You are not logged in.

#1 2004-07-25 13:12:14

sykotik
Member
Registered: 2004-06-15
Posts: 49

Compaq Multiport Evo n800c wlan help needed(long)

I am having problems getting my wireless network module working.  I ran the hotplug script when i first attempted to get this working.  The difference with the multiport card, is that to initially enable the device one must enable it by pressing, function(Fn)+F2.

When i enable the device with this key press i notice that the prism2_usb module is loaded via lsmod.

prism2_usb             76932  0 
p80211                 32272  1 prism2_usb

When i researched the module needed for this multiport device, there are many different opinions on compaq multiports, as well as many problems with them.  The Orinocco modules and and Prism modules were mentioned as "working" modules(via hp linux forums/googling/mailing lists).

I assumed that the prism modules were the correct ones to use, since they are loaded when the device is enabled(i assumed these modules were selected by hotplug). Maybe this is where I am wrong, but moving on.

I then downloaded the wirelesstools package so that i can utilize the command iwconfig, and to help with wlan devices.

Im very new to arch-linux, so I dont know where to go at this point. The wireless networking does not work with this module loaded.

iwconfig

lo        no wireless extensions.

sit0      no wireless extensions.

eth0      no wireless extensions.

wlan0     no wireless extensions.

ifconfig -a

wlan0 Link encap:Ethernet  HWaddr 00:00:00:00:00:00  
          BROADCAST NOTRAILERS MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

I do think something is wrong with the module maybe, because of the fact that no hardware address is represented.  I could be wrong being that im new to arch/linux.  But again I do not know how the multiport modules from compaq work.

/etc/rc.d/wlan start

Starting WLAN Devices: FATAL: Module wlan0 not found.
FATAL: Module wlan0 not found.
message=lnxreq_ifstate
  ifstate=fwload
  resultcode=implementation_failure
prism2dl: No such device
load_cardpda failed, exiting.
Unknown prism2 hardware type  (), assuming SSF
Processing PDR file: /tmp/prism2_ssf.pda
prism2dl: No such device
Couldn't fetch PRI-SUP info
Warning: RAM load only, PDA changes will NOT be written to flash.
Reading S-record file /etc/wlan//prism2_pm.hex...
NIC ID: 0 v0.0.0
MFI ID: 0 v0 0->0
CFI ID: 0 v0 0->0
PRI ID: 0 v0 0->0
Version:  ID 0x15 1.1.2
Compat: Role 0 Id 0x3 v2 4->4
Compat: Role 0x1 Id 0x2 v2 1->1
Seq: 0
Platform:  ID 0x800e 1.0.0
Platform:  ID 0x8015 1.0.0
Platform:  ID 0x8019 1.0.0
Platform:  ID 0x801d 1.0.0
Platform:  ID 0x8024 1.0.0
prism2dl: warning: Failed to find PDR for plugrec 0x0003.
prism2dl: warning: Failed to find PDR for plugrec 0x0005.
prism2dl: warning: Failed to find PDR for plugrec 0x0006.
prism2dl: warning: Failed to find PDR for plugrec 0x0007.
prism2dl: warning: Failed to find PDR for plugrec 0x0008.
prism2dl: warning: Failed to find PDR for plugrec 0x0402.
prism2dl: warning: Failed to find PDR for plugrec 0x0403.
prism2dl: warning: Failed to find PDR for plugrec 0x0404.
prism2dl: warning: Failed to find PDR for plugrec 0x0408.
prism2dl: warning: Failed to find PDR for plugrec 0x0001.
prism2dl: No such device
prism2dl: writeimage()->do_ioctl() failed w/ result=19, aborting download
prism2dl: Failed to ramwrite image data for /etc/wlan//prism2_pm.hex, exiting.
prism2dl: No such device
load_cardpda failed, exiting.
Firmware failed to load for device wlan0

This makes me further the thought of the module not being correct, because the wlan0 device is not even recognized.

Now that I think the module is wrong I rmmod the modules Ithat were loaded when powering on the device.(prism2_usb/p80211).  I then load the orinoco modules via modprobe orinoco.

lsmod

orinoco                44428  0 
hermes                  8320  1 orinoco

iwconfig

lo        no wireless extensions.

sit0      no wireless extensions.

eth0      no wireless extensions.

/etc/rc.d/wlan start

Starting WLAN Devices: FATAL: Module wlan0 not found.
FATAL: Module wlan0 not found.
Error: Device wlan0 does not seem to be present.
Make sure you've inserted the appropriate
modules or that your modules.conf file contains
the appropriate aliase(s).

I do have to most recent wlan-ng26 drivers: wlancfg version: 0.2.1-pre21

I tried to figure out the exact chipset but I had no luck with this, since the multiport device is on a usb hub/uses usb.  So this device was not listed in lspic, and I have the ohci-hcd module loaded via rc.conf.

I also have included the line, wlan0="dhcp" n INTERFACES=(lo eth0 wlan0), in my rc.conf.

Which brings me here, with no idea of what to try to do.  I hope I have included enough information.  If anyone needs any more information I will gladly provide it.  Any help would be greatly appreciated.

Offline

#2 2004-08-02 18:13:20

sykotik
Member
Registered: 2004-06-15
Posts: 49

Re: Compaq Multiport Evo n800c wlan help needed(long)

anyone  sad

Offline

#3 2004-08-02 18:51:17

dp
Member
From: Zürich, Switzerland
Registered: 2003-05-27
Posts: 3,378
Website

Re: Compaq Multiport Evo n800c wlan help needed(long)

i0m also relatively newbie for wireless, but at least i have mine working

what i wonder about your config, is, why do you use wlan0 ?

i myself have eth0 (normal, using e100), eth1 (firewire), eth2 (wireless, using orinoco_pci) and it seems to work like this:

modprobe orinoco_pci 

(what is managed for you with hotplug, hopefully)

then

iwconfig ......

using all options needed for the net i want to login

then

dhcpcd eth2

and then it works simply

so i have nowhere wlan0, but i don't use hotplug for this

anyone knowning more feel free to correct me :-)


The impossible missions are the only ones which succeed.

Offline

#4 2004-11-23 05:51:22

Corneliax
Member
From: Indianapolis, IN
Registered: 2004-04-27
Posts: 43
Website

Re: Compaq Multiport Evo n800c wlan help needed(long)

Offline

Board footer

Powered by FluxBB