You are not logged in.

#1 2007-07-04 16:07:37

Wilku
Member
Registered: 2007-07-04
Posts: 41

[SOLVED]Warnings

Well I have a certain problem. When I start any application for the first time (first time after reboot) it starts up very slowly and I think it could be connected to the configuration of xorg. My video card is ATI Radeon 9550. The log file returns a few warnings and no errors. I would like to eliminate those warnings even if they are not connected with the starting speed of those applications/.

Warnings:

[root@haven wilku]# cat /var/log/Xorg.0.log | grep WW
        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
(WW) fglrx: No matching Device section for instance (BusID PCI:1:0:1) found
(WW) fglrx(0): board is an unknown third party board, chipset is supported
(WW) fglrx(0): Only one display is connnected,so single mode is enabled
(WW) LoadModule: given non-canonical module name "glesx.so"
(WW) fglrx(0): Option "VendorName" is not used
(WW) fglrx(0): Option "ModelName" is not used

Xorg.conf:

# File generated by xorgconfig.
#
# Copyright 2004 The X.Org Foundation
#
# Permission is hereby granted, free of charge, to any person obtaining a
# copy of this software and associated documentation files (the "Software"),
# to deal in the Software without restriction, including without limitation
# the rights to use, copy, modify, merge, publish, distribute, sublicense,
# and/or sell copies of the Software, and to permit persons to whom the
# Software is furnished to do so, subject to the following conditions:
# 
# The above copyright notice and this permission notice shall be included in
# all copies or substantial portions of the Software.
# 
# THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
# IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
# FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.  IN NO EVENT SHALL
# The X.Org Foundation BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
# WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF
# OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE
# SOFTWARE.
# 
# Except as contained in this notice, the name of The X.Org Foundation shall
# not be used in advertising or otherwise to promote the sale, use or other
# dealings in this Software without prior written authorization from
# The X.Org Foundation.
#
# **********************************************************************
# Refer to the xorg.conf(5) man page for details about the format of 
# this file.
# **********************************************************************
# **********************************************************************
# Module section -- this  section  is used to specify
# which dynamically loadable modules to load.
# **********************************************************************
#
# **********************************************************************
# Files section.  This allows default font and rgb paths to be set
# **********************************************************************
# **********************************************************************
# Server flags section.
# **********************************************************************
# **********************************************************************
# Input devices
# **********************************************************************
# **********************************************************************
# Core keyboard's InputDevice section
# **********************************************************************
# **********************************************************************
# Core Pointer's InputDevice section
# **********************************************************************
# **********************************************************************
# Other input device sections 
# this is optional and is required only if you
# are using extended input devices.  This is for example only.  Refer
# to the xorg.conf man page for a description of the options.
# **********************************************************************
#
# Section "InputDevice" 
#    Identifier  "Mouse2"
#    Driver      "mouse"
#    Option      "Protocol"      "MouseMan"
#    Option      "Device"        "/dev/mouse2"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball"
#    Driver     "magellan"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "spaceball2"
#    Driver     "spaceorb"
#    Option     "Device"        "/dev/cua0"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen0"
#    Driver     "microtouch"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "1412"
#    Option     "MaxX"          "15184"
#    Option     "MinY"          "15372"
#    Option     "MaxY"          "1230"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection
#
# Section "InputDevice"
#    Identifier "touchscreen1"
#    Driver     "elo2300"
#    Option     "Device"        "/dev/ttyS0"
#    Option     "MinX"          "231"
#    Option     "MaxX"          "3868"
#    Option     "MinY"          "3858"
#    Option     "MaxY"          "272"
#    Option     "ScreenNumber"  "0"
#    Option     "ReportingMode" "Scaled"
#    Option     "ButtonThreshold"       "17"
#    Option     "ButtonNumber"  "1"
#    Option     "SendCoreEvents"
# EndSection
# **********************************************************************
# Monitor section
# **********************************************************************
# Any number of monitor sections may be present
# **********************************************************************
# Graphics device section
# **********************************************************************
# Any number of graphics device sections may be present
# Standard VGA Device:
# Device configured by xorgconfig:
# **********************************************************************
# Screen sections
# **********************************************************************
# Any number of screen sections may be present.  Each describes
# the configuration of a single screen.  A single specific screen section
# may be specified from the X server command line with the "-screen"
# option.
# **********************************************************************
# ServerLayout sections.
# **********************************************************************
# Any number of ServerLayout sections may be present.  Each describes
# the way multiple screens are organised.  A specific ServerLayout
# section may be specified from the X server command line with the
# "-layout" option.  In the absence of this, the first section is used.
# When now ServerLayout section is present, the first Screen section
# is used alone.
 Section "DRI"
    Mode 0666
 EndSection

Section "ServerLayout"

# The Identifier line must be present
# Each Screen line specifies a Screen section name, and optionally
# the relative position of other screens.  The four names after
# primary screen name are the screens to the top, bottom, left and right
# of the primary screen.  In this example, screen 2 is located to the
# right of screen 1.
# Each InputDevice line specifies an InputDevice section name and
# optionally some options to specify the way the device is to be
# used.  Those options include "CorePointer", "CoreKeyboard" and
# "SendCoreEvents".
    Identifier     "Simple Layout"
    Screen      0  "aticonfig-Screen[0]" 0 0
    InputDevice    "Mouse1" "CorePointer"
    InputDevice    "Keyboard1" "CoreKeyboard"
EndSection

Section "Files"

# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.
#    RgbPath    "/usr/share/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
# 
# 
#    FontPath   "/usr/share/fonts/TTF"
#    FontPath   "/usr/share/fonts/Type1"
#    FontPath   "/usr/lib/X11/fonts/local/"
#    FontPath   "/usr/lib/X11/fonts/misc/"
#    FontPath   "/usr/lib/X11/fonts/75dpi/:unscaled"
#    FontPath   "/usr/lib/X11/fonts/100dpi/:unscaled"
#    FontPath   "/usr/lib/X11/fonts/Speedo/"
#    FontPath   "/usr/lib/X11/fonts/Type1/"
#    FontPath   "/usr/lib/X11/fonts/TrueType/"
#    FontPath   "/usr/lib/X11/fonts/freefont/"
#    FontPath   "/usr/lib/X11/fonts/75dpi/"
#    FontPath   "/usr/lib/X11/fonts/100dpi/"
# The module search path.  The default path is shown here.
#    ModulePath "/usr/lib/modules"
    FontPath     "/usr/share/fonts/misc"
#    FontPath     "/usr/share/fonts/100dpi:unscaled"
#    FontPath     "/usr/share/fonts/75dpi:unscaled"
EndSection

Section "Module"

# This loads the DBE extension module.
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
# This loads the font modules
#    Load        "type1"
# This loads the GLX module
    Load       "glx"
# This loads the DRI module
    Load       "dri"
    Load  "dbe"      # Double buffer extension
    SubSection "extmod"
        Option        "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection
    Load  "freetype"
#    Load        "xtt"
EndSection

Section "InputDevice"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.
#    Option     "Protocol"      "Xqueue"
#    Option    "Xleds"      "1 2 3"
#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    Option "XkbModel"    "pc105"
# If you have a US Microsoft Natural keyboard, you can use:
#    Option "XkbModel"    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    Option "XkbLayout"   "de"
# or:
#    Option "XkbLayout"   "de"
#    Option "XkbVariant"  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    Option "XkbOptions"  "ctrl:swapcaps"
# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"
#    Option "XkbModel"    "pc105"
#    Option "XkbLayout"   "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""
#    Option "XkbDisable"
    Identifier  "Keyboard1"
    Driver      "kbd"
    Option        "AutoRepeat" "500 30"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
    Option        "XkbRules" "xorg"
    Option        "XkbModel" "a4_rfkb23"
    Option        "XkbLayout" "pl"
EndSection

Section "InputDevice"

# Identifier and driver
# the following line.
#    Option "Protocol"    "Xqueue"
# Mouse-speed setting for PS/2 mouse.
#    Option "Resolution"    "256"
# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.
#    Option "BaudRate"    "9600"
#    Option "SampleRate"    "150"
# Mouse wheel mapping.  Default is to map vertical wheel to buttons 4 & 5,
# horizontal wheel to buttons 6 & 7.   Change if your mouse has more than
# 3 buttons and you need to map the wheel to different button ids to avoid
# conflicts.
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
    Identifier  "Mouse1"
    Driver      "mouse"
    Option        "Protocol" "Auto"    # Auto detect
    Option        "Device" "/dev/input/mice"
# When using XQUEUE, comment out the above two lines, and uncomment
    Option        "ZAxisMapping" "4 5 6 7"
# Emulate3Buttons is an option for 2-button mice
    Option        "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"
# ChordMiddle is an option for some 3-button Logitech mice
#    Option "ChordMiddle"
EndSection

Section "Monitor"

# HorizSync is in kHz unless units are specified.
# HorizSync may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
#    HorizSync    30-64         # multisync
#    HorizSync    31.5, 35.2    # multiple fixed sync frequencies
#    HorizSync    15-25, 30-50  # multiple ranges of sync frequencies
# VertRefresh is in Hz unless units are specified.
# VertRefresh may be a comma separated list of discrete values, or a
# comma separated list of ranges of values.
# NOTE: THE VALUES HERE ARE EXAMPLES ONLY.  REFER TO YOUR MONITOR'S
# USER MANUAL FOR THE CORRECT NUMBERS.
    Identifier   "My Monitor"
    HorizSync    31.5 - 82.0
    VertRefresh  40.0 - 150.0
EndSection

Section "Monitor"
    Identifier   "aticonfig-Monitor[0]"
    Option        "VendorName" "ATI Proprietary Driver"
    Option        "ModelName" "Generic Autodetecting Monitor"
    Option        "DPMS" "true"
EndSection

Section "Device"

# The chipset line is optional in most cases.  It can be used to override
# the driver's chipset detection, and should not normally be specified.
#    Chipset    "generic"
# The Driver line must be present.  When using run-time loadable driver
# modules, this line instructs the server to load the specified driver
# module.  Even when not using loadable driver modules, this line
# indicates which driver should interpret the information in this section.
# The BusID line is used to specify which of possibly multiple devices
# this section is intended for.  When this line isn't present, a device
# section can only match up with the primary video device.  For PCI
# devices a line like the following could be used.  This line should not
# normally be included unless there is more than one video device
# intalled.
#    BusID      "PCI:0:10:0"
#    VideoRam    256
#    Clocks    25.2 28.3
    Identifier  "Standard VGA"
    Driver      "vga"
    VendorName  "Unknown"
    BoardName   "Unknown"
EndSection

Section "Device"

    #VideoRam    131072
    # Insert Clocks lines here if appropriate
    Identifier  "** ATI Radeon (generic)               [radeon]"
    Driver      "fglrx"
EndSection

Section "Device"
    Identifier  "aticonfig-Device[0]"
    Driver      "fglrx"
    BusID       "PCI:1:0:0"
EndSection

Section "Screen"
    Identifier "Screen 1"
    Device     "** ATI Radeon (generic)               [radeon]"
    Monitor    "My Monitor"
    DefaultDepth     24
    SubSection "Display"
        Viewport   0 0
        Depth     8
        Modes    "1280x1024" "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     16
        Modes    "1280x1024" "1024x768" "800x600" "640x480"
    EndSubSection
    SubSection "Display"
        Viewport   0 0
        Depth     24
        Modes    "1280x1024" "1024x768" "800x600" "640x480"
    EndSubSection
EndSection

Section "Screen"
    Identifier "aticonfig-Screen[0]"
    Device     "aticonfig-Device[0]"
    Monitor    "aticonfig-Monitor[0]"
    DefaultDepth     24
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

Section "Extensions"
        Option  "Composite" "False"
EndSection

Section "ServerFlags"
        Option "AIGLX" "off"
EndSection

I will be greatful for any assistance.

Wilku

Last edited by Wilku (2007-07-10 15:37:57)

Offline

#2 2007-07-04 17:15:28

Cerebral
Forum Fellow
From: Waterloo, ON, CA
Registered: 2005-04-08
Posts: 3,108
Website

Re: [SOLVED]Warnings

I've seen this problem caused by not having localhost properly defined in /etc/hosts - can you post that file?

Offline

#3 2007-07-04 20:14:57

Wilku
Member
Registered: 2007-07-04
Posts: 41

Re: [SOLVED]Warnings

#
# /etc/hosts: static lookup table for host names
#

#<ip-address>    <hostname.domain.org>    <hostname>
127.0.0.1        localhost.localdomain    localhost

# End of file

Offline

#4 2007-07-04 22:03:12

nikron
Member
Registered: 2007-05-15
Posts: 130

Re: [SOLVED]Warnings

add whatever the name of your computer is to the end of that then.

Offline

#5 2007-07-05 18:26:53

Wilku
Member
Registered: 2007-07-04
Posts: 41

Re: [SOLVED]Warnings

I changed my hosts file to:

#
# /etc/hosts: static lookup table for host names
#

#<ip-address>   <hostname.domain.org>   <hostname>
127.0.0.1               localhost.localdomain   localhost
haven
# End of file

haven - name of my computer

Nothing changed

Offline

#6 2007-07-05 18:44:35

Cerebral
Forum Fellow
From: Waterloo, ON, CA
Registered: 2005-04-08
Posts: 3,108
Website

Re: [SOLVED]Warnings

Wilku wrote:

I changed my hosts file to:
..
Nothing changed

The previous poster was unclear - what you want is this:

#
# /etc/hosts: static lookup table for host names
#

#<ip-address>   <hostname.domain.org>   <hostname>
127.0.0.1               localhost.localdomain   localhost haven
# End of file

(by the way, I see nothing wrong with those warnings - afaik they're fairly harmless)

Last edited by Cerebral (2007-07-05 18:45:32)

Offline

#7 2007-07-05 20:26:20

dolby
Member
From: 1992
Registered: 2006-08-08
Posts: 1,581

Re: [SOLVED]Warnings

isnt this supposed to be

127.0.0.1               haven.localdomain   haven

?


There shouldn't be any reason to learn more editor types than emacs or vi -- mg (1)
[You learn that sarcasm does not often work well in international forums.  That is why we avoid it. -- ewaller (arch linux forum moderator)

Offline

#8 2007-07-05 20:52:21

Cerebral
Forum Fellow
From: Waterloo, ON, CA
Registered: 2005-04-08
Posts: 3,108
Website

Re: [SOLVED]Warnings

dolby wrote:

isnt this supposed to be

127.0.0.1               haven.localdomain   haven

?

Not to my knowledge - you definitely still want the localhost name mapping to 127.0.0.1

Offline

#9 2007-07-06 07:54:00

Wilku
Member
Registered: 2007-07-04
Posts: 41

Re: [SOLVED]Warnings

None of the options presented above helped;/

Cerebral wrote:

(by the way, I see nothing wrong with those warnings - afaik they're fairly harmless)

Well I believe that those warnings are the reason for my 'launch' problem. As I said, every time I run an application for the first time it starts ages.

Do you know of anything else that can cause such problems?

Last edited by Wilku (2007-07-06 08:58:41)

Offline

#10 2007-07-06 18:26:30

Cerebral
Forum Fellow
From: Waterloo, ON, CA
Registered: 2005-04-08
Posts: 3,108
Website

Re: [SOLVED]Warnings

Wilku wrote:

Well I believe that those warnings are the reason for my 'launch' problem. As I said, every time I run an application for the first time it starts ages.

Well, let's go through them:

(WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)

It can't open ACPI; not unusual if you're not running acpid.

(WW) fglrx: No matching Device section for instance (BusID PCI:1:0:1) found

Normal - if you only have a single monitor but a card with multiple outputs this is expected.  I get it all the time.

(WW) fglrx(0): board is an unknown third party board, chipset is supported

No problem here - it just means that your board is third-party but it's still supported by the driver.

(WW) fglrx(0): Only one display is connnected,so single mode is enabled

Again, normal if you only have one monitor connected.

(WW) LoadModule: given non-canonical module name "glesx.so"

Haven't seen this before, but it seems harmles - just saying that it's asked to load an unusual module name.

(WW) fglrx(0): Option "VendorName" is not used
(WW) fglrx(0): Option "ModelName" is not used

These options aren't used by the fglrx driver, and it's telling you that.

Are there any errors (EE) in your log?  Is there any difference if you try the free 'radeon' driver instead of the proprietary 'fglrx' one?

Offline

#11 2007-07-10 15:37:27

Wilku
Member
Registered: 2007-07-04
Posts: 41

Re: [SOLVED]Warnings

Now I understand the irrelevance of those warnings to my problem. Thank you.

Offline

#12 2007-07-10 15:47:55

Cerebral
Forum Fellow
From: Waterloo, ON, CA
Registered: 2005-04-08
Posts: 3,108
Website

Re: [SOLVED]Warnings

Ah, I see in your original post there are no errors in your log - sorry I missed that before.    I'm still curious if using the free 'radeon' driver (available in the packages xf86-video-ati and libgl-dri  -- you'll need to uninstall fgrlx first) works better than the fglrx driver for you.

Also, that xorg.conf looks pretty messy - I've cleaned it up a bit for you here.  It should do exactly the same as the one you posted, but it's easier to read and follow.  If you decide to use it, back up your existing one first, just in case I've buggered something up. wink

Section "DRI"
   Mode 0666
EndSection

Section "ServerLayout"
    Identifier     "Simple Layout"
    Screen      0  "aticonfig-Screen[0]" 0 0
    InputDevice    "Mouse1" "CorePointer"
    InputDevice    "Keyboard1" "CoreKeyboard"
EndSection

Section "Files"
# The location of the RGB database.  Note, this is the name of the
# file minus the extension (like ".txt" or ".db").  There is normally
# no need to change the default.
#    RgbPath    "/usr/share/X11/rgb"
# Multiple FontPath entries are allowed (which are concatenated together),
# as well as specifying multiple comma-separated entries in one FontPath
# command (or a combination of both methods)
    FontPath     "/usr/share/fonts/misc"
EndSection

Section "Module"
# This loads the font modules
#    Load        "type1"
# This loads the GLX module
    Load       "glx"
# This loads the DRI module
    Load       "dri"
# This loads the DBE extension module.
    Load  "dbe"      # Double buffer extension
# This loads the miscellaneous extensions module, and disables
# initialisation of the XFree86-DGA extension within that module.
    SubSection "extmod"
        Option        "omit xfree86-dga"   # don't initialise the DGA extension
    EndSubSection
    Load  "freetype"
#    Load        "xtt"
EndSection

Section "InputDevice"

# For most OSs the protocol can be omitted (it defaults to "Standard").
# When using XQUEUE (only for SVR3 and SVR4, but not Solaris),
# uncomment the following line.
#    Option     "Protocol"      "Xqueue"
#    Option    "Xleds"      "1 2 3"
#    Option "LeftAlt"     "Meta"
#    Option "RightAlt"    "ModeShift"
# To customise the XKB settings to suit your keyboard, modify the
# lines below (which are the defaults).  For example, for a non-U.S.
# keyboard, you will probably want to use:
#    Option "XkbModel"    "pc105"
# If you have a US Microsoft Natural keyboard, you can use:
#    Option "XkbModel"    "microsoft"
#
# Then to change the language, change the Layout setting.
# For example, a german layout can be obtained with:
#    Option "XkbLayout"   "de"
# or:
#    Option "XkbLayout"   "de"
#    Option "XkbVariant"  "nodeadkeys"
#
# If you'd like to switch the positions of your capslock and
# control keys, use:
#    Option "XkbOptions"  "ctrl:swapcaps"
# These are the default XKB settings for Xorg
#    Option "XkbRules"    "xorg"
#    Option "XkbModel"    "pc105"
#    Option "XkbLayout"   "us"
#    Option "XkbVariant"  ""
#    Option "XkbOptions"  ""
#    Option "XkbDisable"
    Identifier  "Keyboard1"
    Driver      "kbd"
    Option        "AutoRepeat" "500 30"
# Specify which keyboard LEDs can be user-controlled (eg, with xset(1))
    Option        "XkbRules" "xorg"
    Option        "XkbModel" "a4_rfkb23"
    Option        "XkbLayout" "pl"
EndSection

Section "InputDevice"

# Identifier and driver
# the following line.
#    Option "Protocol"    "Xqueue"
# Mouse-speed setting for PS/2 mouse.
#    Option "Resolution"    "256"
# Baudrate and SampleRate are only for some Logitech mice. In
# almost every case these lines should be omitted.
#    Option "BaudRate"    "9600"
#    Option "SampleRate"    "150"
# Mouse wheel mapping.  Default is to map vertical wheel to buttons 4 & 5,
# horizontal wheel to buttons 6 & 7.   Change if your mouse has more than
# 3 buttons and you need to map the wheel to different button ids to avoid
# conflicts.
# Emulate3Timeout is the timeout in milliseconds (default is 50ms)
    Identifier  "Mouse1"
    Driver      "mouse"
    Option        "Protocol" "Auto"    # Auto detect
    Option        "Device" "/dev/input/mice"
# When using XQUEUE, comment out the above two lines, and uncomment
    Option        "ZAxisMapping" "4 5 6 7"
# Emulate3Buttons is an option for 2-button mice
    Option        "Emulate3Buttons"
#    Option "Emulate3Timeout"    "50"
# ChordMiddle is an option for some 3-button Logitech mice
#    Option "ChordMiddle"
EndSection

Section "Monitor"
    Identifier   "aticonfig-Monitor[0]"
    Option        "VendorName" "ATI Proprietary Driver"
    Option        "ModelName" "Generic Autodetecting Monitor"
    Option        "DPMS" "true"
EndSection

Section "Device"
    Identifier  "aticonfig-Device[0]"
    Driver      "fglrx"
    BusID       "PCI:1:0:0"
EndSection

Section "Screen"
    Identifier "aticonfig-Screen[0]"
    Device     "aticonfig-Device[0]"
    Monitor    "aticonfig-Monitor[0]"
    DefaultDepth     24
    SubSection "Display"
        Viewport   0 0
        Depth     24
    EndSubSection
EndSection

Section "Extensions"
        Option  "Composite" "False"
EndSection

Section "ServerFlags"
        Option "AIGLX" "off"
EndSection

I've stripped out sections that were never used.  Hopefully I got it right. wink

Offline

Board footer

Powered by FluxBB