You are not logged in.
My problem is that s2ram brings back X (and the virtual console, if I'm on one), but never the hard drive.
s2ram -f -a 1 suspends just like s2ram -f. -a 2 and 3 just make a high pitched sound.
I tried both http://wiki.archlinux.org/index.php/Suspend_to_RAM and http://wiki.archlinux.org/index.php/Pm-utils methods.
I updated my BIOS drivers but that didn't help
s2disk works perfectly.
This is a COMPAQ Presario CQ60-215DX
Here is my log of the trouble during resume:
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
sd 3:0:0:0: [sda] Starting disk
ata4.00: qc timeout (cmd 0xec)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata4.00: revalidation failed (errno=-5)
ata3.00: qc timeout (cmd 0xa1)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3.00: revalidation failed (errno=-5)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xa1)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3.00: revalidation failed (errno=-5)
ata3: limiting SATA link speed to 1.5 Gbps
ata4.00: qc timeout (cmd 0xec)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata4.00: revalidation failed (errno=-5)
ata4: limiting SATA link speed to 1.5 Gbps
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata4: SATA link up <unknown> (SStatus 103 SControl 310)
And my full log:
Linux version 2.6.30-ARCH (root@T-POWA-LX) (gcc version 4.4.1 (GCC) ) #1 SMP PREEMPT Fri Jul 31 07:30:28 CEST 2009
Command line: root=/dev/disk/by-uuid/9ae7dfa5-74b2-41e2-89bc-b344bbf47109 ro
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
Centaur CentaurHauls
...
libata version 3.00 loaded.
pata_amd 0000:00:06.0: version 0.4.1
pata_amd 0000:00:06.0: setting latency timer to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x30c0 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x30c8 irq 15
ahci 0000:00:09.0: version 3.0
ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 22
ahci 0000:00:09.0: PCI INT A -> Link[LSI0] -> GSI 22 (level, low) -> IRQ 22
ahci 0000:00:09.0: irq 25 for MSI/MSI-X
ahci 0000:00:09.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl IDE mode
ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pmp pio slum part
ahci 0000:00:09.0: setting latency timer to 64
scsi2 : ahci
scsi3 : ahci
ata3: SATA max UDMA/133 abar m8192@0xc0004000 port 0xc0004100 irq 25
ata4: SATA max UDMA/133 abar m8192@0xc0004000 port 0xc0004180 irq 25
ata2: port disabled. ignoring.
Clocksource tsc unstable (delta = 4397486409693 ns)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-8: TOSHIBA MK2555GSX, FG002C, max UDMA/100
ata4.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/100
ata3.00: ATAPI: Optiarc DVD RW AD-7580S, FH03, max UDMA/100
ata3.00: configured for UDMA/100
scsi 2:0:0:0: CD-ROM Optiarc DVD RW AD-7580S FH03 PQ: 0 ANSI: 5
scsi 3:0:0:0: Direct-Access ATA TOSHIBA MK2555GS FG00 PQ: 0 ANSI: 5
Driver 'sr' needs updating - please use bus_type methods
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
Driver 'sd' needs updating - please use bus_type methods
sd 3:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)
sd 3:0:0:0: [sda] Write Protect is off
sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 < sda5 > sda4
sd 3:0:0:0: [sda] Attached SCSI disk
EXT4-fs: INFO: recovery required on readonly filesystem.
EXT4-fs: write access will be enabled during recovery.
EXT4-fs: barriers enabled
kjournald2 starting: pid 569, dev sda2:8, commit interval 5 seconds
EXT4-fs: delayed allocation enabled
EXT4-fs: file extents enabled
EXT4-fs: mballoc enabled
EXT4-fs: sda2: orphan cleanup on readonly fs
ext4_orphan_cleanup: deleting unreferenced inode 148384
ext4_orphan_cleanup: deleting unreferenced inode 147907
ext4_orphan_cleanup: deleting unreferenced inode 147903
EXT4-fs: sda2: 3 orphan inodes deleted
EXT4-fs: recovery complete.
EXT4-fs: mounted filesystem sda2 with ordered data mode
rtc_cmos 00:06: RTC can wake from S4
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
udev: starting version 141
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
ACPI: AC Adapter [ADP1] (on-line)
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 21
forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
forcedeth 0000:00:0a.0: setting latency timer to 64
sr 2:0:0:0: Attached scsi generic sg0 type 5
sd 3:0:0:0: Attached scsi generic sg1 type 0
usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
cfg80211: Calling CRDA to update world regulatory domain
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
ACPI: Power Button [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3
ACPI: Lid Switch [LID0]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4
ACPI: Sleep Button [SLPB]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5
ACPI: Power Button [PWRB]
processor ACPI_CPU:00: registered as cooling_device0
processor ACPI_CPU:01: registered as cooling_device1
forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1f:16:74:cb:72
forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt lnktim msi desc-v3
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 17
ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:02.1: setting latency timer to 64
ehci_hcd 0000:00:02.1: EHCI Host Controller
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
ehci_hcd 0000:00:02.1: irq 17, io mem 0xc0007000
ACPI: WMI: Mapper loaded
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 17
ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 17, io mem 0xc0006000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [Z011] enabled at IRQ 16
ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z011] -> GSI 16 (level, low) -> IRQ 16
ehci_hcd 0000:00:04.1: setting latency timer to 64
ehci_hcd 0000:00:04.1: EHCI Host Controller
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 3
ehci_hcd 0000:00:04.1: debug port 1
ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
ehci_hcd 0000:00:04.1: irq 16, io mem 0xc0007400
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [Z010] enabled at IRQ 16
ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z010] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:04.0: setting latency timer to 64
ohci_hcd 0000:00:04.0: OHCI Host Controller
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:04.0: irq 16, io mem 0xc0008000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 4 ports detected
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [TZS0] (68 C)
ACPI: Battery Slot [BAT0] (battery present)
thermal LNXTHERM:02: registered as thermal_zone1
ACPI: Thermal Zone [TZS1] (68 C)
usb 1-1: new high speed USB device using ehci_hcd and address 2
nvidia: module license 'NVIDIA' taints kernel.
Disabling lock debugging due to kernel taint
usb 1-1: configuration #1 chosen from 1 choice
Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1a0b1, caps: 0xd04711/0xa00000
acpi device:13: registered as cooling_device2
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:10/device:11/input/input6
ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
usb 3-4: new high speed USB device using ehci_hcd and address 2
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input7
ath5k 0000:07:00.0: PCI INT A -> Link[Z012] -> GSI 23 (level, low) -> IRQ 23
ath5k 0000:07:00.0: setting latency timer to 64
ath5k 0000:07:00.0: registered as 'phy0'
usb 3-4: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 20
nvidia 0000:02:00.0: PCI INT A -> Link[LGPU] -> GSI 20 (level, low) -> IRQ 20
nvidia 0000:02:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 185.18.31 Tue Jul 28 17:52:27 PDT 2009
EXT4 FS on sda2, internal journal on sda2:8
Adding 3148700k swap on /dev/sda5. Priority:-1 extents:1 across:3148700k
scsi 4:0:0:0: Direct-Access Generic- Multi-Card 1.00 PQ: 0 ANSI: 0 CCS
sd 4:0:0:0: Attached scsi generic sg2 type 0
usb-storage: device scan complete
sd 4:0:0:0: [sdb] Attached SCSI removable disk
scsi 5:0:0:0: Direct-Access USB Driver 0.00 PQ: 0 ANSI: 0 CCS
sd 5:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
sd 5:0:0:0: [sdc] 7827456 512-byte hardware sectors: (4.00 GB/3.73 GiB)
sd 5:0:0:0: [sdc] Write Protect is off
sd 5:0:0:0: [sdc] Mode Sense: 23 00 00 00
sd 5:0:0:0: [sdc] Assuming drive cache: write through
sd 5:0:0:0: [sdc] Assuming drive cache: write through
sdc:
sd 5:0:0:0: [sdc] Attached SCSI removable disk
forcedeth 0000:00:0a.0: irq 26 for MSI/MSI-X
eth0: no link during initialization.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ADDRCONF(NETDEV_UP): eth0: link is not ready
PM: Syncing filesystems ... done.
Freezing user space processes ... (elapsed 0.00 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.
Suspending console(s) (use no_console_suspend to debug)
sd 3:0:0:0: [sda] Synchronizing SCSI cache
sd 3:0:0:0: [sda] Stopping disk
ath5k 0000:07:00.0: PCI INT A disabled
forcedeth 0000:00:0a.0: wake-up capability disabled by ACPI
forcedeth 0000:00:0a.0: PME# disabled
forcedeth 0000:00:0a.0: PCI INT A disabled
HDA Intel 0000:00:07.0: PCI INT A disabled
ata2: port disabled. ignoring.
ehci_hcd 0000:00:04.1: PCI INT B disabled
ehci_hcd 0000:00:04.1: PME# disabled
ohci_hcd 0000:00:04.0: PCI INT A disabled
ohci_hcd 0000:00:04.0: PME# disabled
ehci_hcd 0000:00:02.1: PCI INT B disabled
ehci_hcd 0000:00:02.1: PME# disabled
ohci_hcd 0000:00:02.0: PCI INT A disabled
ohci_hcd 0000:00:02.0: PME# disabled
ACPI: Preparing to enter system sleep state S3
Disabling non-boot CPUs ...
CPU 1 is now offline
SMP alternatives: switching to UP code
CPU0 attaching NULL sched-domain.
CPU1 attaching NULL sched-domain.
CPU0 attaching NULL sched-domain.
CPU1 is down
Extended CMOS year: 2000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
Back to C!
Extended CMOS year: 2000
Enabling non-boot CPUs ...
SMP alternatives: switching to SMP code
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 4001.76 BogoMIPS (lpj=6666816)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: AMD Athlon Dual-Core QL-62 stepping 01
CPU0 attaching NULL sched-domain.
Switched to high resolution mode on CPU 1
CPU0 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 0 1
CPU1 attaching sched-domain:
domain 0: span 0-1 level MC
groups: 1 0
CPU1 is up
ACPI: Waking up from system sleep state S3
ohci_hcd 0000:00:02.0: restoring config space at offset 0x1 (was 0xb00007, writing 0xb00003)
ehci_hcd 0000:00:02.1: restoring config space at offset 0x1 (was 0xb00006, writing 0xb00002)
ohci_hcd 0000:00:04.0: restoring config space at offset 0x1 (was 0xb00007, writing 0xb00003)
ehci_hcd 0000:00:04.1: restoring config space at offset 0x1 (was 0xb00006, writing 0xb00002)
pata_amd 0000:00:06.0: restoring config space at offset 0x1 (was 0xb00005, writing 0xb80005)
HDA Intel 0000:00:07.0: restoring config space at offset 0xf (was 0x5020100, writing 0x502010a)
HDA Intel 0000:00:07.0: restoring config space at offset 0x4 (was 0x0, writing 0xc0000000)
HDA Intel 0000:00:07.0: restoring config space at offset 0x1 (was 0xb00000, writing 0xb00002)
ahci 0000:00:09.0: restoring config space at offset 0x1 (was 0xb00007, writing 0xb00407)
pcieport-driver 0000:00:14.0: restoring config space at offset 0x7 (was 0x1f1, writing 0x200001f1)
pcieport-driver 0000:00:14.0: restoring config space at offset 0x1 (was 0x100107, writing 0x1005
nvidia 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)
nvidia 0000:02:00.0: restoring config space at offset 0x9 (was 0x1, writing 0x4001)
nvidia 0000:02:00.0: restoring config space at offset 0x7 (was 0xc, writing 0xc400000c)
nvidia 0000:02:00.0: restoring config space at offset 0x5 (was 0xc, writing 0xd000000c)
ath5k 0000:07:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)
nForce2_smbus 0000:00:01.1: PME# disabled
ohci_hcd 0000:00:02.0: PME# disabled
ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 17 (level, low) -> IRQ 17
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: PME# disabled
ehci_hcd 0000:00:02.1: PME# disabled
ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 17 (level, low) -> IRQ 17
ehci_hcd 0000:00:02.1: setting latency timer to 64
ehci_hcd 0000:00:02.1: PME# disabled
usb usb1: root hub lost power or was reset
ehci_hcd 0000:00:02.1: debug port 1
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
ohci_hcd 0000:00:04.0: PME# disabled
ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z010] -> GSI 16 (level, low) -> IRQ 16
ohci_hcd 0000:00:04.0: setting latency timer to 64
ohci_hcd 0000:00:04.0: PME# disabled
ehci_hcd 0000:00:04.1: PME# disabled
ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z011] -> GSI 16 (level, low) -> IRQ 16
ehci_hcd 0000:00:04.1: setting latency timer to 64
ehci_hcd 0000:00:04.1: PME# disabled
usb usb3: root hub lost power or was reset
ehci_hcd 0000:00:04.1: debug port 1
ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
pata_amd 0000:00:06.0: restoring config space at offset 0x1 (was 0xb00005, writing 0xb80005)
pata_amd 0000:00:06.0: setting latency timer to 64
ata2: port disabled. ignoring.
HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 19 (level, low) -> IRQ 19
HDA Intel 0000:00:07.0: setting latency timer to 64
pci 0000:00:08.0: setting latency timer to 64
ahci 0000:00:09.0: setting latency timer to 64
forcedeth 0000:00:0a.0: wake-up capability disabled by ACPI
forcedeth 0000:00:0a.0: PME# disabled
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
forcedeth 0000:00:0a.0: irq 26 for MSI/MSI-X
eth0: no link during initialization.
pci 0000:00:0b.0: setting latency timer to 64
ath5k 0000:07:00.0: PCI INT A -> Link[Z012] -> GSI 23 (level, low) -> IRQ 23
sd 3:0:0:0: [sda] Starting disk
ata4.00: qc timeout (cmd 0xec)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata4.00: revalidation failed (errno=-5)
ata3.00: qc timeout (cmd 0xa1)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3.00: revalidation failed (errno=-5)
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: qc timeout (cmd 0xa1)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3.00: revalidation failed (errno=-5)
ata3: limiting SATA link speed to 1.5 Gbps
ata4.00: qc timeout (cmd 0xec)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata4.00: revalidation failed (errno=-5)
ata4: limiting SATA link speed to 1.5 Gbps
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata4: SATA link up <unknown> (SStatus 103 SControl 310)
ata4.00: qc timeout (cmd 0xec)
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata4.00: revalidation failed (errno=-5)
ata4.00: disabled
ata3.00: qc timeout (cmd 0xa1)
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)
ata3.00: revalidation failed (errno=-5)
ata3.00: disabled
sd 3:0:0:0: [sda] START_STOP FAILED
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 134590273
Buffer I/O error on device sda2, logical block 1094141
lost page write due to I/O error on sda2
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 135807281
Buffer I/O error on device sda2, logical block 1246267
lost page write due to I/O error on sda2
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 135815833
Buffer I/O error on device sda2, logical block 1247336
lost page write due to I/O error on sda2
JBD2: Detected IO errors while flushing file data on sda2:8
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 155463993
Aborting journal on device sda2:8.
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 155459417
Buffer I/O error on device sda2, logical block 3702784
lost page write due to I/O error on sda2
JBD2: I/O error detected when updating journal superblock for sda2:8.
PM: Device 3:0:0:0 failed to resume: error 262144
usb 1-1: reset high speed USB device using ehci_hcd and address 2
usb 3-4: reset high speed USB device using ehci_hcd and address 2
Restarting tasks ... <2>ext4_abort called.
EXT4-fs error (device sda2): ext4_journal_start_sb: Detected aborted journal
Remounting filesystem read-only
ext4_da_writepages: jbd2_start: 1024 pages, ino 131086; err -30
Pid: 20, comm: pdflush Tainted: P 2.6.30-ARCH #1
Call Trace:
[<ffffffffa00d738d>] ? ext4_da_writepages+0x47d/0x4b0 [ext4]
[<ffffffff8026c6a4>] ? bit_waitqueue+0x24/0xe0
[<ffffffff802c8332>] ? do_writepages+0x32/0x60
[<ffffffff80321b7a>] ? __writeback_single_inode+0xba/0x490
[<ffffffff802406e6>] ? dequeue_task_fair+0x56/0x1d0
[<ffffffff8020a95c>] ? __switch_to+0xdc/0x3b0
[<ffffffff803223b3>] ? generic_sync_sb_inodes+0x193/0x530
[<ffffffff803229c5>] ? writeback_inodes+0x65/0x120
[<ffffffff802c85a6>] ? wb_kupdate+0xc6/0x160
[<ffffffff802c995b>] ? pdflush+0x16b/0x2a0
[<ffffffff802c84e0>] ? wb_kupdate+0x0/0x160
[<ffffffff802c97f0>] ? pdflush+0x0/0x2a0
[<ffffffff802c97f0>] ? pdflush+0x0/0x2a0
[<ffffffff8026c204>] ? kthread+0x64/0xc0
[<ffffffff8024af20>] ? schedule_tail+0x30/0x80
[<ffffffff8020d4fa>] ? child_rip+0xa/0x20
[<ffffffff8026c1a0>] ? kthread+0x0/0xc0
[<ffffffff8020d4f0>] ? child_rip+0x0/0x20
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126637417
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126637417
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126637417
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126637417
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126637417
done.
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 130097993
EXT4-fs error (device sda2): ext4_find_entry: reading directory #139292 offset 0
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126637417
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126004889
EXT4-fs error (device sda2): ext4_find_entry: reading directory #98457 offset 0
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126004889
EXT4-fs error (device sda2): ext4_find_entry: reading directory #98457 offset 0
ANY help would be much appreciated.
Last edited by Cappy (2009-08-10 08:19:09)
Offline
Nevermind .. *sigh* ... pci=msi on the kernel fixed it .. going to go cut myself now ...
Offline