You are not logged in.
- Topics: Active | Unanswered
#1 2008-08-03 16:02:22
- jordanwb
- Member
- From: Ontario, Canada
- Registered: 2008-07-01
- Posts: 151
Set gateway IP with ifconfig
I figured out how to set netmask and IP with ifconfig: ifconfig -a eth0 192.168.1.132 netmask 255.255.255.128 But how do I set the gateway IP with ifconfig?
Last edited by jordanwb (2008-08-03 16:10:00)
Offline
#2 2008-08-03 16:12:27
- lucke
- Member
- From: Poland
- Registered: 2004-11-30
- Posts: 4,018
Re: Set gateway IP with ifconfig
"route add"
Offline
#3 2008-08-03 16:56:07
- jordanwb
- Member
- From: Ontario, Canada
- Registered: 2008-07-01
- Posts: 151
Re: Set gateway IP with ifconfig
So I put "route add -net 192.168.1.0 netmask 255.255.255.128 gw 192.168.1.129 dev eth0"
and I get "SIOCADDRT: No such process"
Last edited by jordanwb (2008-08-03 16:59:57)
Offline
#4 2008-08-03 16:58:20
- wonder
- Developer
- From: Bucharest, Romania
- Registered: 2006-07-05
- Posts: 5,941
- Website
Re: Set gateway IP with ifconfig
route add default gw 192.168.1.129
Last edited by wonder (2008-08-03 16:58:48)
Give what you have. To someone, it may be better than you dare to think.
Offline
#5 2008-08-03 17:00:55
- jordanwb
- Member
- From: Ontario, Canada
- Registered: 2008-07-01
- Posts: 151
Re: Set gateway IP with ifconfig
Thanks
Last edited by jordanwb (2008-08-03 17:07:39)
Offline
#6 2008-08-03 17:06:20
- wonder
- Developer
- From: Bucharest, Romania
- Registered: 2006-07-05
- Posts: 5,941
- Website
Re: Set gateway IP with ifconfig
after setting ip for eth0 do you do "ifconfig eth0 up" ?
Give what you have. To someone, it may be better than you dare to think.
Offline
#7 2008-08-03 17:08:12
- jordanwb
- Member
- From: Ontario, Canada
- Registered: 2008-07-01
- Posts: 151
Re: Set gateway IP with ifconfig
I forgot to re-set the IP for eth0 when I booted. It works now. Also is there a command that I could use to show the free space on a given partition?
Last edited by jordanwb (2008-08-03 17:11:48)
Offline
#8 2008-08-03 17:12:29
- wonder
- Developer
- From: Bucharest, Romania
- Registered: 2006-07-05
- Posts: 5,941
- Website
Re: Set gateway IP with ifconfig
df -h
Give what you have. To someone, it may be better than you dare to think.
Offline
#9 2008-08-03 17:15:24
- jordanwb
- Member
- From: Ontario, Canada
- Registered: 2008-07-01
- Posts: 151
Re: Set gateway IP with ifconfig
Thanks. Wow I've used 28% of my 2Gig flash drive. I hope xorg and kde will fit.
Offline
#10 2008-08-03 17:22:51
- lucke
- Member
- From: Poland
- Registered: 2004-11-30
- Posts: 4,018
Re: Set gateway IP with ifconfig
You might have a look at FaunOS or Larch if you plan to run Arch on a usb stick.
Offline
#11 2008-08-03 17:27:11
- jordanwb
- Member
- From: Ontario, Canada
- Registered: 2008-07-01
- Posts: 151
Re: Set gateway IP with ifconfig
I already have Arch installed on my flash drive. I created a ext2 partition, flipped the bootable flag and ran the arch setup as normal. I'd rather start with the console and build up, installing what I want.
Offline
#12 2008-08-03 17:35:38
- lucke
- Member
- From: Poland
- Registered: 2004-11-30
- Posts: 4,018
Re: Set gateway IP with ifconfig
The difference is that FaunOS/Larch uses squashfs and aufs, which has two advantages: compression (more software can fit on the drive) and writing to the filesystem only on the shutdown, when saving changes (limiting flash drive wear). You should be able to start with a minimal system with Larch anyway.
Of course, it's up to you what solution you prefer :-)
Offline