You are not logged in.
I reinstalled arch last night, and now I can't get my sound working correctly anymore. It worked fine before the reinstall, so I'm hoping its just a config problem somewhere.
I have an Maudio Revolution 5.1, running alsa, using snd-ice1724
When I boot up, Sound only comes from the right speaker. I know of the bug with alsa that has the left channel muted on boot, and a simple toggle of a mixer would fix the problem, but it's not, it seems like my speaker is permanently muted. I cannot toggle mute/unmute because it's not accepted in alsamixer.
I know this isn't a hardware problem because if I move my speakers around, the right channel is muted.
Last edited by heleos (2008-07-11 18:21:48)
Offline
This will sound really dumb, but are your speakers plugged in all the way? A friend of mine lived with only his right channel for 2 months before he realized they weren't plugged in all the way.
Offline
Unfortunately they are
Offline
Are all the volume settings unmuted? Some sound cards have separate sliders for L,R, Center, Bass, etc.
Offline
As far as I know they are. ice1724 doesn't allow muting of PCM, which is what it uses for the main sound
Offline
shameless bump... (and a better title)
Offline
run 'alsamixer' and make sure none of the settings have "OM" or "MO" instead of "OO". Use the ">" key to toggle it
[home page] -- [code / configs]
"Once you go Arch, you must remain there for life or else Allan will track you down and break you."
-- Bregol
Offline
They don't.
here's a horrible copy/paste from alsamixer:
┌──────────────────[AlsaMixer v1.0.16 (Press Escape to quit)]──────────────────┐
│ Card: M Audio Revolution-5.1 │
│ Chip: ICE1724 - multitrack │
│ View: [Playback] Capture All │
│ Item: PCM [dB gain=-13.50, -13.50]
│ │
│ ┌──┐ ┌──┐ ┌──┐ ┌──┐ ┌──┐ ┌──┐ ┌──┐ │
│ │ │ │ │ │ │ │ │ │▒▒│ │▒▒│ │▒▒│ │
│ │ │ │ │ │ │ │ │ │▒▒│ │▒▒│ │▒▒│ │
│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ >
│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ >
│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ >
│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ >
│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ >
│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ >
│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │
│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │
│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ │▒▒│ PCM Out │
│ └──┘ └──┘ └──┘ └──┘ └──┘ └──┘ └──┘ │
│ │
│
│ 79<>79 80 80 80<>80 100<>100 100<>100 100<>100 │
│ < PCM >PCM Cent PCM LFE PCM Rear Line Loo CD Loopb Mic Loop IEC958
PCM is the channel I used to toggle to get sound working in both speakers.
Last edited by heleos (2008-07-10 20:39:48)
Offline
I found them problem...
revo 5.1 has a bunch of channels toward the end of alsamixer:
[H/W] [H/W 1] [H/W 2] [H/W 3] [H/W 4] [H/W 5]
A couple of them were set to "IEC958 In L" or "IEC958 In R"
I set them all to "PCM OUT" and sound comes out of both speakers... but it sounds a little bad. Does anyone have these channels in their alsamixer, and if so, could you post what you have for values? I'm guessing its a combination of L and R instead of all PCM OUT
Offline