Arch Linux

Reasons

Member

From: Washington

Registered: 2007-11-04

Posts: 572

Big idiot question

Anytime I run something, it runs fine but I get:

warning: current locale is invalid; using default "C" locale

I read the wiki on what to do; however, my /etc/locale.gen is blank and locale-gen does nothing.

rc.conf

#
# /etc/rc.conf - Main Configuration for Arch Linux
#

#
# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="en_US.utf8"
HARDWARECLOCK="localtime"
TIMEZONE="Canada/Pacific"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"

#
# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by udev
MOD_BLACKLIST=()
#
# Modules to load at boot-up (in this order)
#   - prefix a module with a ! to blacklist it
#
MODULES=(sky2 iwl4965 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"

#
# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
HOSTNAME="reasons"
#
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
# interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
#   - prefix an entry in INTERFACES with a ! to disable it
#   - no hyphens in your interface names - Bash doesn't like it
#
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
#
lo="lo 127.0.0.1"
eth0="dhcp"
wlan0="dhcp"
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
INTERFACES=(lo eth0 wlan0)
#
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
#   - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
#
# Enable these network profiles at boot-up.  These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
#   - set to 'menu' to present a menu during boot-up (dialog package required)
#   - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network-profiles
#
#NET_PROFILES=(home)

#
# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
#   - prefix a daemon with a ! to disable it
#   - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng dbus netfs hal @network @iwl496 @wicd @slim @crond @alsa @cups @mpd)


# End of file

Last edited by Reasons (2007-12-18 04:22:40)

fwojciec

Member

Registered: 2007-05-20

Posts: 1,411

Re: Big idiot question

try reinstalling "glibc", the file /etc/locale.gen is a part of this package.  it is possible that pacman will install the new version of this file as locale.gen.pacnew - if so rename it to locale.gen and follow the wiki to set your locale.

Allan

Pacman

From: Brisbane, AU

Registered: 2007-06-09

Posts: 11,482

Website

Re: Big idiot question

Reinstall glibc. Uncomment  "en_US.UTF-8 UTF-8" in /etc/locale.gen and run "locale-gen"

Last edited by Allan (2007-12-18 04:39:25)

---

PGP Key: F99FFE0FEAE999BD | I develop pacman - buy me a drink!

Reasons

Member

From: Washington

Registered: 2007-11-04

Posts: 572

Re: Big idiot question

Thanks guys, that did it.