You are not logged in.
Pages: 1
The power went out once or twice yesterday, and in the process took out 2 arch installs (I think). Both systems dual boot arch/XP, and I can still access the internet on XP. But not in arch. I'm starting with my main box, I'd like to get it running, than I think I can figure out the other one.
All settings are as they should be, or as they should've been before whatever happened happened.
NIC: Onboard realtek something or other
module: 8139too
eth0, only connection on computer
DHCP
lspci still lists the NIC.
ifconfig only lists lo.
dhcpcd eth0 will sit there all day until ctrl-c.
/var/log/messages says something along the lines of:
"net-agent: how do i bring the interface up on this distro?"
/var/log/kernel lists nothing, nor do any of the other log files as far as I am aware.
On the startup checklist dealy, it gives a fail for starting network.
where do I start? I've already tried turning everything off (modprobe -r, rm dhcpcd.pid, etc, reload from consule), doesn't do jack, same problem.
"Ignorance is bliss, for stupid people."
"open-source is [...] programming Darwinism."
Vaughan-Nichols
Offline
ifconfig only lists lo.
this is not good.
are you sure you modprobe the right module?
arch + gentoo + initng + python = enlisy
Offline
A couple simple questions: is the nic listed in dmesg; are the nic's lights on;
At least if you can answer those you will know whether or not you need a new nic, if both are no then most likely it is bad. If the lights are off, maybe the router/switch/hub or whatever needs to be reset or the cable just needs to be moved around. I would also look at moving the nic to another pci slot, not that this is really any kind of solution, but I have had some luck with getting pci cards working by simply moving them.
Offline
Both systems dual boot arch/XP, and I can still access the internet on XP. But not in arch.
He said they work fine in XP, but not in arch, so I doubt it is a hardware problem.
Did you run fsck after you started them up?
"Be conservative in what you send; be liberal in what you accept." -- Postel's Law
"tacos" -- Cactus' Law
"t̥͍͎̪̪͗a̴̻̩͈͚ͨc̠o̩̙͈ͫͅs͙͎̙͊ ͔͇̫̜t͎̳̀a̜̞̗ͩc̗͍͚o̲̯̿s̖̣̤̙͌ ̖̜̈ț̰̫͓ạ̪͖̳c̲͎͕̰̯̃̈o͉ͅs̪ͪ ̜̻̖̜͕" -- -̖͚̫̙̓-̺̠͇ͤ̃ ̜̪̜ͯZ͔̗̭̞ͪA̝͈̙͖̩L͉̠̺͓G̙̞̦͖O̳̗͍
Offline
Must have just ignored that part for some reason, still would be interested in what dmesg has to say. Or maybe even using the hwd program.
-Steve
Offline
Did you definitely set eth0="dhcp" in rc.conf?
Do you need to run the dhcpcd daemon? I use dhcp, but just setting eth0 to dhcp in rc.conf works for me.
Offline
I have the exact same settings I had BEFORE THE STORM that worked perfect. Modules, settings and all.
I'll reboot into arch later on and check dmesg. I'm assuming the lights work fine since I can access it from windows.
I just invested in a whole wireless G setup for the rest of the house, and its wonderful getting that working. I've had all weekend, and I've got 1 out of 3 computers going, and thats just in windows.
I'm starting to hate computers
"Ignorance is bliss, for stupid people."
"open-source is [...] programming Darwinism."
Vaughan-Nichols
Offline
wow, awsome update.
Get this -
I just said screw it, its probably going bad. So I went and bought a Linksys LNE100TX. I put it in, and booted up into arch. I noticed that on 'Starting Network', it had a big fat 'PASS'.
I get flux started, and lo and behold, the internet cometh. I didn't change anything, just installed the new card.
Any ideas how that works?
Oh, and than the new linksys B+G wouldn't get recognized by my laptop (B card), so I uplinked my old B router to the G, just so I can have the laptop running wireless. Is there any advantage to having a dedicated B and G router? My network is overly complicated.
"Ignorance is bliss, for stupid people."
"open-source is [...] programming Darwinism."
Vaughan-Nichols
Offline
Pages: 1