Arch Linux

mobux

Member

Registered: 2008-10-06

Posts: 5

Can't get network running properly

Hello all,

after years of using other distros, I checked out Arch on the weekend.
I installed it parallel to my productive system and now I have a dual boot setup.
Everything went kind of well with the installation till I tried to set up my wireless networking.
The module ipw2200 is loaded correctly, also the LED of network activity is on.
I switched my router to open WLAN without any encryption, set up my default gateway (192.168.178.1) an gave
my machine the IP 192.168.178.21 ( like in my productive system).

The problem now is that I can't ping anything exept the gateway itself, neither by name nor by IP.

Any ideas?

Cheers

mobux

lmsguerr

Member

From: Loulé-Algarve-Portugal

Registered: 2008-05-20

Posts: 49

Re: Can't get network running properly

What about your DNS ip? Did you forgot it?!

---

Linux /  4.18.5-ARCH / x86_64 / Intel I5-4460s /  Intel® HD Graphics 4600  / MSI B85-G43 Gaming

mobux

Member

Registered: 2008-10-06

Posts: 5

Re: Can't get network running properly

Hi,

where do I have to put it?
But I don't think this could be the problem, cause I am also not able to
perform a ping upon an IP address.

fukawi2

Ex-Administratorino

From: .vic.au

Registered: 2007-09-28

Posts: 6,224

Website

Re: Can't get network running properly

where do I have to put it?

/etc/resolv.conf

But I don't think this could be the problem, cause I am also not able to
perform a ping upon an IP address.

Can you post the output of `route -n` and `ifconfig -a` please?

---

Are you familiar with our Forum Rules, and How To Ask Questions The Smart Way?

BlueHackers // fscanary // resticctl

mobux

Member

Registered: 2008-10-06

Posts: 5

Re: Can't get network running properly

Hi,

sorry I'm out of town for two days. I'll post the output when I'm
back home again.

mobux

mobux

Member

Registered: 2008-10-06

Posts: 5

Re: Can't get network running properly

Hello,

following the output of

ifconfig -a

eth1      Link encap:Ethernet  HWaddr 00:0E:35:B4:2F:9B 
          inet addr:192.168.178.21  Bcast:192.168.178.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:2 overruns:0 frame:0
          TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:50 (50.0 b)  TX bytes:0 (0.0 b)
          Interrupt:11 Base address:0x6000 Memory:c0210000-c0210fff

route -n

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.178.0   0.0.0.0         255.255.255.0   U     0      0        0 eth1

By the way, DNS is in /etc/resolv.conf

Any ideas?

mobux

fukawi2

Ex-Administratorino

From: .vic.au

Registered: 2007-09-28

Posts: 6,224

Website

Re: Can't get network running properly

By the way, DNS is in /etc/resolv.conf

Can you post that - everything else looks OK

---

Are you familiar with our Forum Rules, and How To Ask Questions The Smart Way?

BlueHackers // fscanary // resticctl

mobux

Member

Registered: 2008-10-06

Posts: 5

Re: Can't get network running properly

Hi there,

unfortunately I'm in the office right now not having my machine here.
As I recall from yesterday's look at /etc/resolv.conf, it looked kinka this:

nameserver 192.168.178.1

Maybe, I check what's in there on my other distro :-)
Again, I'm also not able to ping on IPs directly, therefore I don't think the problems located
with the DNS...

mobux