You are not logged in.

#1 2009-08-10 08:02:00

Cappy
Member
Registered: 2008-10-13
Posts: 20

[Solved] Laptop Suspend puts Hard Drive into Read-Only

My problem is that s2ram brings back X (and the virtual console, if I'm on one), but never the hard drive.

s2ram -f -a 1 suspends just like s2ram -f. -a 2 and 3 just make a high pitched sound.
I tried both http://wiki.archlinux.org/index.php/Suspend_to_RAM and http://wiki.archlinux.org/index.php/Pm-utils methods.
I updated my BIOS drivers but that didn't help
s2disk works perfectly.
This is a COMPAQ Presario CQ60-215DX

Here is my log of the trouble during resume:

ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)                                          
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)      
sd 3:0:0:0: [sda] Starting disk                                                                 
ata4.00: qc timeout (cmd 0xec)                                                                  
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)                                           
ata4.00: revalidation failed (errno=-5)                                                         
ata3.00: qc timeout (cmd 0xa1)                                                                  
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)                                           
ata3.00: revalidation failed (errno=-5)                                                         
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)                                          
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)                                          
ata3.00: qc timeout (cmd 0xa1)                                                                  
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)                                           
ata3.00: revalidation failed (errno=-5)                                                         
ata3: limiting SATA link speed to 1.5 Gbps                                                      
ata4.00: qc timeout (cmd 0xec)                                                                  
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)                                           
ata4.00: revalidation failed (errno=-5)                                                         
ata4: limiting SATA link speed to 1.5 Gbps                                                      
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)                                          
ata4: SATA link up <unknown> (SStatus 103 SControl 310)

And my full log:

Linux version 2.6.30-ARCH (root@T-POWA-LX) (gcc version 4.4.1 (GCC) ) #1 SMP PREEMPT Fri Jul 31 07:30:28 CEST 2009                                                                              
Command line: root=/dev/disk/by-uuid/9ae7dfa5-74b2-41e2-89bc-b344bbf47109 ro                    
KERNEL supported cpus:                                                                          
  Intel GenuineIntel                                                                            
  AMD AuthenticAMD                                                                              
  Centaur CentaurHauls                                                                          

...

libata version 3.00 loaded.                                                                     
pata_amd 0000:00:06.0: version 0.4.1                                                            
pata_amd 0000:00:06.0: setting latency timer to 64                                              
scsi0 : pata_amd                                                                                
scsi1 : pata_amd                                                                                
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x30c0 irq 14                                 
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x30c8 irq 15                                 
ahci 0000:00:09.0: version 3.0                                                                  
ACPI: PCI Interrupt Link [LSI0] enabled at IRQ 22                                               
ahci 0000:00:09.0: PCI INT A -> Link[LSI0] -> GSI 22 (level, low) -> IRQ 22                     
ahci 0000:00:09.0: irq 25 for MSI/MSI-X                                                         
ahci 0000:00:09.0: AHCI 0001.0200 32 slots 2 ports 3 Gbps 0x3 impl IDE mode                     
ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pmp pio slum part                              
ahci 0000:00:09.0: setting latency timer to 64                                                  
scsi2 : ahci                                                                                    
scsi3 : ahci                                                                                    
ata3: SATA max UDMA/133 abar m8192@0xc0004000 port 0xc0004100 irq 25                            
ata4: SATA max UDMA/133 abar m8192@0xc0004000 port 0xc0004180 irq 25                            
ata2: port disabled. ignoring.                                                                  
Clocksource tsc unstable (delta = 4397486409693 ns)                                             
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)                                          
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)                                          
ata4.00: ATA-8: TOSHIBA MK2555GSX, FG002C, max UDMA/100                                         
ata4.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32)                                   
ata4.00: configured for UDMA/100                                                                
ata3.00: ATAPI: Optiarc DVD RW AD-7580S, FH03, max UDMA/100                                     
ata3.00: configured for UDMA/100                                                                
scsi 2:0:0:0: CD-ROM            Optiarc  DVD RW AD-7580S  FH03 PQ: 0 ANSI: 5                    
scsi 3:0:0:0: Direct-Access     ATA      TOSHIBA MK2555GS FG00 PQ: 0 ANSI: 5                    
Driver 'sr' needs updating - please use bus_type methods                                        
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray                           
Uniform CD-ROM driver Revision: 3.20                                                            
sr 2:0:0:0: Attached scsi CD-ROM sr0                                                            
Driver 'sd' needs updating - please use bus_type methods                                        
sd 3:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB)                         
sd 3:0:0:0: [sda] Write Protect is off                                                          
sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00                                                       
sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA         
 sda: sda1 sda2 sda3 < sda5 > sda4                                                              
sd 3:0:0:0: [sda] Attached SCSI disk                                                            
EXT4-fs: INFO: recovery required on readonly filesystem.                                        
EXT4-fs: write access will be enabled during recovery.                                          
EXT4-fs: barriers enabled                                                                       
kjournald2 starting: pid 569, dev sda2:8, commit interval 5 seconds                             
EXT4-fs: delayed allocation enabled                                                             
EXT4-fs: file extents enabled                                                                   
EXT4-fs: mballoc enabled                                                                        
EXT4-fs: sda2: orphan cleanup on readonly fs                                                    
ext4_orphan_cleanup: deleting unreferenced inode 148384                                         
ext4_orphan_cleanup: deleting unreferenced inode 147907                                         
ext4_orphan_cleanup: deleting unreferenced inode 147903                                         
EXT4-fs: sda2: 3 orphan inodes deleted                                                          
EXT4-fs: recovery complete.                                                                     
EXT4-fs: mounted filesystem sda2 with ordered data mode                                         
rtc_cmos 00:06: RTC can wake from S4                                                            
rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0                                           
rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs                                    
udev: starting version 141                                                                      
pci_hotplug: PCI Hot Plug PCI Core version: 0.5                                                 
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4                                    
usbcore: registered new interface driver usbfs                                                  
usbcore: registered new interface driver hub                                                    
ACPI: AC Adapter [ADP1] (on-line)                                                               
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.                             
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 21                                               
forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21                
forcedeth 0000:00:0a.0: setting latency timer to 64                                             
sr 2:0:0:0: Attached scsi generic sg0 type 5                                                    
sd 3:0:0:0: Attached scsi generic sg1 type 0                                                    
usbcore: registered new device driver usb                                                       
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver                                      
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver                                          
cfg80211: Calling CRDA to update world regulatory domain                                        
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2                            
ACPI: Power Button [PWRF]                                                                       
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input3                     
ACPI: Lid Switch [LID0]                                                                         
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input4                   
ACPI: Sleep Button [SLPB]                                                                       
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input5                   
ACPI: Power Button [PWRB]                                                                       
processor ACPI_CPU:00: registered as cooling_device0                                            
processor ACPI_CPU:01: registered as cooling_device1                                            
forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 1, addr 00:1f:16:74:cb:72                  
forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt lnktim msi desc-v3                             
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 17                                               
ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 17 (level, low) -> IRQ 17                 
ehci_hcd 0000:00:02.1: setting latency timer to 64                                              
ehci_hcd 0000:00:02.1: EHCI Host Controller                                                     
ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1                            
ehci_hcd 0000:00:02.1: debug port 1                                                             
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported                                   
ehci_hcd 0000:00:02.1: irq 17, io mem 0xc0007000                                                
ACPI: WMI: Mapper loaded                                                                        
ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00                                               
usb usb1: configuration #1 chosen from 1 choice                                                 
hub 1-0:1.0: USB hub found                                                                      
hub 1-0:1.0: 3 ports detected                                                                   
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x3040                                              
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x3000                                              
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 17                                               
ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 17 (level, low) -> IRQ 17                 
ohci_hcd 0000:00:02.0: setting latency timer to 64                                              
ohci_hcd 0000:00:02.0: OHCI Host Controller                                                     
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2                            
ohci_hcd 0000:00:02.0: irq 17, io mem 0xc0006000                                                
usb usb2: configuration #1 chosen from 1 choice                                                 
hub 2-0:1.0: USB hub found                                                                      
hub 2-0:1.0: 3 ports detected                                                                   
ACPI: PCI Interrupt Link [Z011] enabled at IRQ 16                                               
ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z011] -> GSI 16 (level, low) -> IRQ 16                 
ehci_hcd 0000:00:04.1: setting latency timer to 64                                              
ehci_hcd 0000:00:04.1: EHCI Host Controller                                                     
ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 3                            
ehci_hcd 0000:00:04.1: debug port 1                                                             
ehci_hcd 0000:00:04.1: cache line size of 64 is not supported                                   
ehci_hcd 0000:00:04.1: irq 16, io mem 0xc0007400                                                
ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00                                               
usb usb3: configuration #1 chosen from 1 choice                                                 
hub 3-0:1.0: USB hub found                                                                      
hub 3-0:1.0: 4 ports detected                                                                   
ACPI: PCI Interrupt Link [Z010] enabled at IRQ 16                                               
ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z010] -> GSI 16 (level, low) -> IRQ 16                 
ohci_hcd 0000:00:04.0: setting latency timer to 64                                              
ohci_hcd 0000:00:04.0: OHCI Host Controller                                                     
ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4                            
ohci_hcd 0000:00:04.0: irq 16, io mem 0xc0008000                                                
usb usb4: configuration #1 chosen from 1 choice                                                 
hub 4-0:1.0: USB hub found                                                                      
hub 4-0:1.0: 4 ports detected                                                                   
thermal LNXTHERM:01: registered as thermal_zone0                                                
ACPI: Thermal Zone [TZS0] (68 C)                                                                
ACPI: Battery Slot [BAT0] (battery present)                                                     
thermal LNXTHERM:02: registered as thermal_zone1                                                
ACPI: Thermal Zone [TZS1] (68 C)                                                                
usb 1-1: new high speed USB device using ehci_hcd and address 2                                 
nvidia: module license 'NVIDIA' taints kernel.                                                  
Disabling lock debugging due to kernel taint                                                    
usb 1-1: configuration #1 chosen from 1 choice                                                  
Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1a0b1, caps: 0xd04711/0xa00000                     
acpi device:13: registered as cooling_device2                                                   
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:10/device:11/input/input6  
ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)                                   
usb 3-4: new high speed USB device using ehci_hcd and address 2                                 
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio2/input/input7                
ath5k 0000:07:00.0: PCI INT A -> Link[Z012] -> GSI 23 (level, low) -> IRQ 23                    
ath5k 0000:07:00.0: setting latency timer to 64                                                 
ath5k 0000:07:00.0: registered as 'phy0'                                                        
usb 3-4: configuration #1 chosen from 1 choice                                                  
ACPI: PCI Interrupt Link [LGPU] enabled at IRQ 20                                               
nvidia 0000:02:00.0: PCI INT A -> Link[LGPU] -> GSI 20 (level, low) -> IRQ 20                   
nvidia 0000:02:00.0: setting latency timer to 64                                                
NVRM: loading NVIDIA UNIX x86_64 Kernel Module  185.18.31  Tue Jul 28 17:52:27 PDT 2009         


EXT4 FS on sda2, internal journal on sda2:8                                                     
Adding 3148700k swap on /dev/sda5.  Priority:-1 extents:1 across:3148700k                       
scsi 4:0:0:0: Direct-Access     Generic- Multi-Card       1.00 PQ: 0 ANSI: 0 CCS                
sd 4:0:0:0: Attached scsi generic sg2 type 0                                                    
usb-storage: device scan complete                                                               
sd 4:0:0:0: [sdb] Attached SCSI removable disk                                                  
scsi 5:0:0:0: Direct-Access     USB      Driver           0.00 PQ: 0 ANSI: 0 CCS                
sd 5:0:0:0: Attached scsi generic sg3 type 0                                                    
usb-storage: device scan complete                                                               
sd 5:0:0:0: [sdc] 7827456 512-byte hardware sectors: (4.00 GB/3.73 GiB)                         
sd 5:0:0:0: [sdc] Write Protect is off                                                          
sd 5:0:0:0: [sdc] Mode Sense: 23 00 00 00                                                       
sd 5:0:0:0: [sdc] Assuming drive cache: write through                                           
sd 5:0:0:0: [sdc] Assuming drive cache: write through                                           
 sdc:                                                                                           
sd 5:0:0:0: [sdc] Attached SCSI removable disk                                                  
forcedeth 0000:00:0a.0: irq 26 for MSI/MSI-X                                                    
eth0: no link during initialization.                                                            
NET: Registered protocol family 10                                                              
lo: Disabled Privacy Extensions                                                                 
ADDRCONF(NETDEV_UP): eth0: link is not ready                                                    
PM: Syncing filesystems ... done.                                                               
Freezing user space processes ... (elapsed 0.00 seconds) done.                                  
Freezing remaining freezable tasks ... (elapsed 0.00 seconds) done.                             
Suspending console(s) (use no_console_suspend to debug)                                         
sd 3:0:0:0: [sda] Synchronizing SCSI cache                                                      
sd 3:0:0:0: [sda] Stopping disk                                                                 
ath5k 0000:07:00.0: PCI INT A disabled                                                          
forcedeth 0000:00:0a.0: wake-up capability disabled by ACPI                                     
forcedeth 0000:00:0a.0: PME# disabled                                                           
forcedeth 0000:00:0a.0: PCI INT A disabled                                                      
HDA Intel 0000:00:07.0: PCI INT A disabled                                                      
ata2: port disabled. ignoring.                                                                  
ehci_hcd 0000:00:04.1: PCI INT B disabled                                                       
ehci_hcd 0000:00:04.1: PME# disabled                                                            
ohci_hcd 0000:00:04.0: PCI INT A disabled                                                       
ohci_hcd 0000:00:04.0: PME# disabled                                                            
ehci_hcd 0000:00:02.1: PCI INT B disabled                                                       
ehci_hcd 0000:00:02.1: PME# disabled                                                            
ohci_hcd 0000:00:02.0: PCI INT A disabled                                                       
ohci_hcd 0000:00:02.0: PME# disabled                                                            
ACPI: Preparing to enter system sleep state S3                                                  
Disabling non-boot CPUs ...                                                                     
CPU 1 is now offline                                                                            
SMP alternatives: switching to UP code                                                          
CPU0 attaching NULL sched-domain.                                                               
CPU1 attaching NULL sched-domain.                                                               
CPU0 attaching NULL sched-domain.                                                               
CPU1 is down                                                                                    
Extended CMOS year: 2000                                                                        
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106                                
Back to C!                                                                                      
Extended CMOS year: 2000                                                                        
Enabling non-boot CPUs ...                                                                      
SMP alternatives: switching to SMP code                                                         
Booting processor 1 APIC 0x1 ip 0x6000                                                          
Initializing CPU#1                                                                              
Calibrating delay using timer specific routine.. 4001.76 BogoMIPS (lpj=6666816)                 
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)                               
CPU: L2 Cache: 512K (64 bytes/line)                                                             
CPU: Physical Processor ID: 0                                                                   
CPU: Processor Core ID: 1                                                                       
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106                                
CPU1: AMD Athlon Dual-Core QL-62 stepping 01                                                    
CPU0 attaching NULL sched-domain.                                                               
Switched to high resolution mode on CPU 1                                                       
CPU0 attaching sched-domain:                                                                    
 domain 0: span 0-1 level MC                                                                    
  groups: 0 1                                                                                   
CPU1 attaching sched-domain:                                                                    
 domain 0: span 0-1 level MC                                                                    
  groups: 1 0                                                                                   
CPU1 is up                                                                                      
ACPI: Waking up from system sleep state S3                                                      
ohci_hcd 0000:00:02.0: restoring config space at offset 0x1 (was 0xb00007, writing 0xb00003)    
ehci_hcd 0000:00:02.1: restoring config space at offset 0x1 (was 0xb00006, writing 0xb00002)    
ohci_hcd 0000:00:04.0: restoring config space at offset 0x1 (was 0xb00007, writing 0xb00003)    
ehci_hcd 0000:00:04.1: restoring config space at offset 0x1 (was 0xb00006, writing 0xb00002)    
pata_amd 0000:00:06.0: restoring config space at offset 0x1 (was 0xb00005, writing 0xb80005)    
HDA Intel 0000:00:07.0: restoring config space at offset 0xf (was 0x5020100, writing 0x502010a) 
HDA Intel 0000:00:07.0: restoring config space at offset 0x4 (was 0x0, writing 0xc0000000)      
HDA Intel 0000:00:07.0: restoring config space at offset 0x1 (was 0xb00000, writing 0xb00002)   
ahci 0000:00:09.0: restoring config space at offset 0x1 (was 0xb00007, writing 0xb00407)        
pcieport-driver 0000:00:14.0: restoring config space at offset 0x7 (was 0x1f1, writing 0x200001f1)                    
pcieport-driver 0000:00:14.0: restoring config space at offset 0x1 (was 0x100107, writing 0x1005
nvidia 0000:02:00.0: restoring config space at offset 0xf (was 0x100, writing 0x10a)            
nvidia 0000:02:00.0: restoring config space at offset 0x9 (was 0x1, writing 0x4001)             
nvidia 0000:02:00.0: restoring config space at offset 0x7 (was 0xc, writing 0xc400000c)         
nvidia 0000:02:00.0: restoring config space at offset 0x5 (was 0xc, writing 0xd000000c)         
ath5k 0000:07:00.0: restoring config space at offset 0x3 (was 0x0, writing 0x10)                
nForce2_smbus 0000:00:01.1: PME# disabled                                                       
ohci_hcd 0000:00:02.0: PME# disabled                                                            
ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 17 (level, low) -> IRQ 17                 
ohci_hcd 0000:00:02.0: setting latency timer to 64                                              
ohci_hcd 0000:00:02.0: PME# disabled                                                            
ehci_hcd 0000:00:02.1: PME# disabled                                                            
ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUS2] -> GSI 17 (level, low) -> IRQ 17                 
ehci_hcd 0000:00:02.1: setting latency timer to 64                                              
ehci_hcd 0000:00:02.1: PME# disabled                                                            
usb usb1: root hub lost power or was reset                                                      
ehci_hcd 0000:00:02.1: debug port 1                                                             
ehci_hcd 0000:00:02.1: cache line size of 64 is not supported                                   
ohci_hcd 0000:00:04.0: PME# disabled                                                            
ohci_hcd 0000:00:04.0: PCI INT A -> Link[Z010] -> GSI 16 (level, low) -> IRQ 16                 
ohci_hcd 0000:00:04.0: setting latency timer to 64                                              
ohci_hcd 0000:00:04.0: PME# disabled                                                            
ehci_hcd 0000:00:04.1: PME# disabled                                                            
ehci_hcd 0000:00:04.1: PCI INT B -> Link[Z011] -> GSI 16 (level, low) -> IRQ 16                 
ehci_hcd 0000:00:04.1: setting latency timer to 64                                              
ehci_hcd 0000:00:04.1: PME# disabled                                                            
usb usb3: root hub lost power or was reset                                                      
ehci_hcd 0000:00:04.1: debug port 1                                                             
ehci_hcd 0000:00:04.1: cache line size of 64 is not supported                                   
pata_amd 0000:00:06.0: restoring config space at offset 0x1 (was 0xb00005, writing 0xb80005)    
pata_amd 0000:00:06.0: setting latency timer to 64                                              
ata2: port disabled. ignoring.                                                                  
HDA Intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 19 (level, low) -> IRQ 19                
HDA Intel 0000:00:07.0: setting latency timer to 64                                             
pci 0000:00:08.0: setting latency timer to 64                                                   
ahci 0000:00:09.0: setting latency timer to 64                                                  
forcedeth 0000:00:0a.0: wake-up capability disabled by ACPI                                     
forcedeth 0000:00:0a.0: PME# disabled                                                           
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)                                          
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)                                          
forcedeth 0000:00:0a.0: irq 26 for MSI/MSI-X                                                    
eth0: no link during initialization.                                                            
pci 0000:00:0b.0: setting latency timer to 64                                                   
ath5k 0000:07:00.0: PCI INT A -> Link[Z012] -> GSI 23 (level, low) -> IRQ 23                    
sd 3:0:0:0: [sda] Starting disk                                                                 
ata4.00: qc timeout (cmd 0xec)                                                                  
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)                                           
ata4.00: revalidation failed (errno=-5)                                                         
ata3.00: qc timeout (cmd 0xa1)                                                                  
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)                                           
ata3.00: revalidation failed (errno=-5)                                                         
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)                                          
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)                                          
ata3.00: qc timeout (cmd 0xa1)                                                                  
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)                                           
ata3.00: revalidation failed (errno=-5)                                                         
ata3: limiting SATA link speed to 1.5 Gbps                                                      
ata4.00: qc timeout (cmd 0xec)                                                                  
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)                                           
ata4.00: revalidation failed (errno=-5)                                                         
ata4: limiting SATA link speed to 1.5 Gbps                                                      
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)                                          
ata4: SATA link up <unknown> (SStatus 103 SControl 310)                                         
ata4.00: qc timeout (cmd 0xec)                                                                  
ata4.00: failed to IDENTIFY (I/O error, err_mask=0x4)                                           
ata4.00: revalidation failed (errno=-5)                                                         
ata4.00: disabled                                                                               
ata3.00: qc timeout (cmd 0xa1)                                                                  
ata3.00: failed to IDENTIFY (I/O error, err_mask=0x4)                                           
ata3.00: revalidation failed (errno=-5)                                                         
ata3.00: disabled                                                                               
sd 3:0:0:0: [sda] START_STOP FAILED                                                             
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00                                         
sd 3:0:0:0: [sda] Unhandled error code                                                          
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00                                         
end_request: I/O error, dev sda, sector 134590273                                               
Buffer I/O error on device sda2, logical block 1094141                                          
lost page write due to I/O error on sda2                                                        
sd 3:0:0:0: [sda] Unhandled error code                                                          
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00                                         
end_request: I/O error, dev sda, sector 135807281                                               
Buffer I/O error on device sda2, logical block 1246267                                          
lost page write due to I/O error on sda2                                                        
sd 3:0:0:0: [sda] Unhandled error code                                                          
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00                                         
end_request: I/O error, dev sda, sector 135815833                                               
Buffer I/O error on device sda2, logical block 1247336                                          
lost page write due to I/O error on sda2                                                        
JBD2: Detected IO errors while flushing file data on sda2:8                                     
sd 3:0:0:0: [sda] Unhandled error code                                                          
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00                                         
end_request: I/O error, dev sda, sector 155463993                                               
Aborting journal on device sda2:8.                                                              
sd 3:0:0:0: [sda] Unhandled error code                                                          
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00                                         
end_request: I/O error, dev sda, sector 155459417                                               
Buffer I/O error on device sda2, logical block 3702784                                          
lost page write due to I/O error on sda2                                                        
JBD2: I/O error detected when updating journal superblock for sda2:8.                           
PM: Device 3:0:0:0 failed to resume: error 262144                                               
usb 1-1: reset high speed USB device using ehci_hcd and address 2                               
usb 3-4: reset high speed USB device using ehci_hcd and address 2                               
Restarting tasks ... <2>ext4_abort called.                                                      
EXT4-fs error (device sda2): ext4_journal_start_sb: Detected aborted journal                    
Remounting filesystem read-only                                                                 
ext4_da_writepages: jbd2_start: 1024 pages, ino 131086; err -30                                 
Pid: 20, comm: pdflush Tainted: P           2.6.30-ARCH #1                                      
Call Trace:                                                                                     
 [<ffffffffa00d738d>] ? ext4_da_writepages+0x47d/0x4b0 [ext4]                                   
 [<ffffffff8026c6a4>] ? bit_waitqueue+0x24/0xe0                                                 
 [<ffffffff802c8332>] ? do_writepages+0x32/0x60                                                 
 [<ffffffff80321b7a>] ? __writeback_single_inode+0xba/0x490                                     
 [<ffffffff802406e6>] ? dequeue_task_fair+0x56/0x1d0                                            
 [<ffffffff8020a95c>] ? __switch_to+0xdc/0x3b0                                                  
 [<ffffffff803223b3>] ? generic_sync_sb_inodes+0x193/0x530                                      
 [<ffffffff803229c5>] ? writeback_inodes+0x65/0x120                                             
 [<ffffffff802c85a6>] ? wb_kupdate+0xc6/0x160                                                   
 [<ffffffff802c995b>] ? pdflush+0x16b/0x2a0                                                     
 [<ffffffff802c84e0>] ? wb_kupdate+0x0/0x160                                                    
 [<ffffffff802c97f0>] ? pdflush+0x0/0x2a0                                                       
 [<ffffffff802c97f0>] ? pdflush+0x0/0x2a0                                                       
 [<ffffffff8026c204>] ? kthread+0x64/0xc0                                                       
 [<ffffffff8024af20>] ? schedule_tail+0x30/0x80                                                 
 [<ffffffff8020d4fa>] ? child_rip+0xa/0x20                                                      
 [<ffffffff8026c1a0>] ? kthread+0x0/0xc0                                                        
 [<ffffffff8020d4f0>] ? child_rip+0x0/0x20                                                      
sd 3:0:0:0: [sda] Unhandled error code                                                          
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00                                         
end_request: I/O error, dev sda, sector 126637417                                               
sd 3:0:0:0: [sda] Unhandled error code                                                          
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00                                         
end_request: I/O error, dev sda, sector 126637417                                               
sd 3:0:0:0: [sda] Unhandled error code                                                          
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00                                         
end_request: I/O error, dev sda, sector 126637417                                               
sd 3:0:0:0: [sda] Unhandled error code                                                          
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00                                         
end_request: I/O error, dev sda, sector 126637417
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126637417
done.
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 130097993
EXT4-fs error (device sda2): ext4_find_entry: reading directory #139292 offset 0
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126637417
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126004889
EXT4-fs error (device sda2): ext4_find_entry: reading directory #98457 offset 0
sd 3:0:0:0: [sda] Unhandled error code
sd 3:0:0:0: [sda] Result: hostbyte=0x04 driverbyte=0x00
end_request: I/O error, dev sda, sector 126004889
EXT4-fs error (device sda2): ext4_find_entry: reading directory #98457 offset 0

ANY help would be much appreciated.

Last edited by Cappy (2009-08-10 08:19:09)

Offline

#2 2009-08-10 08:15:26

Cappy
Member
Registered: 2008-10-13
Posts: 20

Re: [Solved] Laptop Suspend puts Hard Drive into Read-Only

Nevermind .. *sigh* ... pci=msi on the kernel fixed it .. going to go cut myself now ...

Offline

Board footer

Powered by FluxBB