You are not logged in.
Pages: 1
Hi,
I've hot a problem with my wifi card on my asus A6JC
After boot, I type "dmesg"
ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.2.0dmpr
ipw3945: Copyright(c) 2003-2006 Intel Corporation
ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection
ipw3945: Detected geography ABG (13 802.11bg channels, 23 802.11a channels)
iwconfig:
lo no wireless extensions.
eth0 no wireless extensions.
eth1 no wireless extensions.
eth2 unassociated ESSID:off/any
Mode:Managed Frequency=nan kHz Access Point: Not-Associated
Bit Rate:0 kb/s Tx-Power:16 dBm
Retry limit:15 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:294 Missed beacon:0
My access point is detected by iwlist eth2 scan:
Cell 01 - Address: 00:06:25:49:C3:73
ESSID:"<hidden>"
Protocol:IEEE 802.11bg
Mode:Master
Channel:6
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Quality=90/100 Signal level=-42 dBm Noise level=-42 dBm
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
Extra: Last beacon: 7396ms ago
Here is my wpa_supplicant configuration (made with wpa_gui)
ctrl_interface=/var/run/wpa_supplicant
update_config=1
network={
ssid="reloaded"
psk="weareinthenetwork"
proto=RSN
key_mgmt=WPA-PSK
pairwise=CCMP
}
But, when i launch wpa_supplicant -Dwext -ieth2 -c/etc/wpa_supplicant.conf, i have this in dmesg
ADDRCONF(NETDEV_UP): eth2: link is not ready
And if I use wpa_gui :
ioctl[SIOCGIFADDR]: Cannot assign requested address
ioctl[SIOCGIFADDR]: Cannot assign requested address
ioctl[SIOCGIFADDR]: Cannot assign requested address
ioctl[SIOCGIFADDR]: Cannot assign requested address
ioctl[SIOCGIFADDR]: Cannot assign requested address
Any idea ?
Offline
Issue 'ifconfig eth2 up' beforehand.
1000
Offline
Already done ...
and still the same errors :
"ADDRCONF(NETDEV_UP): eth2: link is not ready" when I launch wpa_supplicant
and
"ioctl[SIOCGIFADDR]: Cannot assign requested address" when I launch wpa_gui
Offline
Have your tried assigning the essid manually using iwconfig yet? Might turn off the encryption temporarily on the access point to test to make sure you can connect without it. Might be worth it just to test it.
I am not familiar with wpa supplicant at all and have no plans to use it.
Offline
I downloaded wifi-radar, and it i'm able to connect with it ...
So I think there is a problem in my way of using wpa_supplicant... I will check later
[EDIT]
You got it shen
I must assign essid manually, using iwconfig.
Thanks a lot
Last edited by pfoo (2007-04-24 07:58:48)
Offline
Pages: 1