You are not logged in.

#1 2026-11-01 00:40:59

dhs
Member
Registered: 2014-02-25
Posts: 18

Problems with new installation

I just put archlinux on a new Dell machine.

If I bring up plasma on Wayland, I get a usableable system, including the KDE window manager -- but the display is just the upper left corner of the screen.  The display configuration window says the 1024x768 is the only resolution for this display (which it isn't -- it's 1920x1080).  I've tried creating a new mode using xrandr, and creating a file in xorg.conf.d -- both failed.

If I bring up plasma on X11, I get a full-screen display, and the display configuration window  shows a whole list of resolutions available -- but no window manager and various other problems (like it won't log out).

Any help appreciated, of course.  Thanks in advance.

Offline

#2 2026-11-01 02:22:53

cryptearth
Member
Registered: 2024-02-03
Posts: 2,389

Re: Problems with new installation

what hardware EXACTLY?
most important:
- desktop or laptop?
- igpu or dgpu?
- nvidia? which one? which package?

Offline

#3 2026-11-01 03:28:26

dhs
Member
Registered: 2014-02-25
Posts: 18

Re: Problems with new installation

It's a Dell Optiplex 7040 mini tower.  Intel Core i3 processor.  PCI Express x16 graphics adapter.
I think there are two different problems.  Wayland X misreads the monitor's data. X11 fails to load a window manager.

Offline

#4 2026-11-01 05:35:54

5hridhyan
Member
Registered: 2025-12-25
Posts: 1,122

Re: Problems with new installation

I thought KDE removed support for x11 sessions?
Anyways:

kscreen-doctor --outputs

It should list the name of each connected display (such as DP-1, HDMI-A-1), all modes it supports (if EDID is not read correctly, the list will be incomplete or contain only 1024x768), and the currently used mode...

And if your monitor's correct mode appears in the list (for example, numbered 0:1920x1080@60), you can force the setting using:

kscreen-doctor output.<output name>.mode.<mode number>

Edit:
run inxi -G or lspci -k | grep -A 2 -E "(VGA|3D)"
Does the journal show anything spicy?

Last edited by 5hridhyan (2026-11-01 05:52:03)


You'll definitely find me talking to a wall wink

Offline

#5 2026-11-01 09:21:11

seth
Member
From: Won't reply 2 private help req
Registered: 2012-09-03
Posts: 78,745

Re: Problems with new installation

Smells like you're running on the simplydumb device

PCI Express x16 graphics adapter.

Ok, but which one?
While lspci will answer that, just post your complete system journal for the boot:

sudo journalctl -b | nc termbin.com 9999

so we'll know what's going on on your system…

Offline

#6 Today 01:25:56

dhs
Member
Registered: 2014-02-25
Posts: 18

Re: Problems with new installation

I've been away for a couple days, so I apologize for the delay.
The journalctl output is at termbin.com/5plr
kscreen-doctor --outputs returns just the default resolution 1024x768.
The lspci output is:
  VGA compatible controller: Intel Corporation Skylake-S GT2 [HD Graphics 530] (rev06)
  DeviceName: Intel HD Graphics
  Subsystem: Dell Device 06b9

Last edited by dhs (Today 01:32:31)

Offline

Board footer

Powered by FluxBB