Greetings and thank you for allowing me to join the forum! I actually
have a fairly decent install on a Dell Latitude c610, dual booted with
Windows 2000. Grub works just fine. Quick question:
When Arch first starts booting up is there anyway to slow down or pause
the screen? It's going by so fast I can't read what it's saying. I don't see
any error messages, but again it's going by too fast.
Thank you -- Larry
if i am not mistaken you can often get some if not all of the information from booting from running dmesg. any daemon or module errors will often be displayed in the logs (ie x logs).
I am not your friend
Thanks sarah31. I just installed the base system, still in text mode, nothing fancy installed yet. There is something in the last section --
something like /dev/discs/disk0/part2 is not a directory? I don't always know what I looking at, still a newbie. I just wanted to have everything right before I started with xfree config, kde etc. Anyway thanks for dmesg,
but nothing shows up there. Maybe everything is ok? The partition table looks fine. -- Thanks again for the reply. -- Larry
what do you part2? perhaps there is a minor syntax error in one of your config files. but i would not be to concerned if you can navigate through the diretory tree, your user works and you can access part2 (which i am assuming is either your swap or /home)
I am not your friend
To prevent that the screen is cleared after bootup, remove the first char or so from /etc/issue.
I guess that you switched the mountpoint with the device in your fstab.
Thanks again sarah31--My partition table is:
I'm not that familiar with this system, but /etc/fstab looks OK too.
I recently finished installing Gentoo. This system looks totally different.
I thought they all looked basically the same.
Anyway the message is:
mount: mount point /dev/discs/disk0/part2 is not a directory.
Again, everything seems to be OK, but I would'nt know until something goes wrong. Thanks again -- Larry
sarah31 just noticed sometning in fstab:
/dev/discs/disc0/part3 swap swap defaults 0 0
/dev/discs/disc0/part4 / reiserfs defaults 0 0
/dev/discs/disc0/part2 /dev/discs/disc0/part2 ext2 defaults 0 1
Why is /dev/discs/disc0/part2 listed twice???-- Larry
Are you able to access /boot ??..since you say that that parition is your boot partition
Errr..if you can't access /boot...try changing the messed up line in your fstab to read
/dev/discs/disc0/part2 /boot ext2 defaults 0 1
it is likely that you will boot fine, but be unable to update the contents of /boot (ie install a new kernel) until you fix your fstab like cobalt suggested..
"tacos" -- Cactus' Law
"t̥͍͎̪̪͗a̴̻̩͈͚ͨc̠o̩̙͈ͫͅs͙͎̙͊ ͔͇̫̜t͎̳̀a̜̞̗ͩc̗͍͚o̲̯̿s̖̣̤̙͌ ̖̜̈ț̰̫͓ạ̪͖̳c̲͎͕̰̯̃̈o͉ͅs̪ͪ ̜̻̖̜͕" -- -̖͚̫̙̓-̺̠͇ͤ̃ ̜̪̜ͯZ͔̗̭̞ͪA̝͈̙͖̩L͉̠̺͓G̙̞̦͖O̳̗͍
Greetings again! I changed that line and the mount message is gone.
I see no error messages in boot-up or dmesg so I guess everything
is fine. Thank you to sarah31, i3839, cobalt & cactus. -- Larry