II) event6 - Video Bus: device removed
[ 10.527] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/device:0f/LNXVIDEO:01/input/input6/event6"
[ 10.527] (II) XINPUT: Adding extended input device "Video Bus" (type: KEYBOARD, id 7)
[ 10.527] (**) Option "xkb_model" "pc105+inet"
[ 10.527] (**) Option "xkb_layout" "us"
[ 10.527] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.527] (II) event6 - Video Bus: is tagged by udev as: Keyboard
[ 10.528] (II) event6 - Video Bus: device is a keyboard
[ 10.528] (II) config/udev: Adding input device Lid Switch (/dev/input/event1)
[ 10.528] (II) No input driver specified, ignoring this device.
[ 10.528] (II) This device may have been added with another device file.
[ 10.528] (II) config/udev: Adding input device Power Button (/dev/input/event0)
[ 10.528] (**) Power Button: Applying InputClass "libinput keyboard catchall"
[ 10.528] (**) Power Button: Applying InputClass "system-keyboard"
[ 10.528] (II) Using input driver 'libinput' for 'Power Button'
[ 10.528] (**) Power Button: always reports core events
[ 10.528] (**) Option "Device" "/dev/input/event0"
[ 10.529] (II) event0 - Power Button: is tagged by udev as: Keyboard
[ 10.529] (II) event0 - Power Button: device is a keyboard
[ 10.529] (II) event0 - Power Button: device removed
[ 10.543] (**) Option "config_info" "udev:/sys/devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0/event0"
[ 10.543] (II) XINPUT: Adding extended input device "Power Button" (type: KEYBOARD, id 8)
[ 10.543] (**) Option "xkb_model" "pc105+inet"
[ 10.543] (**) Option "xkb_layout" "us"
[ 10.543] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.544] (II) event0 - Power Button: is tagged by udev as: Keyboard
[ 10.544] (II) event0 - Power Button: device is a keyboard
[ 10.544] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=3 (/dev/input/event13)
[ 10.544] (II) No input driver specified, ignoring this device.
[ 10.544] (II) This device may have been added with another device file.
[ 10.545] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=7 (/dev/input/event14)
[ 10.545] (II) No input driver specified, ignoring this device.
[ 10.545] (II) This device may have been added with another device file.
[ 10.545] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=8 (/dev/input/event19)
[ 10.545] (II) No input driver specified, ignoring this device.
[ 10.545] (II) This device may have been added with another device file.
[ 10.545] (II) config/udev: Adding input device HDA NVidia HDMI/DP,pcm=9 (/dev/input/event21)
[ 10.545] (II) No input driver specified, ignoring this device.
[ 10.545] (II) This device may have been added with another device file.
[ 10.545] (II) config/udev: Adding input device HD-Audio Generic HDMI/DP,pcm=3 (/dev/input/event12)
[ 10.545] (II) No input driver specified, ignoring this device.
[ 10.545] (II) This device may have been added with another device file.
[ 10.546] (II) config/udev: Adding input device Logitech G304 (/dev/input/event10)
[ 10.546] (**) Logitech G304: Applying InputClass "libinput pointer catchall"
[ 10.546] (**) Logitech G304: Applying InputClass "libinput keyboard catchall"
[ 10.546] (**) Logitech G304: Applying InputClass "system-keyboard"
[ 10.546] (II) Using input driver 'libinput' for 'Logitech G304'
[ 10.546] (**) Logitech G304: always reports core events
[ 10.546] (**) Option "Device" "/dev/input/event10"
[ 10.547] (II) event10 - Logitech G304: is tagged by udev as: Keyboard Mouse
[ 10.547] (II) event10 - Logitech G304: device is a pointer
[ 10.547] (II) event10 - Logitech G304: device is a keyboard
[ 10.547] (II) event10 - Logitech G304: device removed
[ 10.580] (II) libinput: Logitech G304: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.580] (II) libinput: Logitech G304: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.580] (II) libinput: Logitech G304: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.580] (II) libinput: Logitech G304: needs a virtual subdevice
[ 10.580] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.1/0000:06:00.4/usb3/3-1/3-1:1.2/0003:046D:C53F.0003/0003:046D:4074.0008/input/input36/event10"
[ 10.580] (II) XINPUT: Adding extended input device "Logitech G304" (type: MOUSE, id 9)
[ 10.580] (**) Option "AccelerationScheme" "none"
[ 10.580] (**) Logitech G304: (accel) selected scheme none/0
[ 10.580] (**) Logitech G304: (accel) acceleration factor: 2.000
[ 10.580] (**) Logitech G304: (accel) acceleration threshold: 4
[ 10.581] (II) event10 - Logitech G304: is tagged by udev as: Keyboard Mouse
[ 10.581] (II) event10 - Logitech G304: device is a pointer
[ 10.581] (II) event10 - Logitech G304: device is a keyboard
[ 10.582] (II) config/udev: Adding input device Logitech G304 (/dev/input/mouse3)
[ 10.582] (**) Logitech G304: Applying InputClass "system-keyboard"
[ 10.582] (II) No input driver specified, ignoring this device.
[ 10.582] (II) This device may have been added with another device file.
[ 10.582] (II) config/udev: Adding input device HD-Audio Generic Mic (/dev/input/event15)
[ 10.582] (II) No input driver specified, ignoring this device.
[ 10.582] (II) This device may have been added with another device file.
[ 10.582] (II) config/udev: Adding input device HD-Audio Generic Headphone (/dev/input/event17)
[ 10.582] (II) No input driver specified, ignoring this device.
[ 10.582] (II) This device may have been added with another device file.
[ 10.583] (II) config/udev: Adding input device ITE Tech. Inc. ITE Device(8910) Keyboard (/dev/input/event23)
[ 10.583] (**) ITE Tech. Inc. ITE Device(8910) Keyboard: Applying InputClass "libinput keyboard catchall"
[ 10.583] (**) ITE Tech. Inc. ITE Device(8910) Keyboard: Applying InputClass "system-keyboard"
[ 10.583] (II) Using input driver 'libinput' for 'ITE Tech. Inc. ITE Device(8910) Keyboard'
[ 10.583] (**) ITE Tech. Inc. ITE Device(8910) Keyboard: always reports core events
[ 10.583] (**) Option "Device" "/dev/input/event23"
[ 10.583] (II) event23 - ITE Tech. Inc. ITE Device(8910) Keyboard: is tagged by udev as: Keyboard
[ 10.583] (II) event23 - ITE Tech. Inc. ITE Device(8910) Keyboard: device is a keyboard
[ 10.584] (II) event23 - ITE Tech. Inc. ITE Device(8910) Keyboard: device removed
[ 10.607] (II) libinput: ITE Tech. Inc. ITE Device(8910) Keyboard: needs a virtual subdevice
[ 10.607] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.3/0000:07:00.0/usb5/5-1/5-1.3/5-1.3:1.0/0003:048D:8910.0004/input/input25/event23"
[ 10.607] (II) XINPUT: Adding extended input device "ITE Tech. Inc. ITE Device(8910) Keyboard" (type: MOUSE, id 10)
[ 10.607] (**) Option "AccelerationScheme" "none"
[ 10.607] (**) ITE Tech. Inc. ITE Device(8910) Keyboard: (accel) selected scheme none/0
[ 10.607] (**) ITE Tech. Inc. ITE Device(8910) Keyboard: (accel) acceleration factor: 2.000
[ 10.607] (**) ITE Tech. Inc. ITE Device(8910) Keyboard: (accel) acceleration threshold: 4
[ 10.608] (II) event23 - ITE Tech. Inc. ITE Device(8910) Keyboard: is tagged by udev as: Keyboard
[ 10.608] (II) event23 - ITE Tech. Inc. ITE Device(8910) Keyboard: device is a keyboard
[ 10.608] (II) config/udev: Adding input device ITE Tech. Inc. ITE Device(8910) Wireless Radio Control (/dev/input/event24)
[ 10.608] (**) ITE Tech. Inc. ITE Device(8910) Wireless Radio Control: Applying InputClass "libinput keyboard catchall"
[ 10.608] (**) ITE Tech. Inc. ITE Device(8910) Wireless Radio Control: Applying InputClass "system-keyboard"
[ 10.608] (II) Using input driver 'libinput' for 'ITE Tech. Inc. ITE Device(8910) Wireless Radio Control'
[ 10.608] (**) ITE Tech. Inc. ITE Device(8910) Wireless Radio Control: always reports core events
[ 10.608] (**) Option "Device" "/dev/input/event24"
[ 10.609] (II) event24 - ITE Tech. Inc. ITE Device(8910) Wireless Radio Control: is tagged by udev as: Keyboard
[ 10.609] (II) event24 - ITE Tech. Inc. ITE Device(8910) Wireless Radio Control: device is a keyboard
[ 10.609] (II) event24 - ITE Tech. Inc. ITE Device(8910) Wireless Radio Control: device removed
[ 10.640] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.3/0000:07:00.0/usb5/5-1/5-1.3/5-1.3:1.0/0003:048D:8910.0004/input/input26/event24"
[ 10.640] (II) XINPUT: Adding extended input device "ITE Tech. Inc. ITE Device(8910) Wireless Radio Control" (type: KEYBOARD, id 11)
[ 10.640] (**) Option "xkb_model" "pc105+inet"
[ 10.640] (**) Option "xkb_layout" "us"
[ 10.640] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.641] (II) event24 - ITE Tech. Inc. ITE Device(8910) Wireless Radio Control: is tagged by udev as: Keyboard
[ 10.641] (II) event24 - ITE Tech. Inc. ITE Device(8910) Wireless Radio Control: device is a keyboard
[ 10.642] (II) config/udev: Adding input device BY Tech Gaming Keyboard (/dev/input/event8)
[ 10.642] (**) BY Tech Gaming Keyboard: Applying InputClass "libinput keyboard catchall"
[ 10.642] (**) BY Tech Gaming Keyboard: Applying InputClass "system-keyboard"
[ 10.642] (II) Using input driver 'libinput' for 'BY Tech Gaming Keyboard'
[ 10.642] (**) BY Tech Gaming Keyboard: always reports core events
[ 10.642] (**) Option "Device" "/dev/input/event8"
[ 10.642] (II) event8 - BY Tech Gaming Keyboard: is tagged by udev as: Keyboard
[ 10.642] (II) event8 - BY Tech Gaming Keyboard: device is a keyboard
[ 10.643] (II) event8 - BY Tech Gaming Keyboard: device removed
[ 10.667] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.3/0000:07:00.0/usb5/5-1/5-1.4/5-1.4:1.0/0003:258A:014C.0006/input/input8/event8"
[ 10.667] (II) XINPUT: Adding extended input device "BY Tech Gaming Keyboard" (type: KEYBOARD, id 12)
[ 10.667] (**) Option "xkb_model" "pc105+inet"
[ 10.667] (**) Option "xkb_layout" "us"
[ 10.667] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.668] (II) event8 - BY Tech Gaming Keyboard: is tagged by udev as: Keyboard
[ 10.668] (II) event8 - BY Tech Gaming Keyboard: device is a keyboard
[ 10.668] (II) config/udev: Adding input device BY Tech Gaming Keyboard System Control (/dev/input/event11)
[ 10.669] (**) BY Tech Gaming Keyboard System Control: Applying InputClass "libinput keyboard catchall"
[ 10.669] (**) BY Tech Gaming Keyboard System Control: Applying InputClass "system-keyboard"
[ 10.669] (II) Using input driver 'libinput' for 'BY Tech Gaming Keyboard System Control'
[ 10.669] (**) BY Tech Gaming Keyboard System Control: always reports core events
[ 10.669] (**) Option "Device" "/dev/input/event11"
[ 10.669] (II) event11 - BY Tech Gaming Keyboard System Control: is tagged by udev as: Keyboard
[ 10.669] (II) event11 - BY Tech Gaming Keyboard System Control: device is a keyboard
[ 10.669] (II) event11 - BY Tech Gaming Keyboard System Control: device removed
[ 10.683] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.3/0000:07:00.0/usb5/5-1/5-1.4/5-1.4:1.1/0003:258A:014C.0007/input/input13/event11"
[ 10.683] (II) XINPUT: Adding extended input device "BY Tech Gaming Keyboard System Control" (type: KEYBOARD, id 13)
[ 10.683] (**) Option "xkb_model" "pc105+inet"
[ 10.683] (**) Option "xkb_layout" "us"
[ 10.683] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.684] (II) event11 - BY Tech Gaming Keyboard System Control: is tagged by udev as: Keyboard
[ 10.684] (II) event11 - BY Tech Gaming Keyboard System Control: device is a keyboard
[ 10.685] (II) config/udev: Adding input device BY Tech Gaming Keyboard Consumer Control (/dev/input/event18)
[ 10.685] (**) BY Tech Gaming Keyboard Consumer Control: Applying InputClass "libinput keyboard catchall"
[ 10.685] (**) BY Tech Gaming Keyboard Consumer Control: Applying InputClass "system-keyboard"
[ 10.685] (II) Using input driver 'libinput' for 'BY Tech Gaming Keyboard Consumer Control'
[ 10.685] (**) BY Tech Gaming Keyboard Consumer Control: always reports core events
[ 10.685] (**) Option "Device" "/dev/input/event18"
[ 10.686] (II) event18 - BY Tech Gaming Keyboard Consumer Control: is tagged by udev as: Keyboard
[ 10.686] (II) event18 - BY Tech Gaming Keyboard Consumer Control: device is a keyboard
[ 10.686] (II) event18 - BY Tech Gaming Keyboard Consumer Control: device removed
[ 10.700] (II) libinput: BY Tech Gaming Keyboard Consumer Control: needs a virtual subdevice
[ 10.700] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.3/0000:07:00.0/usb5/5-1/5-1.4/5-1.4:1.1/0003:258A:014C.0007/input/input14/event18"
[ 10.700] (II) XINPUT: Adding extended input device "BY Tech Gaming Keyboard Consumer Control" (type: MOUSE, id 14)
[ 10.700] (**) Option "AccelerationScheme" "none"
[ 10.700] (**) BY Tech Gaming Keyboard Consumer Control: (accel) selected scheme none/0
[ 10.700] (**) BY Tech Gaming Keyboard Consumer Control: (accel) acceleration factor: 2.000
[ 10.700] (**) BY Tech Gaming Keyboard Consumer Control: (accel) acceleration threshold: 4
[ 10.701] (II) event18 - BY Tech Gaming Keyboard Consumer Control: is tagged by udev as: Keyboard
[ 10.701] (II) event18 - BY Tech Gaming Keyboard Consumer Control: device is a keyboard
[ 10.702] (II) config/udev: Adding input device BY Tech Gaming Keyboard (/dev/input/event20)
[ 10.702] (**) BY Tech Gaming Keyboard: Applying InputClass "libinput keyboard catchall"
[ 10.702] (**) BY Tech Gaming Keyboard: Applying InputClass "system-keyboard"
[ 10.702] (II) Using input driver 'libinput' for 'BY Tech Gaming Keyboard'
[ 10.702] (**) BY Tech Gaming Keyboard: always reports core events
[ 10.702] (**) Option "Device" "/dev/input/event20"
[ 10.702] (II) event20 - BY Tech Gaming Keyboard: is tagged by udev as: Keyboard
[ 10.702] (II) event20 - BY Tech Gaming Keyboard: device is a keyboard
[ 10.703] (II) event20 - BY Tech Gaming Keyboard: device removed
[ 10.727] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.3/0000:07:00.0/usb5/5-1/5-1.4/5-1.4:1.1/0003:258A:014C.0007/input/input16/event20"
[ 10.727] (II) XINPUT: Adding extended input device "BY Tech Gaming Keyboard" (type: KEYBOARD, id 15)
[ 10.727] (**) Option "xkb_model" "pc105+inet"
[ 10.727] (**) Option "xkb_layout" "us"
[ 10.727] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.728] (II) event20 - BY Tech Gaming Keyboard: is tagged by udev as: Keyboard
[ 10.728] (II) event20 - BY Tech Gaming Keyboard: device is a keyboard
[ 10.728] (II) config/udev: Adding input device BY Tech Gaming Keyboard Mouse (/dev/input/event22)
[ 10.728] (**) BY Tech Gaming Keyboard Mouse: Applying InputClass "libinput pointer catchall"
[ 10.728] (II) Using input driver 'libinput' for 'BY Tech Gaming Keyboard Mouse'
[ 10.728] (**) BY Tech Gaming Keyboard Mouse: always reports core events
[ 10.728] (**) Option "Device" "/dev/input/event22"
[ 10.729] (II) event22 - BY Tech Gaming Keyboard Mouse: is tagged by udev as: Mouse
[ 10.729] (II) event22 - BY Tech Gaming Keyboard Mouse: device is a pointer
[ 10.729] (II) event22 - BY Tech Gaming Keyboard Mouse: device removed
[ 10.760] (II) libinput: BY Tech Gaming Keyboard Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.760] (II) libinput: BY Tech Gaming Keyboard Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.760] (II) libinput: BY Tech Gaming Keyboard Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.760] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.3/0000:07:00.0/usb5/5-1/5-1.4/5-1.4:1.1/0003:258A:014C.0007/input/input17/event22"
[ 10.760] (II) XINPUT: Adding extended input device "BY Tech Gaming Keyboard Mouse" (type: MOUSE, id 16)
[ 10.760] (**) Option "AccelerationScheme" "none"
[ 10.760] (**) BY Tech Gaming Keyboard Mouse: (accel) selected scheme none/0
[ 10.760] (**) BY Tech Gaming Keyboard Mouse: (accel) acceleration factor: 2.000
[ 10.760] (**) BY Tech Gaming Keyboard Mouse: (accel) acceleration threshold: 4
[ 10.761] (II) event22 - BY Tech Gaming Keyboard Mouse: is tagged by udev as: Mouse
[ 10.761] (II) event22 - BY Tech Gaming Keyboard Mouse: device is a pointer
[ 10.762] (II) config/udev: Adding input device BY Tech Gaming Keyboard Mouse (/dev/input/mouse0)
[ 10.762] (II) No input driver specified, ignoring this device.
[ 10.762] (II) This device may have been added with another device file.
[ 10.762] (II) config/udev: Adding input device HTIX5288:00 0911:5288 Mouse (/dev/input/event7)
[ 10.762] (**) HTIX5288:00 0911:5288 Mouse: Applying InputClass "libinput pointer catchall"
[ 10.762] (II) Using input driver 'libinput' for 'HTIX5288:00 0911:5288 Mouse'
[ 10.762] (**) HTIX5288:00 0911:5288 Mouse: always reports core events
[ 10.762] (**) Option "Device" "/dev/input/event7"
[ 10.763] (II) event7 - HTIX5288:00 0911:5288 Mouse: is tagged by udev as: Mouse Pointingstick
[ 10.763] (II) event7 - HTIX5288:00 0911:5288 Mouse: device is a pointer
[ 10.763] (II) event7 - HTIX5288:00 0911:5288 Mouse: device removed
[ 10.813] (II) libinput: HTIX5288:00 0911:5288 Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.813] (II) libinput: HTIX5288:00 0911:5288 Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.813] (II) libinput: HTIX5288:00 0911:5288 Mouse: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.813] (**) Option "config_info" "udev:/sys/devices/platform/AMDI0010:03/i2c-2/i2c-HTIX5288:00/0018:0911:5288.0005/input/input34/event7"
[ 10.813] (II) XINPUT: Adding extended input device "HTIX5288:00 0911:5288 Mouse" (type: MOUSE, id 17)
[ 10.813] (**) Option "AccelerationScheme" "none"
[ 10.813] (**) HTIX5288:00 0911:5288 Mouse: (accel) selected scheme none/0
[ 10.813] (**) HTIX5288:00 0911:5288 Mouse: (accel) acceleration factor: 2.000
[ 10.813] (**) HTIX5288:00 0911:5288 Mouse: (accel) acceleration threshold: 4
[ 10.814] (II) event7 - HTIX5288:00 0911:5288 Mouse: is tagged by udev as: Mouse Pointingstick
[ 10.814] (II) event7 - HTIX5288:00 0911:5288 Mouse: device is a pointer
[ 10.815] (II) config/udev: Adding input device HTIX5288:00 0911:5288 Mouse (/dev/input/mouse2)
[ 10.815] (II) No input driver specified, ignoring this device.
[ 10.815] (II) This device may have been added with another device file.
[ 10.816] (II) config/udev: Adding input device HTIX5288:00 0911:5288 Touchpad (/dev/input/event9)
[ 10.816] (**) HTIX5288:00 0911:5288 Touchpad: Applying InputClass "libinput touchpad catchall"
[ 10.816] (II) Using input driver 'libinput' for 'HTIX5288:00 0911:5288 Touchpad'
[ 10.816] (**) HTIX5288:00 0911:5288 Touchpad: always reports core events
[ 10.816] (**) Option "Device" "/dev/input/event9"
[ 10.816] (II) event9 - HTIX5288:00 0911:5288 Touchpad: is tagged by udev as: Touchpad
[ 10.817] (II) event9 - HTIX5288:00 0911:5288 Touchpad: device is a touchpad
[ 10.817] (II) event9 - HTIX5288:00 0911:5288 Touchpad: device removed
[ 10.857] (II) libinput: HTIX5288:00 0911:5288 Touchpad: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.857] (II) libinput: HTIX5288:00 0911:5288 Touchpad: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.857] (II) libinput: HTIX5288:00 0911:5288 Touchpad: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.857] (**) Option "config_info" "udev:/sys/devices/platform/AMDI0010:03/i2c-2/i2c-HTIX5288:00/0018:0911:5288.0005/input/input35/event9"
[ 10.857] (II) XINPUT: Adding extended input device "HTIX5288:00 0911:5288 Touchpad" (type: TOUCHPAD, id 18)
[ 10.858] (**) Option "AccelerationScheme" "none"
[ 10.858] (**) HTIX5288:00 0911:5288 Touchpad: (accel) selected scheme none/0
[ 10.858] (**) HTIX5288:00 0911:5288 Touchpad: (accel) acceleration factor: 2.000
[ 10.858] (**) HTIX5288:00 0911:5288 Touchpad: (accel) acceleration threshold: 4
[ 10.859] (II) event9 - HTIX5288:00 0911:5288 Touchpad: is tagged by udev as: Touchpad
[ 10.860] (II) event9 - HTIX5288:00 0911:5288 Touchpad: device is a touchpad
[ 10.860] (II) config/udev: Adding input device HTIX5288:00 0911:5288 Touchpad (/dev/input/mouse1)
[ 10.860] (II) No input driver specified, ignoring this device.
[ 10.860] (II) This device may have been added with another device file.
[ 10.860] (II) config/udev: Adding input device AT Translated Set 2 keyboard (/dev/input/event2)
[ 10.860] (**) AT Translated Set 2 keyboard: Applying InputClass "libinput keyboard catchall"
[ 10.860] (**) AT Translated Set 2 keyboard: Applying InputClass "system-keyboard"
[ 10.860] (II) Using input driver 'libinput' for 'AT Translated Set 2 keyboard'
[ 10.860] (**) AT Translated Set 2 keyboard: always reports core events
[ 10.860] (**) Option "Device" "/dev/input/event2"
[ 10.861] (II) event2 - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[ 10.861] (II) event2 - AT Translated Set 2 keyboard: device is a keyboard
[ 10.862] (II) event2 - AT Translated Set 2 keyboard: device removed
[ 10.883] (**) Option "config_info" "udev:/sys/devices/platform/i8042/serio0/input/input2/event2"
[ 10.883] (II) XINPUT: Adding extended input device "AT Translated Set 2 keyboard" (type: KEYBOARD, id 19)
[ 10.883] (**) Option "xkb_model" "pc105+inet"
[ 10.883] (**) Option "xkb_layout" "us"
[ 10.883] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.884] (II) event2 - AT Translated Set 2 keyboard: is tagged by udev as: Keyboard
[ 10.884] (II) event2 - AT Translated Set 2 keyboard: device is a keyboard
[ 10.885] (II) config/udev: Adding input device PC Speaker (/dev/input/event4)
[ 10.885] (II) No input driver specified, ignoring this device.
[ 10.885] (II) This device may have been added with another device file.
[ 10.887] (II) config/udev: Adding input device Wireless hotkeys (/dev/input/event3)
[ 10.887] (**) Wireless hotkeys: Applying InputClass "libinput keyboard catchall"
[ 10.887] (**) Wireless hotkeys: Applying InputClass "system-keyboard"
[ 10.887] (II) Using input driver 'libinput' for 'Wireless hotkeys'
[ 10.887] (**) Wireless hotkeys: always reports core events
[ 10.887] (**) Option "Device" "/dev/input/event3"
[ 10.887] (II) event3 - Wireless hotkeys: is tagged by udev as: Keyboard
[ 10.887] (II) event3 - Wireless hotkeys: device is a keyboard
[ 10.887] (II) event3 - Wireless hotkeys: device removed
[ 10.937] (**) Option "config_info" "udev:/sys/devices/virtual/input/input4/event3"
[ 10.937] (II) XINPUT: Adding extended input device "Wireless hotkeys" (type: KEYBOARD, id 20)
[ 10.937] (**) Option "xkb_model" "pc105+inet"
[ 10.937] (**) Option "xkb_layout" "us"
[ 10.937] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.937] (II) event3 - Wireless hotkeys: is tagged by udev as: Keyboard
[ 10.937] (II) event3 - Wireless hotkeys: device is a keyboard
[ 10.940] (**) Logitech G304: Applying InputClass "libinput pointer catchall"
[ 10.940] (**) Logitech G304: Applying InputClass "libinput keyboard catchall"
[ 10.940] (**) Logitech G304: Applying InputClass "system-keyboard"
[ 10.940] (II) Using input driver 'libinput' for 'Logitech G304'
[ 10.940] (**) Logitech G304: always reports core events
[ 10.940] (**) Option "Device" "/dev/input/event10"
[ 10.940] (II) libinput: Logitech G304: is a virtual subdevice
[ 10.940] (II) libinput: Logitech G304: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.940] (II) libinput: Logitech G304: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.940] (II) libinput: Logitech G304: Step value 0 was provided, libinput Fallback acceleration function is used.
[ 10.940] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.1/0000:06:00.4/usb3/3-1/3-1:1.2/0003:046D:C53F.0003/0003:046D:4074.0008/input/input36/event10"
[ 10.940] (II) XINPUT: Adding extended input device "Logitech G304" (type: KEYBOARD, id 21)
[ 10.940] (**) Option "xkb_model" "pc105+inet"
[ 10.940] (**) Option "xkb_layout" "us"
[ 10.940] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.940] (**) ITE Tech. Inc. ITE Device(8910) Keyboard: Applying InputClass "libinput keyboard catchall"
[ 10.940] (**) ITE Tech. Inc. ITE Device(8910) Keyboard: Applying InputClass "system-keyboard"
[ 10.940] (II) Using input driver 'libinput' for 'ITE Tech. Inc. ITE Device(8910) Keyboard'
[ 10.940] (**) ITE Tech. Inc. ITE Device(8910) Keyboard: always reports core events
[ 10.940] (**) Option "Device" "/dev/input/event23"
[ 10.940] (II) libinput: ITE Tech. Inc. ITE Device(8910) Keyboard: is a virtual subdevice
[ 10.940] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.3/0000:07:00.0/usb5/5-1/5-1.3/5-1.3:1.0/0003:048D:8910.0004/input/input25/event23"
[ 10.940] (II) XINPUT: Adding extended input device "ITE Tech. Inc. ITE Device(8910) Keyboard" (type: KEYBOARD, id 22)
[ 10.940] (**) Option "xkb_model" "pc105+inet"
[ 10.940] (**) Option "xkb_layout" "us"
[ 10.940] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 10.940] (**) BY Tech Gaming Keyboard Consumer Control: Applying InputClass "libinput keyboard catchall"
[ 10.940] (**) BY Tech Gaming Keyboard Consumer Control: Applying InputClass "system-keyboard"
[ 10.940] (II) Using input driver 'libinput' for 'BY Tech Gaming Keyboard Consumer Control'
[ 10.940] (**) BY Tech Gaming Keyboard Consumer Control: always reports core events
[ 10.940] (**) Option "Device" "/dev/input/event18"
[ 10.940] (II) libinput: BY Tech Gaming Keyboard Consumer Control: is a virtual subdevice
[ 10.940] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:08.3/0000:07:00.0/usb5/5-1/5-1.4/5-1.4:1.1/0003:258A:014C.0007/input/input14/event18"
[ 10.940] (II) XINPUT: Adding extended input device "BY Tech Gaming Keyboard Consumer Control" (type: KEYBOARD, id 23)
[ 10.940] (**) Option "xkb_model" "pc105+inet"
[ 10.940] (**) Option "xkb_layout" "us"
[ 10.940] (**) Option "xkb_options" "terminate:ctrl_alt_bksp"
[ 13.765] (II) event5 - Video Bus: device removed
[ 13.843] (II) event6 - Video Bus: device removed
[ 13.890] (II) event0 - Power Button: device removed
[ 13.906] (II) event24 - ITE Tech. Inc. ITE Device(8910) Wireless Radio Control: device removed
[ 13.940] (II) event8 - BY Tech Gaming Keyboard: device removed
[ 13.967] (II) event11 - BY Tech Gaming Keyboard System Control: device removed
[ 13.993] (II) event20 - BY Tech Gaming Keyboard: device removed
[ 14.020] (II) event22 - BY Tech Gaming Keyboard Mouse: device removed
[ 14.063] (II) event7 - HTIX5288:00 0911:5288 Mouse: device removed
[ 14.096] (II) event9 - HTIX5288:00 0911:5288 Touchpad: device removed
[ 14.140] (II) event2 - AT Translated Set 2 keyboard: device removed
[ 14.157] (II) event3 - Wireless hotkeys: device removed
[ 14.200] (II) event10 - Logitech G304: device removed
[ 14.227] (II) event23 - ITE Tech. Inc. ITE Device(8910) Keyboard: device removed
[ 14.253] (II) event18 - BY Tech Gaming Keyboard Consumer Control: device removedHere's my Xorg log.
Offline
#36 2024-04-25 09:36:21
- seth
- Member
- Registered: 2012-09-03
- Posts: 51,684
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
The raphale chip is there and suggests some eDP output, but the panel is connect to the nvidia chip and the 2670.0 MHz maximum pixel clock is more than sufficient for 2560x1440@240
My best guess is to test the various UEFI configs (notably nvidia only, amd only) to see whether this causes any changes and for the current config test the impact of forementioned https://wiki.archlinux.org/title/Variab … _on_NVIDIA (specifcally trying to disable that)
Offline
#37 2024-04-25 09:42:49
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
seth wrote:
try to disable the IGP/AMD GPU in the BIOS/UEFI.
These are the only two options in my bios
http://0x0.st/XHTu.jpg，I've been using discrete Mode.But now that I've tried hybrid mode, I've found that my refresh rate works fine, but I'm well aware that it's the amd gpu that's outputting the rendered results。If there is no good solution, I think I can continue to use the hybrid mode option, I really appreciate everyone taking time out of their busy schedules to solve my problem, especially seth!
Offline
#38 2024-04-25 10:18:04
- seth
- Member
- Registered: 2012-09-03
- Posts: 51,684
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
The eDP is probably directly wired to the AMD GPU and the load of the internal redirect is too much, maybe because the otherwise unused AMD GPU is powering down.
It's weird enough that it shows up in the "discrete" mode at all.
It's probably better to run the hybrid mode in a regular PRIME setup, but otherwise this can probably only be fixed with a firmware (BIOS/UEFI) udpate.
Offline
#39 2024-04-25 15:05:06
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
Yes, I've been using my computer with hybrid mode + envycontrol for a few hours now and I'm sure there's nothing out of the ordinary, thanks again for your help!
Offline
#40 Yesterday 16:11:06
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
Excuse me everyone, in today arch pushed me the nvidia 550.78 I upgraded him and I now have a system where everything works fine, and as I suspected it was a problem with Nvidia. But thanks to all of you for your previous answers. The purpose of my reply now is simply to let you know that the problem has been solved. How do I mark this issue as resolved?
Offline
#41 Yesterday 21:34:27
- seth
- Member
- Registered: 2012-09-03
- Posts: 51,684
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
\o/
Please always remember to mark resolved threads by editing your initial posts subject - so others will know that there's no task left, but maybe a solution to find.
Thanks.
Offline
#42 Today 05:22:52
- leessmin
- Member
- Registered: 2024-04-23
- Posts: 34
Re: [SOLVED]My laptop won't turn on the 240hz screen refresh rate
ok,I have now marked the problem [SOLVED],I read NVIDIA's release notes on the 550.78 driver and I think it's the above problem that's causing it!，nvidia550.78 Release Notes
Offline