You are not logged in.
- Topics: Active | Unanswered
#1 2024-05-20 02:07:40
- anarcobafif
- Member
- Registered: 2022-12-15
- Posts: 9
Monitor detected and enabled but no signal after boot
I've got two monitors:
$ xrandr --listmonitors
Monitors: 2
0: +*DP-1 1440/408x900/255+0+0 DP-1
1: +HDMI-1-0 1920/521x1080/293+0+0 HDMI-1-0HDMI-1-0 refers to the affected monitor and it's connected to NVidia GPU using nvidia propietary driver.
DP-1 refers to a secondary monitor wich is connected to Intel IGD.
$ lspci -n -n -k | grep -A 2 -e VGA -e 3D
00:02.0 VGA compatible controller [0300]: Intel Corporation CoffeeLake-S GT2 [UHD Graphics 630] [8086:3e91]
DeviceName: Onboard - Video
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:7b49]
--
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GP107 [GeForce GTX 1050 Ti] [10de:1c82] (rev a1)
Subsystem: Micro-Star International Co., Ltd. [MSI] Device [1462:3351]
Kernel driver in use: nvidia$ xrandr --listproviders
Providers: number : 2
Provider 0: id: 0x45 cap: 0xf, Source Output, Sink Output, Source Offload, Sink Offload crtcs: 3 outputs: 4 associated providers: 1 name:modesetting
Provider 1: id: 0x1fd cap: 0x2, Sink Output crtcs: 4 outputs: 4 associated providers: 1 name:NVIDIA-G0If I'm only using my graphics card, I can see firmware setup display on the HDMI monitor, I can use my mouse and keyboard, etc. I can enter EFI Shell, I can enter any boot manager as GRUB, REFInd, etc. When I boot the actual OS, the display just go off and my monitor says it can't find any signal from the HDMI cable.
I don't think it is a driver or configuration issue because I can't enter ArchISO live environment either. I can't enter TTY, the display turns off before login shell shows up.
The GPU turns on the RGB lights when I plug the power cable but the fan never starts spinning.
$ nvidia-smi
+-----------------------------------------------------------------------------------------+
| NVIDIA-SMI 550.78 Driver Version: 550.78 CUDA Version: 12.4 |
|-----------------------------------------+------------------------+----------------------+
| GPU Name Persistence-M | Bus-Id Disp.A | Volatile Uncorr. ECC |
| Fan Temp Perf Pwr:Usage/Cap | Memory-Usage | GPU-Util Compute M. |
| | | MIG M. |
|=========================================+========================+======================|
| 0 NVIDIA GeForce GTX 1050 Ti Off | 00000000:01:00.0 On | N/A |
| 0% 54C P0 N/A / 90W | 56MiB / 4096MiB | 0% Default |
| | | N/A |
+-----------------------------------------+------------------------+----------------------+
+-----------------------------------------------------------------------------------------+
| Processes: |
| GPU GI CI PID Type Process name GPU Memory |
| ID ID Usage |
|=========================================================================================|
| 0 N/A N/A 568 G /usr/lib/Xorg 45MiB |
+-----------------------------------------------------------------------------------------+$ sudo lshw -c video
*-display
descripción: VGA compatible controller
producto: GP107 [GeForce GTX 1050 Ti]
vendedor: NVIDIA Corporation
id físico: 0
información de bus: pci@0000:01:00.0
nombre lógico: /dev/fb1
versión: a1
anchura: 64 bits
reloj: 33MHz
capabilidades: pm msi pciexpress vga_controller bus_master cap_list rom fb
configuración: depth=32 driver=nvidia latency=0 resolution=1920,1080
recursos: irq:141 memoria:de000000-deffffff memoria:c0000000-cfffffff memoria:d0000000-d1ffffff ioport:e000(tamaño=128) memoria:df000000-df07ffff
*-display
descripción: VGA compatible controller
producto: CoffeeLake-S GT2 [UHD Graphics 630]
vendedor: Intel Corporation
id físico: 2
información de bus: pci@0000:00:02.0
nombre lógico: /dev/fb0
versión: 00
anchura: 64 bits
reloj: 33MHz
capabilidades: pciexpress msi pm vga_controller bus_master cap_list rom fb
configuración: depth=32 driver=i915 latency=0 resolution=1440,900
recursos: irq:137 memoria:dd000000-ddffffff memoria:b0000000-bfffffff ioport:f000(tamaño=64) memoria:c0000-dffffIt happened today so I didn't tried the GPU on other machine nor other GPU in my machine.
GPU: NVidia GeForce GTX 1050 Ti
CPU: Intel i3-8100
Last edited by anarcobafif (2024-05-20 02:34:11)
Offline
#2 2024-05-20 07:49:41
- seth
- Member
- From: Won't reply 2 private help req
- Registered: 2012-09-03
- Posts: 75,287
Re: Monitor detected and enabled but no signal after boot
xrandr -qOffline
#3 2024-05-20 16:39:29
- anarcobafif
- Member
- Registered: 2022-12-15
- Posts: 9
Re: Monitor detected and enabled but no signal after boot
xrandr -q
Screen 0: minimum 320 x 200, current 1920 x 1080, maximum 16384 x 16384
HDMI-1 disconnected (normal left inverted right x axis y axis)
HDMI-2 disconnected (normal left inverted right x axis y axis)
DP-1 connected primary 1440x900+0+0 (normal left inverted right x axis y axis) 408mm x 255mm
1440x900 59.89*+ 74.98
1280x1024 75.02 60.02
1152x864 75.00 67.02
1024x768 75.03 70.07 60.00
832x624 74.55
800x600 75.00 60.32 56.25
640x480 75.00 59.94
720x400 70.08
HDMI-3 disconnected (normal left inverted right x axis y axis)
DVI-D-1-0 disconnected (normal left inverted right x axis y axis)
HDMI-1-0 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 521mm x 293mm
1920x1080 60.00*+ 59.94 50.00 29.97 25.00 23.98 60.05 60.00 50.04
1680x1050 59.95
1600x900 60.00
1440x900 59.89
1366x768 59.79
1280x1024 75.02 60.02
1280x800 59.81
1280x720 60.00 59.94 50.00
1152x864 75.00
1024x768 75.03 70.07 60.00
800x600 75.00 72.19 60.32
720x576 50.00
720x480 59.94
640x480 75.00 72.81 59.94
DP-1-0 disconnected (normal left inverted right x axis y axis)
DP-1-1 disconnected (normal left inverted right x axis y axis)
1440x900 (0x46) 106.500MHz -HSync +VSync
h: width 1440 start 1520 end 1672 total 1904 skew 0 clock 55.93KHz
v: height 900 start 903 end 909 total 934 clock 59.89Hz
1280x1024 (0x47) 135.000MHz +HSync +VSync
h: width 1280 start 1296 end 1440 total 1688 skew 0 clock 79.98KHz
v: height 1024 start 1025 end 1028 total 1066 clock 75.02Hz
1280x1024 (0x48) 108.000MHz +HSync +VSync
h: width 1280 start 1328 end 1440 total 1688 skew 0 clock 63.98KHz
v: height 1024 start 1025 end 1028 total 1066 clock 60.02Hz
1152x864 (0x4a) 108.000MHz +HSync +VSync
h: width 1152 start 1216 end 1344 total 1600 skew 0 clock 67.50KHz
v: height 864 start 865 end 868 total 900 clock 75.00Hz
1024x768 (0x4c) 78.750MHz +HSync +VSync
h: width 1024 start 1040 end 1136 total 1312 skew 0 clock 60.02KHz
v: height 768 start 769 end 772 total 800 clock 75.03Hz
1024x768 (0x4d) 75.000MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1328 skew 0 clock 56.48KHz
v: height 768 start 771 end 777 total 806 clock 70.07Hz
1024x768 (0x4e) 65.000MHz -HSync -VSync
h: width 1024 start 1048 end 1184 total 1344 skew 0 clock 48.36KHz
v: height 768 start 771 end 777 total 806 clock 60.00Hz
800x600 (0x50) 49.500MHz +HSync +VSync
h: width 800 start 816 end 896 total 1056 skew 0 clock 46.88KHz
v: height 600 start 601 end 604 total 625 clock 75.00Hz
800x600 (0x51) 40.000MHz +HSync +VSync
h: width 800 start 840 end 968 total 1056 skew 0 clock 37.88KHz
v: height 600 start 601 end 605 total 628 clock 60.32Hz
640x480 (0x53) 31.500MHz -HSync -VSync
h: width 640 start 656 end 720 total 840 skew 0 clock 37.50KHz
v: height 480 start 481 end 484 total 500 clock 75.00Hz
640x480 (0x54) 25.175MHz -HSync -VSync
h: width 640 start 656 end 752 total 800 skew 0 clock 31.47KHz
v: height 480 start 490 end 492 total 525 clock 59.94HzOffline
#4 2024-05-20 20:12:07
- anarcobafif
- Member
- Registered: 2022-12-15
- Posts: 9
Re: Monitor detected and enabled but no signal after boot
$ nvidia-smi -q
==============NVSMI LOG==============
Timestamp : Mon May 20 17:07:18 2024
Driver Version : 550.78
CUDA Version : 12.4
Attached GPUs : 1
GPU 00000000:01:00.0
Product Name : NVIDIA GeForce GTX 1050 Ti
Product Brand : GeForce
Product Architecture : Pascal
Display Mode : Enabled
Display Active : Enabled
Persistence Mode : Disabled
Addressing Mode : N/A
MIG Mode
Current : N/A
Pending : N/A
Accounting Mode : Disabled
Accounting Mode Buffer Size : 4000
Driver Model
Current : N/A
Pending : N/A
Serial Number : N/A
GPU UUID : GPU-e675071f-73e1-4b99-befc-39508798f4a8
Minor Number : 0
VBIOS Version : 86.07.39.00.E9
MultiGPU Board : No
Board ID : 0x100
Board Part Number : N/A
GPU Part Number : 1C82-400-A1
FRU Part Number : N/A
Module ID : 1
Inforom Version
Image Version : G001.0000.01.04
OEM Object : 1.1
ECC Object : N/A
Power Management Object : N/A
Inforom BBX Object Flush
Latest Timestamp : N/A
Latest Duration : N/A
GPU Operation Mode
Current : N/A
Pending : N/A
GPU C2C Mode : N/A
GPU Virtualization Mode
Virtualization Mode : None
Host VGPU Mode : N/A
vGPU Heterogeneous Mode : N/A
GPU Reset Status
Reset Required : No
Drain and Reset Recommended : N/A
GSP Firmware Version : N/A
IBMNPU
Relaxed Ordering Mode : N/A
PCI
Bus : 0x01
Device : 0x00
Domain : 0x0000
Base Classcode : 0x3
Sub Classcode : 0x0
Device Id : 0x1C8210DE
Bus Id : 00000000:01:00.0
Sub System Id : 0x33511462
GPU Link Info
PCIe Generation
Max : 3
Current : 1
Device Current : 1
Device Max : 3
Host Max : 3
Link Width
Max : 16x
Current : 16x
Bridge Chip
Type : N/A
Firmware : N/A
Replays Since Reset : 0
Replay Number Rollovers : 0
Tx Throughput : 87 KB/s
Rx Throughput : 557 KB/s
Atomic Caps Inbound : N/A
Atomic Caps Outbound : N/A
Fan Speed : 0 %
Performance State : P8
Clocks Event Reasons
Idle : Active
Applications Clocks Setting : Not Active
SW Power Cap : Not Active
HW Slowdown : Not Active
HW Thermal Slowdown : Not Active
HW Power Brake Slowdown : Not Active
Sync Boost : Not Active
SW Thermal Slowdown : Not Active
Display Clock Setting : Not Active
Sparse Operation Mode : N/A
FB Memory Usage
Total : 4096 MiB
Reserved : 65 MiB
Used : 94 MiB
Free : 3939 MiB
BAR1 Memory Usage
Total : 256 MiB
Used : 13 MiB
Free : 243 MiB
Conf Compute Protected Memory Usage
Total : 0 MiB
Used : 0 MiB
Free : 0 MiB
Compute Mode : Default
Utilization
Gpu : 5 %
Memory : 7 %
Encoder : 0 %
Decoder : 0 %
JPEG : N/A
OFA : N/A
Encoder Stats
Active Sessions : 0
Average FPS : 0
Average Latency : 0
FBC Stats
Active Sessions : 0
Average FPS : 0
Average Latency : 0
ECC Mode
Current : N/A
Pending : N/A
ECC Errors
Volatile
Single Bit
Device Memory : N/A
Register File : N/A
L1 Cache : N/A
L2 Cache : N/A
Texture Memory : N/A
Texture Shared : N/A
CBU : N/A
Total : N/A
Double Bit
Device Memory : N/A
Register File : N/A
L1 Cache : N/A
L2 Cache : N/A
Texture Memory : N/A
Texture Shared : N/A
CBU : N/A
Total : N/A
Aggregate
Single Bit
Device Memory : N/A
Register File : N/A
L1 Cache : N/A
L2 Cache : N/A
Texture Memory : N/A
Texture Shared : N/A
CBU : N/A
Total : N/A
Double Bit
Device Memory : N/A
Register File : N/A
L1 Cache : N/A
L2 Cache : N/A
Texture Memory : N/A
Texture Shared : N/A
CBU : N/A
Total : N/A
Retired Pages
Single Bit ECC : N/A
Double Bit ECC : N/A
Pending Page Blacklist : N/A
Remapped Rows : N/A
Temperature
GPU Current Temp : 32 C
GPU T.Limit Temp : N/A
GPU Shutdown Temp : 102 C
GPU Slowdown Temp : 99 C
GPU Max Operating Temp : N/A
GPU Target Temperature : 83 C
Memory Current Temp : N/A
Memory Max Operating Temp : N/A
GPU Power Readings
Power Draw : N/A
Current Power Limit : 90.00 W
Requested Power Limit : 90.00 W
Default Power Limit : 90.00 W
Min Power Limit : 66.00 W
Max Power Limit : 113.00 W
GPU Memory Power Readings
Power Draw : N/A
Module Power Readings
Power Draw : N/A
Current Power Limit : N/A
Requested Power Limit : N/A
Default Power Limit : N/A
Min Power Limit : N/A
Max Power Limit : N/A
Clocks
Graphics : 139 MHz
SM : 139 MHz
Memory : 405 MHz
Video : 544 MHz
Applications Clocks
Graphics : N/A
Memory : N/A
Default Applications Clocks
Graphics : N/A
Memory : N/A
Deferred Clocks
Memory : N/A
Max Clocks
Graphics : 1974 MHz
SM : 1974 MHz
Memory : 3504 MHz
Video : 1708 MHz
Max Customer Boost Clocks
Graphics : N/A
Clock Policy
Auto Boost : N/A
Auto Boost Default : N/A
Voltage
Graphics : N/A
Fabric
State : N/A
Status : N/A
CliqueId : N/A
ClusterUUID : N/A
Health
Bandwidth : N/A
Processes
GPU instance ID : N/A
Compute instance ID : N/A
Process ID : 629
Type : G
Name : /usr/lib/Xorg
Used GPU Memory : 66 MiB
GPU instance ID : N/A
Compute instance ID : N/A
Process ID : 8628
Type : G
Name : /home/bafif/.local/share/Steam/ubuntu12_32/steam
Used GPU Memory : 1 MiB
GPU instance ID : N/A
Compute instance ID : N/A
Process ID : 9028
Type : G
Name : ./steamwebhelper
Used GPU Memory : 14 MiB$ nvidia-smi -q -u
==============NVSMI LOG==============
Timestamp : Mon May 20 17:09:44 2024
Driver Version : 550.78
CUDA Version : 12.4
HIC Info : N/A
Attached Units : 0Offline
#5 2024-05-20 20:46:57
- seth
- Member
- From: Won't reply 2 private help req
- Registered: 2012-09-03
- Posts: 75,287
Re: Monitor detected and enabled but no signal after boot
HDMI-1-0 is supposed to be enabled at 1920x1080 overlapping w/ the 1440x900 DP-1 when you called "xrandr -q"
At this point you got "no signal"?
How are you "only using my graphics card"? All the data you posted suggests both VGA devices are active (as they have to be since the DP is wired to the IGP)?
Offline
#6 2024-05-20 21:26:33
- anarcobafif
- Member
- Registered: 2022-12-15
- Posts: 9
Re: Monitor detected and enabled but no signal after boot
HDMI-1-0 is supposed to be enabled at 1920x1080 overlapping w/ the 1440x900 DP-1 when you called "xrandr -q"
At this point you got "no signal"?How are you "only using my graphics card"? All the data you posted suggests both VGA devices are active (as they have to be since the DP is wired to the IGP)?
I'm not only using my graphics card to make the outputs because I can't reach login console if I'm using only my GPU. I'm using Intel integrated graphics to have output in other monitor too. The system works exactly how it should but there is no ouput from the GPU and no power is being consumed. xrandr can effectively manage the display and move it from monitor to monitor but the HDMI-1-0 display seems to be as a phantom display.
I can use mons command to make a duplicate, to use only my secondary monitor (which is not connected to GPU) or to use only the main monitor (which is connected to GPU). If I move all the display to use only the main monitor, it disappears and I have to blindly open the terminal and execute mons -d command. I also tried by setting PEG as main from BIOS but that just makes every possible output disappear before login with no response, completely blind.
Offline
#7 2024-05-20 21:30:36
- anarcobafif
- Member
- Registered: 2022-12-15
- Posts: 9
Re: Monitor detected and enabled but no signal after boot
seth wrote:HDMI-1-0 is supposed to be enabled at 1920x1080 overlapping w/ the 1440x900 DP-1 when you called "xrandr -q"
At this point you got "no signal"?How are you "only using my graphics card"? All the data you posted suggests both VGA devices are active (as they have to be since the DP is wired to the IGP)?
I'm not only using my graphics card to make the outputs because I can't reach login console if I'm using only my GPU. I'm using Intel integrated graphics to have output in other monitor too. The system works exactly how it should but there is no ouput from the GPU and no power is being consumed. xrandr can effectively manage the display and move it from monitor to monitor but the HDMI-1-0 display seems to be as a phantom display.
I can use mons command to make a duplicate, to use only my secondary monitor (which is not connected to GPU) or to use only the main monitor (which is connected to GPU). If I move all the display to use only the main monitor, it disappears and I have to blindly open the terminal and execute mons -d command. I also tried by setting PEG as main from BIOS but that just makes every possible output disappear before login with no response, completely blind.
Before the problem, I've been using two monitors perfectly for about 2 months using Multi-Monitor feature from MSI BIOS and managing them via arandr.
Offline
#8 2024-05-20 21:32:15
- seth
- Member
- From: Won't reply 2 private help req
- Registered: 2012-09-03
- Posts: 75,287
Re: Monitor detected and enabled but no signal after boot
Ok, we'll need some data from the disbehaving system, though.
Start w/ the system journal and pot. xorg log - if you cannot ssh into the system (what would be ideal) reboot using the https://wiki.archlinux.org/title/Keyboa … el_(SysRq) and only boot into the multi-user.target.
The remaining xorg log will be that of the failing boot (if you reached X11) and
sudo journalctl -b -1 | curl -F 'file=@-' 0x0.stallows you to upload the system journal of the previous boot ("-1") into a pastebin service from the console.
Edit: please don't bump - edit you previous post if nobody has yet replied.
Also don't unconditionallly fully quote posts, you're just bloating the thread.
Last edited by seth (2024-05-20 21:33:32)
Offline