Wired and Wireless sometimes work (mostly not) after update.

fowler · 2009-08-15 20:36:25

So I have an issue with my network connection. It sometimes works, sometimes doesn't (mostly doesn't). This is for both wired and wireless. This started to happen a couple of days ago after an update. I had not updated for about a month prior. Prior to the update I used WICD and it worked just fine with no problems. I have no exotic hardware (ipw2200 using its firmware, dell xps gen2 notebook) and I set up everything about 6 months ago based on all the wikis. I have a dlink dir-825 router. Both wired and wireless connections work in windows every boot so it's not hardware.

I've included as much info as possible... sorry for the length.

Things I've tried:
Removing the ! from the INTERFACES=(!eth0 !eth1) in rc.conf
Removing netfs from the daemons
all the hostnames match in hosts and rc.conf

Here is my rc.conf

#
# /etc/rc.conf - Main Configuration for Arch Linux
#

# -----------------------------------------------------------------------
# LOCALIZATION
# -----------------------------------------------------------------------
#
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
#
LOCALE="en_US.utf8"
HARDWARECLOCK="local"
USEDIRECTISA="no"
TIMEZONE="America/New_York"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"

# -----------------------------------------------------------------------
# HARDWARE
# -----------------------------------------------------------------------
#
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
#
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
#
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(acpi-cpufreq cpufreq_ondemand cpufreq_powersave cpufreq_conservative cpufreq_userspace fuse ipw2200)

# Scan for LVM volume groups at startup, required if you use LVM
USELVM="yes"

# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
#
HOSTNAME="stupendiousman"

# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
#
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
INTERFACES=(!eth0 !eth1)

# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
#
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)

# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network.d
#
# This now requires the netcfg package
#
#NETWORKS=(main)

# -----------------------------------------------------------------------
# DAEMONS
# -----------------------------------------------------------------------
#
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
#
DAEMONS=(syslog-ng hal cpufreq wicd alsa crond fam bluetooth)

Here is my hosts

#
# /etc/hosts: static lookup table for host names
#

#<ip-address> <hostname.domain.org> <hostname>
127.0.0.1 localhost.localdomain localhost stupendiousman

# End of file

Here is my mkinitcpio.conf

# vim:set ft=sh
# MODULES
# The following modules are loaded before any boot hooks are
# run. Advanced users may wish to specify all system modules
# in this array. For instance:
# MODULES="piix ide_disk reiserfs"
MODULES=""
CRYPTO_MODULES="aes_generic aes_i586 dm_crypt xts"

# BINARIES
# This setting includes, into the CPIO image, and additional
# binaries a given user may wish. This is run first, so may
# be used to override the actual binaries used in a given hook.
# (Existing files are NOT overwritten is already added)
# BINARIES are dependancy parsed, so you may safely ignore libraries
BINARIES=""

# FILES
# This setting is similar to BINARIES above, however, files are added
# as-is and are not parsed in anyway. This is useful for config files.
# Some users may wish to include modprobe.conf for custom module options,
# like so:
# FILES="/etc/modprobe.conf"
FILES=""

# HOOKS
# This is the most important setting in this file. The HOOKS control the
# modules and scripts added to the image, and what happens at boot time.
# Order is important, and it is recommended that you do not change the
# order in which HOOKS are added. Run 'mkinitcpio -H <hook name>' for
# help on a given hook.
# 'base' is _required_ unless you know precisely what you are doing.
# 'udev' is _required_ in order to automatically load modules
# 'modload' may be used in place of 'udev', but is not recommended
# 'filesystems' is _required_ unless you specify your fs modules in MODULES
# Examples:
# This setup specifies all modules in the MODULES setting above.
# No raid, lvm2, or encrypted root is needed.
# HOOKS="base"
#
# This setup will autodetect all modules for your system and should
# work as a sane default
# HOOKS="base udev autodetect pata scsi sata filesystems"
#
# This is identical to the above, except the old ide subsystem is
# used for IDE devices instead of the new pata subsystem.
# HOOKS="base udev autodetect ide scsi sata filesystems"
#
# This setup will generate a 'full' image which supports most systems.
# No autodetection is done.
# HOOKS="base udev pata scsi sata usb filesystems"
#
# This setup assembles an pata raid array with an encrypted root FS.
# Note: See 'mkinitcpio -H raid' for more information on raid devices.
# HOOKS="base udev pata raid encrypt filesystems"
#
# This setup loads an lvm2 volume group on a usb device.
# HOOKS="base udev usb lvm2 filesystems"
HOOKS="base udev autodetect pata scsi sata encrypt lvm2 resume filesystems firmware"

lspci

00:00.0 Host bridge: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller (rev 03)
00:01.0 PCI bridge: Intel Corporation Mobile 915GM/PM Express PCI Express Root Port (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev d3)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
00:1e.3 Modem: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Modem Controller (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge (rev 03)
00:1f.2 IDE interface: Intel Corporation 82801FBM (ICH6M) SATA Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
01:00.0 VGA compatible controller: nVidia Corporation NV41.9 [GeForce Go 6800 Ultra] (rev a2)
03:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5705M_2 Gigabit Ethernet (rev 03)
03:01.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev b3)
03:01.1 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 08)
03:01.2 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 17)
03:03.0 Network controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection (rev 05)

ifconfig returns:
[rick@stupendiousman ~]$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:12:F0:3E:CA:66
inet6 addr: fe80::212:f0ff:fe3e:ca66/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:25 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:4454 (4.3 Kb)
Interrupt:17 Base address:0x6000 Memory:dcfef000-dcfeffff

eth1 Link encap:Ethernet HWaddr 00:11:43:72:B5:96
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:18

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:4 errors:0 dropped:0 overruns:0 frame:0
TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:280 (280.0 b) TX bytes:280 (280.0 b)

If I do a iwlist scan I get:
[rick@stupendiousman ~]$ iwlist scan
lo Interface doesn't support scanning.

eth0 No scan results

eth1 Interface doesn't support scanning.

pan0 Interface doesn't support scanning.

Here is a portion of my /var/log/wicd/wicd.log

2009/08/15 09:19:29 :: ---------------------------
2009/08/15 09:19:29 :: wicd initializing...
2009/08/15 09:19:29 :: ---------------------------
2009/08/15 09:19:29 :: wicd is version 1.6.2 436
2009/08/15 09:19:29 :: setting backend to external
2009/08/15 09:19:29 :: trying to load backend external
2009/08/15 09:19:30 :: successfully loaded backend external
2009/08/15 09:19:30 :: trying to load backend external
2009/08/15 09:19:30 :: successfully loaded backend external
2009/08/15 09:19:30 :: Automatically detected wireless interface eth0
2009/08/15 09:19:30 :: setting wireless interface eth1
2009/08/15 09:19:30 :: automatically detected wired interface eth1
2009/08/15 09:19:30 :: setting wired interface eth0
2009/08/15 09:19:30 :: setting wpa driver wext
2009/08/15 09:19:30 :: setting use global dns to False
2009/08/15 09:19:30 :: setting global dns
2009/08/15 09:19:30 :: global dns servers are None None None
2009/08/15 09:19:30 :: domain is None
2009/08/15 09:19:30 :: search domain is None
2009/08/15 09:19:30 :: setting automatically reconnect when connection drops True
2009/08/15 09:19:30 :: Setting dhcp client to 0
2009/08/15 09:19:30 :: Wireless configuration file found...
2009/08/15 09:19:30 :: Wired configuration file found...
2009/08/15 09:19:30 :: chmoding configuration files 0600...
2009/08/15 09:19:30 :: chowning configuration files root:root...
2009/08/15 09:19:30 :: Using wireless interface...eth1
2009/08/15 09:19:30 :: Using wired interface...eth0
2009/08/15 09:19:36 :: Autoconnecting...
2009/08/15 09:19:39 :: Attempting to autoconnect with wired interface...
2009/08/15 09:19:39 :: Putting interface down
2009/08/15 09:19:39 :: Releasing DHCP leases...
2009/08/15 09:19:39 :: Setting false IP...
2009/08/15 09:19:39 :: Flushing the routing table...
2009/08/15 09:19:39 :: Putting interface up...
2009/08/15 09:19:39 :: Running DHCP
2009/08/15 09:19:39 :: dhcpcd: version 5.0.6 starting
2009/08/15 09:19:39 ::
2009/08/15 09:19:39 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 09:19:39 ::
2009/08/15 09:20:09 :: dhcpcd: timed out
2009/08/15 09:20:09 ::
2009/08/15 09:20:09 :: DHCP connection failed
2009/08/15 09:20:09 :: exiting connection thread
2009/08/15 09:20:11 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 09:20:11 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 09:20:11 :: Sending connection attempt result dhcp_failed
2009/08/15 09:21:03 :: trying to load backend ioctl
2009/08/15 09:21:03 :: WARNING: python-iwscan not found, falling back to using iwlist scan.
2009/08/15 09:21:03 :: WARNING: python-wpactrl not found, falling back to using wpa_cli.
2009/08/15 09:21:03 :: trying to load backend external
2009/08/15 09:21:10 :: Putting interface down
2009/08/15 09:21:10 :: Releasing DHCP leases...
2009/08/15 09:21:10 :: Setting false IP...
2009/08/15 09:21:10 :: Flushing the routing table...
2009/08/15 09:21:10 :: Putting interface up...
2009/08/15 09:21:10 :: Running DHCP
2009/08/15 09:21:10 :: dhcpcd: version 5.0.6 starting
2009/08/15 09:21:10 ::
2009/08/15 09:21:10 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 09:21:10 ::
2009/08/15 09:21:40 :: dhcpcd: timed out
2009/08/15 09:21:40 ::
2009/08/15 09:21:40 :: DHCP connection failed
2009/08/15 09:21:40 :: exiting connection thread
2009/08/15 09:21:40 :: Sending connection attempt result dhcp_failed
2009/08/15 09:22:28 :: Putting interface down
2009/08/15 09:22:28 :: Releasing DHCP leases...
2009/08/15 09:22:28 :: Setting false IP...
2009/08/15 09:22:28 :: Flushing the routing table...
2009/08/15 09:22:28 :: Putting interface up...
2009/08/15 09:22:28 :: Running DHCP
2009/08/15 09:22:28 :: dhcpcd: version 5.0.6 starting
2009/08/15 09:22:28 ::
2009/08/15 09:22:28 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 09:22:28 ::
2009/08/15 09:22:58 :: dhcpcd: timed out
2009/08/15 09:22:58 ::
2009/08/15 09:22:58 :: DHCP connection failed
2009/08/15 09:22:58 :: exiting connection thread
2009/08/15 09:22:58 :: Sending connection attempt result dhcp_failed
2009/08/15 09:23:17 :: Daemon going down, killing wicd-monitor...
2009/08/15 09:23:17 :: Removing PID file...
2009/08/15 09:23:17 :: Shutting down...
2009/08/15 13:16:59 :: ---------------------------
2009/08/15 13:16:59 :: wicd initializing...
2009/08/15 13:16:59 :: ---------------------------
2009/08/15 13:16:59 :: wicd is version 1.6.2 436
2009/08/15 13:16:59 :: setting backend to external
2009/08/15 13:16:59 :: trying to load backend external
2009/08/15 13:17:00 :: successfully loaded backend external
2009/08/15 13:17:00 :: trying to load backend external
2009/08/15 13:17:00 :: successfully loaded backend external
2009/08/15 13:17:00 :: Automatically detected wireless interface eth0
2009/08/15 13:17:00 :: setting wireless interface eth1
2009/08/15 13:17:00 :: automatically detected wired interface eth1
2009/08/15 13:17:00 :: setting wired interface eth0
2009/08/15 13:17:00 :: setting wpa driver wext
2009/08/15 13:17:00 :: setting use global dns to False
2009/08/15 13:17:00 :: setting global dns
2009/08/15 13:17:00 :: global dns servers are None None None
2009/08/15 13:17:00 :: domain is None
2009/08/15 13:17:00 :: search domain is None
2009/08/15 13:17:00 :: setting automatically reconnect when connection drops True
2009/08/15 13:17:00 :: Setting dhcp client to 0
2009/08/15 13:17:00 :: Wireless configuration file found...
2009/08/15 13:17:00 :: Wired configuration file found...
2009/08/15 13:17:00 :: chmoding configuration files 0600...
2009/08/15 13:17:00 :: chowning configuration files root:root...
2009/08/15 13:17:00 :: Using wireless interface...eth1
2009/08/15 13:17:00 :: Using wired interface...eth0
2009/08/15 13:17:06 :: Autoconnecting...
2009/08/15 13:17:09 :: Attempting to autoconnect with wired interface...
2009/08/15 13:17:09 :: Putting interface down
2009/08/15 13:17:09 :: Releasing DHCP leases...
2009/08/15 13:17:09 :: Setting false IP...
2009/08/15 13:17:09 :: Flushing the routing table...
2009/08/15 13:17:09 :: Putting interface up...
2009/08/15 13:17:09 :: Running DHCP
2009/08/15 13:17:09 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:17:09 ::
2009/08/15 13:17:09 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:17:09 ::
2009/08/15 13:17:39 :: dhcpcd: timed out
2009/08/15 13:17:39 ::
2009/08/15 13:17:39 :: DHCP connection failed
2009/08/15 13:17:39 :: exiting connection thread
2009/08/15 13:17:41 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:17:41 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:17:41 :: Sending connection attempt result dhcp_failed
2009/08/15 13:18:10 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:18:10 :: Removing PID file...
2009/08/15 13:18:10 :: Shutting down...
2009/08/15 13:19:01 :: ---------------------------
2009/08/15 13:19:01 :: wicd initializing...
2009/08/15 13:19:01 :: ---------------------------
2009/08/15 13:19:01 :: wicd is version 1.6.2 436
2009/08/15 13:19:01 :: setting backend to external
2009/08/15 13:19:01 :: trying to load backend external
2009/08/15 13:19:02 :: successfully loaded backend external
2009/08/15 13:19:02 :: trying to load backend external
2009/08/15 13:19:02 :: successfully loaded backend external
2009/08/15 13:19:02 :: Automatically detected wireless interface eth0
2009/08/15 13:19:02 :: setting wireless interface eth1
2009/08/15 13:19:02 :: automatically detected wired interface eth1
2009/08/15 13:19:02 :: setting wired interface eth0
2009/08/15 13:19:02 :: setting wpa driver wext
2009/08/15 13:19:02 :: setting use global dns to False
2009/08/15 13:19:02 :: setting global dns
2009/08/15 13:19:02 :: global dns servers are None None None
2009/08/15 13:19:02 :: domain is None
2009/08/15 13:19:02 :: search domain is None
2009/08/15 13:19:02 :: setting automatically reconnect when connection drops True
2009/08/15 13:19:02 :: Setting dhcp client to 0
2009/08/15 13:19:02 :: Wireless configuration file found...
2009/08/15 13:19:02 :: Wired configuration file found...
2009/08/15 13:19:02 :: chmoding configuration files 0600...
2009/08/15 13:19:02 :: chowning configuration files root:root...
2009/08/15 13:19:02 :: Using wireless interface...eth1
2009/08/15 13:19:02 :: Using wired interface...eth0
2009/08/15 13:19:08 :: Autoconnecting...
2009/08/15 13:19:11 :: Attempting to autoconnect with wired interface...
2009/08/15 13:19:11 :: Putting interface down
2009/08/15 13:19:11 :: Releasing DHCP leases...
2009/08/15 13:19:11 :: Setting false IP...
2009/08/15 13:19:11 :: Flushing the routing table...
2009/08/15 13:19:11 :: Putting interface up...
2009/08/15 13:19:11 :: Running DHCP
2009/08/15 13:19:11 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:19:11 ::
2009/08/15 13:19:11 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:19:11 ::
2009/08/15 13:19:41 :: dhcpcd: timed out
2009/08/15 13:19:41 ::
2009/08/15 13:19:41 :: DHCP connection failed
2009/08/15 13:19:41 :: exiting connection thread
2009/08/15 13:19:43 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:19:43 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:19:43 :: Sending connection attempt result dhcp_failed
2009/08/15 13:30:36 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:30:36 :: Removing PID file...
2009/08/15 13:30:36 :: Shutting down...
2009/08/15 13:31:29 :: ---------------------------
2009/08/15 13:31:29 :: wicd initializing...
2009/08/15 13:31:29 :: ---------------------------
2009/08/15 13:31:29 :: wicd is version 1.6.2 436
2009/08/15 13:31:29 :: setting backend to external
2009/08/15 13:31:29 :: trying to load backend external
2009/08/15 13:31:30 :: successfully loaded backend external
2009/08/15 13:31:30 :: trying to load backend external
2009/08/15 13:31:30 :: successfully loaded backend external
2009/08/15 13:31:30 :: Automatically detected wireless interface eth0
2009/08/15 13:31:30 :: setting wireless interface eth1
2009/08/15 13:31:30 :: automatically detected wired interface eth1
2009/08/15 13:31:30 :: setting wired interface eth0
2009/08/15 13:31:30 :: setting wpa driver wext
2009/08/15 13:31:30 :: setting use global dns to False
2009/08/15 13:31:30 :: setting global dns
2009/08/15 13:31:30 :: global dns servers are None None None
2009/08/15 13:31:30 :: domain is None
2009/08/15 13:31:30 :: search domain is None
2009/08/15 13:31:30 :: setting automatically reconnect when connection drops True
2009/08/15 13:31:30 :: Setting dhcp client to 0
2009/08/15 13:31:30 :: Wireless configuration file found...
2009/08/15 13:31:30 :: Wired configuration file found...
2009/08/15 13:31:30 :: chmoding configuration files 0600...
2009/08/15 13:31:30 :: chowning configuration files root:root...
2009/08/15 13:31:30 :: Using wireless interface...eth1
2009/08/15 13:31:30 :: Using wired interface...eth0
2009/08/15 13:31:37 :: Autoconnecting...
2009/08/15 13:31:39 :: Attempting to autoconnect with wired interface...
2009/08/15 13:31:39 :: Putting interface down
2009/08/15 13:31:39 :: Releasing DHCP leases...
2009/08/15 13:31:39 :: Setting false IP...
2009/08/15 13:31:39 :: Flushing the routing table...
2009/08/15 13:31:39 :: Putting interface up...
2009/08/15 13:31:39 :: Running DHCP
2009/08/15 13:31:39 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:31:39 ::
2009/08/15 13:31:40 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:31:40 ::
2009/08/15 13:32:09 :: dhcpcd: timed out
2009/08/15 13:32:09 ::
2009/08/15 13:32:09 :: DHCP connection failed
2009/08/15 13:32:09 :: exiting connection thread
2009/08/15 13:32:12 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:32:12 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:32:12 :: Sending connection attempt result dhcp_failed
2009/08/15 13:38:00 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:38:00 :: Removing PID file...
2009/08/15 13:38:00 :: Shutting down...
2009/08/15 13:39:19 :: ---------------------------
2009/08/15 13:39:19 :: wicd initializing...
2009/08/15 13:39:19 :: ---------------------------
2009/08/15 13:39:19 :: wicd is version 1.6.2 436
2009/08/15 13:39:19 :: setting backend to external
2009/08/15 13:39:19 :: trying to load backend external
2009/08/15 13:39:20 :: successfully loaded backend external
2009/08/15 13:39:20 :: trying to load backend external
2009/08/15 13:39:20 :: successfully loaded backend external
2009/08/15 13:39:20 :: Automatically detected wireless interface eth0
2009/08/15 13:39:20 :: setting wireless interface eth1
2009/08/15 13:39:20 :: automatically detected wired interface eth1
2009/08/15 13:39:20 :: setting wired interface eth0
2009/08/15 13:39:20 :: setting wpa driver wext
2009/08/15 13:39:20 :: setting use global dns to False
2009/08/15 13:39:20 :: setting global dns
2009/08/15 13:39:20 :: global dns servers are None None None
2009/08/15 13:39:20 :: domain is None
2009/08/15 13:39:20 :: search domain is None
2009/08/15 13:39:20 :: setting automatically reconnect when connection drops True
2009/08/15 13:39:20 :: Setting dhcp client to 0
2009/08/15 13:39:20 :: Wireless configuration file found...
2009/08/15 13:39:20 :: Wired configuration file found...
2009/08/15 13:39:20 :: chmoding configuration files 0600...
2009/08/15 13:39:20 :: chowning configuration files root:root...
2009/08/15 13:39:20 :: Using wireless interface...eth1
2009/08/15 13:39:20 :: Using wired interface...eth0
2009/08/15 13:39:27 :: Autoconnecting...
2009/08/15 13:39:29 :: Attempting to autoconnect with wired interface...
2009/08/15 13:39:29 :: Putting interface down
2009/08/15 13:39:29 :: Releasing DHCP leases...
2009/08/15 13:39:29 :: Setting false IP...
2009/08/15 13:39:29 :: Flushing the routing table...
2009/08/15 13:39:29 :: Putting interface up...
2009/08/15 13:39:29 :: Running DHCP
2009/08/15 13:39:29 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:39:29 ::
2009/08/15 13:39:30 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:39:30 ::
2009/08/15 13:39:59 :: dhcpcd: timed out
2009/08/15 13:39:59 ::
2009/08/15 13:39:59 :: DHCP connection failed
2009/08/15 13:39:59 :: exiting connection thread
2009/08/15 13:40:02 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:40:02 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:40:02 :: Sending connection attempt result dhcp_failed
2009/08/15 13:45:10 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:45:10 :: Removing PID file...
2009/08/15 13:45:10 :: Shutting down...
2009/08/15 13:46:13 :: ---------------------------
2009/08/15 13:46:13 :: wicd initializing...
2009/08/15 13:46:13 :: ---------------------------
2009/08/15 13:46:13 :: wicd is version 1.6.2 436
2009/08/15 13:46:13 :: setting backend to external
2009/08/15 13:46:13 :: trying to load backend external
2009/08/15 13:46:14 :: successfully loaded backend external
2009/08/15 13:46:14 :: trying to load backend external
2009/08/15 13:46:14 :: successfully loaded backend external
2009/08/15 13:46:14 :: Automatically detected wireless interface eth1
2009/08/15 13:46:14 :: setting wireless interface eth1
2009/08/15 13:46:14 :: automatically detected wired interface eth0
2009/08/15 13:46:14 :: setting wired interface eth0
2009/08/15 13:46:14 :: setting wpa driver wext
2009/08/15 13:46:14 :: setting use global dns to False
2009/08/15 13:46:14 :: setting global dns
2009/08/15 13:46:14 :: global dns servers are None None None
2009/08/15 13:46:14 :: domain is None
2009/08/15 13:46:14 :: search domain is None
2009/08/15 13:46:14 :: setting automatically reconnect when connection drops True
2009/08/15 13:46:14 :: Setting dhcp client to 0
2009/08/15 13:46:14 :: Wireless configuration file found...
2009/08/15 13:46:14 :: Wired configuration file found...
2009/08/15 13:46:14 :: chmoding configuration files 0600...
2009/08/15 13:46:14 :: chowning configuration files root:root...
2009/08/15 13:46:14 :: Using wireless interface...eth1
2009/08/15 13:46:14 :: Using wired interface...eth0
2009/08/15 13:46:20 :: Autoconnecting...
2009/08/15 13:46:22 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:46:22 :: trying to automatically connect to...101
2009/08/15 13:46:22 :: Connecting to wireless network 101
2009/08/15 13:46:23 :: Putting interface down
2009/08/15 13:46:23 :: Releasing DHCP leases...
2009/08/15 13:46:23 :: Setting false IP...
2009/08/15 13:46:23 :: Stopping wpa_supplicant
2009/08/15 13:46:23 :: Flushing the routing table...
2009/08/15 13:46:23 :: Putting interface up...
2009/08/15 13:46:23 :: Generating psk...
2009/08/15 13:46:23 :: Attempting to authenticate...
2009/08/15 13:46:34 :: Running DHCP
2009/08/15 13:46:34 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:46:34 ::
2009/08/15 13:46:34 :: dhcpcd: eth1: broadcasting for a lease
2009/08/15 13:46:34 ::
2009/08/15 13:46:35 :: dhcpcd: eth1: offered 192.168.0.183 from 192.168.0.1
2009/08/15 13:46:35 ::
2009/08/15 13:46:35 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 13:46:35 ::
2009/08/15 13:46:35 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 13:46:35 ::
2009/08/15 13:46:38 :: dhcpcd: eth1: carrier lost
2009/08/15 13:46:38 ::
2009/08/15 13:46:40 :: dhcpcd: eth1: carrier acquired
2009/08/15 13:46:40 ::
2009/08/15 13:46:40 :: dhcpcd: eth1: broadcasting for a lease
2009/08/15 13:46:40 ::
2009/08/15 13:46:45 :: dhcpcd: eth1: offered 192.168.0.183 from 192.168.0.1
2009/08/15 13:46:45 ::
2009/08/15 13:46:45 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 13:46:45 ::
2009/08/15 13:46:45 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 13:46:45 ::
2009/08/15 13:46:51 :: dhcpcd: eth1: leased 192.168.0.183 for 86400 seconds
2009/08/15 13:46:51 ::
2009/08/15 13:46:51 :: dhcpcd: forking to background
2009/08/15 13:46:51 ::
2009/08/15 13:46:51 ::
2009/08/15 13:46:51 :: DHCP connection successful
2009/08/15 13:46:51 :: Connecting thread exiting.
2009/08/15 13:46:55 :: Sending connection attempt result Success
2009/08/15 13:48:50 :: Putting interface down
2009/08/15 13:48:50 :: Releasing DHCP leases...
2009/08/15 13:48:50 :: Setting false IP...
2009/08/15 13:48:51 :: Flushing the routing table...
2009/08/15 13:48:51 :: Putting interface up...
2009/08/15 13:48:51 :: Running DHCP
2009/08/15 13:48:51 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:48:51 ::
2009/08/15 13:48:51 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:48:51 ::
2009/08/15 13:48:51 :: dhcpcd: eth0: carrier lost
2009/08/15 13:48:51 ::
2009/08/15 13:48:53 :: dhcpcd: eth0: carrier acquired
2009/08/15 13:48:53 ::
2009/08/15 13:48:53 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:48:53 ::
2009/08/15 13:48:54 :: dhcpcd: eth0: offered 192.168.0.193 from 192.168.0.1
2009/08/15 13:48:54 ::
2009/08/15 13:48:54 :: dhcpcd: eth0: acknowledged 192.168.0.193 from 192.168.0.1
2009/08/15 13:48:54 ::
2009/08/15 13:48:54 :: dhcpcd: eth0: checking for 192.168.0.193
2009/08/15 13:48:54 ::
2009/08/15 13:49:00 :: dhcpcd: eth0: leased 192.168.0.193 for 86400 seconds
2009/08/15 13:49:00 ::
2009/08/15 13:49:00 :: dhcpcd: forking to background
2009/08/15 13:49:00 ::
2009/08/15 13:49:00 ::
2009/08/15 13:49:00 :: DHCP connection successful
2009/08/15 13:49:00 :: Connecting thread exiting.
2009/08/15 13:49:00 :: Sending connection attempt result Success
2009/08/15 13:53:46 :: Connecting to wireless network 102
2009/08/15 13:53:47 :: Putting interface down
2009/08/15 13:53:47 :: Releasing DHCP leases...
2009/08/15 13:53:47 :: Setting false IP...
2009/08/15 13:53:47 :: Stopping wpa_supplicant
2009/08/15 13:53:47 :: Flushing the routing table...
2009/08/15 13:53:47 :: Putting interface up...
2009/08/15 13:53:47 :: Generating psk...
2009/08/15 13:53:47 :: Attempting to authenticate...
2009/08/15 13:54:03 :: Running DHCP
2009/08/15 13:54:03 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:54:03 ::
2009/08/15 13:54:03 :: dhcpcd: eth1: rebinding lease of 192.168.0.183
2009/08/15 13:54:03 ::
2009/08/15 13:54:03 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 13:54:03 ::
2009/08/15 13:54:03 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 13:54:03 ::
2009/08/15 13:54:05 :: dhcpcd: eth1: carrier lost
2009/08/15 13:54:05 ::
2009/08/15 13:54:06 :: dhcpcd: eth1: carrier acquired
2009/08/15 13:54:06 ::
2009/08/15 13:54:06 :: dhcpcd: eth1: rebinding lease of 192.168.0.183
2009/08/15 13:54:06 ::
2009/08/15 13:54:06 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 13:54:06 ::
2009/08/15 13:54:06 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 13:54:06 ::
2009/08/15 13:54:11 :: dhcpcd: eth1: leased 192.168.0.183 for 86400 seconds
2009/08/15 13:54:11 ::
2009/08/15 13:54:11 :: dhcpcd: forking to background
2009/08/15 13:54:11 ::
2009/08/15 13:54:11 ::
2009/08/15 13:54:11 :: DHCP connection successful
2009/08/15 13:54:11 :: Connecting thread exiting.
2009/08/15 13:54:11 :: Sending connection attempt result Success
2009/08/15 13:55:03 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:55:03 :: Removing PID file...
2009/08/15 13:55:03 :: Shutting down...
2009/08/15 13:55:52 :: ---------------------------
2009/08/15 13:55:52 :: wicd initializing...
2009/08/15 13:55:52 :: ---------------------------
2009/08/15 13:55:52 :: wicd is version 1.6.2 436
2009/08/15 13:55:52 :: setting backend to external
2009/08/15 13:55:52 :: trying to load backend external
2009/08/15 13:55:53 :: successfully loaded backend external
2009/08/15 13:55:53 :: trying to load backend external
2009/08/15 13:55:53 :: successfully loaded backend external
2009/08/15 13:55:53 :: Automatically detected wireless interface eth0
2009/08/15 13:55:53 :: setting wireless interface eth1
2009/08/15 13:55:53 :: automatically detected wired interface eth1
2009/08/15 13:55:53 :: setting wired interface eth0
2009/08/15 13:55:53 :: setting wpa driver wext
2009/08/15 13:55:53 :: setting use global dns to False
2009/08/15 13:55:53 :: setting global dns
2009/08/15 13:55:53 :: global dns servers are None None None
2009/08/15 13:55:53 :: domain is None
2009/08/15 13:55:53 :: search domain is None
2009/08/15 13:55:53 :: setting automatically reconnect when connection drops True
2009/08/15 13:55:53 :: Setting dhcp client to 0
2009/08/15 13:55:53 :: Wireless configuration file found...
2009/08/15 13:55:53 :: Wired configuration file found...
2009/08/15 13:55:53 :: chmoding configuration files 0600...
2009/08/15 13:55:53 :: chowning configuration files root:root...
2009/08/15 13:55:53 :: Using wireless interface...eth1
2009/08/15 13:55:53 :: Using wired interface...eth0
2009/08/15 13:55:59 :: Autoconnecting...
2009/08/15 13:56:02 :: Attempting to autoconnect with wired interface...
2009/08/15 13:56:02 :: Putting interface down
2009/08/15 13:56:02 :: Releasing DHCP leases...
2009/08/15 13:56:02 :: Setting false IP...
2009/08/15 13:56:02 :: Flushing the routing table...
2009/08/15 13:56:02 :: Putting interface up...
2009/08/15 13:56:02 :: Running DHCP
2009/08/15 13:56:02 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:56:02 ::
2009/08/15 13:56:02 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 13:56:02 ::
2009/08/15 13:56:12 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:56:12 ::
2009/08/15 13:56:32 :: dhcpcd: timed out
2009/08/15 13:56:32 ::
2009/08/15 13:56:32 :: DHCP connection failed
2009/08/15 13:56:32 :: exiting connection thread
2009/08/15 13:56:34 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:56:34 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:56:34 :: Sending connection attempt result dhcp_failed
2009/08/15 13:57:31 :: Daemon going down, killing wicd-monitor...
2009/08/15 13:57:31 :: Removing PID file...
2009/08/15 13:57:31 :: Shutting down...
2009/08/15 13:57:32 :: ---------------------------
2009/08/15 13:57:32 :: wicd initializing...
2009/08/15 13:57:32 :: ---------------------------
2009/08/15 13:57:32 :: wicd is version 1.6.2 436
2009/08/15 13:57:32 :: setting backend to external
2009/08/15 13:57:32 :: trying to load backend external
2009/08/15 13:57:32 :: successfully loaded backend external
2009/08/15 13:57:32 :: trying to load backend external
2009/08/15 13:57:32 :: successfully loaded backend external
2009/08/15 13:57:32 :: Automatically detected wireless interface eth0
2009/08/15 13:57:32 :: setting wireless interface eth1
2009/08/15 13:57:32 :: automatically detected wired interface eth1
2009/08/15 13:57:32 :: setting wired interface eth0
2009/08/15 13:57:32 :: setting wpa driver wext
2009/08/15 13:57:32 :: setting use global dns to False
2009/08/15 13:57:32 :: setting global dns
2009/08/15 13:57:32 :: global dns servers are None None None
2009/08/15 13:57:32 :: domain is None
2009/08/15 13:57:32 :: search domain is None
2009/08/15 13:57:32 :: setting automatically reconnect when connection drops True
2009/08/15 13:57:32 :: Setting dhcp client to 0
2009/08/15 13:57:32 :: Wireless configuration file found...
2009/08/15 13:57:32 :: Wired configuration file found...
2009/08/15 13:57:32 :: chmoding configuration files 0600...
2009/08/15 13:57:32 :: chowning configuration files root:root...
2009/08/15 13:57:32 :: Using wireless interface...eth1
2009/08/15 13:57:32 :: Using wired interface...eth0
2009/08/15 13:57:38 :: Autoconnecting...
2009/08/15 13:57:38 :: Putting interface down
2009/08/15 13:57:38 :: Attempting to autoconnect with wired interface...
2009/08/15 13:57:38 :: Releasing DHCP leases...
2009/08/15 13:57:38 :: Setting false IP...
2009/08/15 13:57:38 :: Flushing the routing table...
2009/08/15 13:57:38 :: Putting interface up...
2009/08/15 13:57:38 :: Running DHCP
2009/08/15 13:57:38 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:57:38 ::
2009/08/15 13:57:38 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 13:57:38 ::
2009/08/15 13:57:48 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:57:48 ::
2009/08/15 13:58:08 :: dhcpcd: timed out
2009/08/15 13:58:08 ::
2009/08/15 13:58:08 :: DHCP connection failed
2009/08/15 13:58:08 :: exiting connection thread
2009/08/15 13:58:08 :: Sending connection attempt result dhcp_failed
2009/08/15 13:58:10 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 13:58:10 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 13:58:46 :: Putting interface down
2009/08/15 13:58:46 :: Releasing DHCP leases...
2009/08/15 13:58:46 :: Setting false IP...
2009/08/15 13:58:46 :: Flushing the routing table...
2009/08/15 13:58:46 :: Putting interface up...
2009/08/15 13:58:46 :: Running DHCP
2009/08/15 13:58:46 :: dhcpcd: version 5.0.6 starting
2009/08/15 13:58:46 ::
2009/08/15 13:58:46 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 13:58:46 ::
2009/08/15 13:58:56 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 13:58:56 ::
2009/08/15 13:59:16 :: dhcpcd: timed out
2009/08/15 13:59:16 ::
2009/08/15 13:59:16 :: DHCP connection failed
2009/08/15 13:59:16 :: exiting connection thread
2009/08/15 13:59:16 :: Sending connection attempt result dhcp_failed
2009/08/15 14:10:08 :: Daemon going down, killing wicd-monitor...
2009/08/15 14:10:08 :: Removing PID file...
2009/08/15 14:10:08 :: Shutting down...
2009/08/15 14:10:59 :: ---------------------------
2009/08/15 14:10:59 :: wicd initializing...
2009/08/15 14:10:59 :: ---------------------------
2009/08/15 14:10:59 :: wicd is version 1.6.2 436
2009/08/15 14:10:59 :: setting backend to external
2009/08/15 14:10:59 :: trying to load backend external
2009/08/15 14:10:59 :: successfully loaded backend external
2009/08/15 14:10:59 :: trying to load backend external
2009/08/15 14:10:59 :: successfully loaded backend external
2009/08/15 14:10:59 :: Automatically detected wireless interface eth0
2009/08/15 14:10:59 :: setting wireless interface eth1
2009/08/15 14:10:59 :: automatically detected wired interface eth1
2009/08/15 14:10:59 :: setting wired interface eth0
2009/08/15 14:10:59 :: setting wpa driver wext
2009/08/15 14:10:59 :: setting use global dns to False
2009/08/15 14:10:59 :: setting global dns
2009/08/15 14:10:59 :: global dns servers are None None None
2009/08/15 14:10:59 :: domain is None
2009/08/15 14:10:59 :: search domain is None
2009/08/15 14:10:59 :: setting automatically reconnect when connection drops True
2009/08/15 14:10:59 :: Setting dhcp client to 0
2009/08/15 14:10:59 :: Wireless configuration file found...
2009/08/15 14:10:59 :: Wired configuration file found...
2009/08/15 14:10:59 :: chmoding configuration files 0600...
2009/08/15 14:10:59 :: chowning configuration files root:root...
2009/08/15 14:10:59 :: Using wireless interface...eth1
2009/08/15 14:10:59 :: Using wired interface...eth0
2009/08/15 14:11:06 :: Autoconnecting...
2009/08/15 14:11:09 :: Attempting to autoconnect with wired interface...
2009/08/15 14:11:09 :: Putting interface down
2009/08/15 14:11:09 :: Releasing DHCP leases...
2009/08/15 14:11:09 :: Setting false IP...
2009/08/15 14:11:09 :: Flushing the routing table...
2009/08/15 14:11:09 :: Putting interface up...
2009/08/15 14:11:09 :: Running DHCP
2009/08/15 14:11:09 :: dhcpcd: version 5.0.6 starting
2009/08/15 14:11:09 ::
2009/08/15 14:11:09 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 14:11:09 ::
2009/08/15 14:11:19 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 14:11:19 ::
2009/08/15 14:11:39 :: dhcpcd: timed out
2009/08/15 14:11:39 ::
2009/08/15 14:11:39 :: DHCP connection failed
2009/08/15 14:11:39 :: exiting connection thread
2009/08/15 14:11:41 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 14:11:41 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 14:11:41 :: Sending connection attempt result dhcp_failed
2009/08/15 14:13:00 :: Daemon going down, killing wicd-monitor...
2009/08/15 14:13:00 :: Removing PID file...
2009/08/15 14:13:00 :: Shutting down...
2009/08/15 14:13:50 :: ---------------------------
2009/08/15 14:13:50 :: wicd initializing...
2009/08/15 14:13:50 :: ---------------------------
2009/08/15 14:13:50 :: wicd is version 1.6.2 436
2009/08/15 14:13:50 :: setting backend to external
2009/08/15 14:13:50 :: trying to load backend external
2009/08/15 14:13:50 :: successfully loaded backend external
2009/08/15 14:13:50 :: trying to load backend external
2009/08/15 14:13:50 :: successfully loaded backend external
2009/08/15 14:13:51 :: Automatically detected wireless interface eth1
2009/08/15 14:13:51 :: setting wireless interface eth1
2009/08/15 14:13:51 :: automatically detected wired interface eth0
2009/08/15 14:13:51 :: setting wired interface eth0
2009/08/15 14:13:51 :: setting wpa driver wext
2009/08/15 14:13:51 :: setting use global dns to False
2009/08/15 14:13:51 :: setting global dns
2009/08/15 14:13:51 :: global dns servers are None None None
2009/08/15 14:13:51 :: domain is None
2009/08/15 14:13:51 :: search domain is None
2009/08/15 14:13:51 :: setting automatically reconnect when connection drops True
2009/08/15 14:13:51 :: Setting dhcp client to 0
2009/08/15 14:13:51 :: Wireless configuration file found...
2009/08/15 14:13:51 :: Wired configuration file found...
2009/08/15 14:13:51 :: chmoding configuration files 0600...
2009/08/15 14:13:51 :: chowning configuration files root:root...
2009/08/15 14:13:51 :: Using wireless interface...eth1
2009/08/15 14:13:51 :: Using wired interface...eth0
2009/08/15 14:13:57 :: Autoconnecting...
2009/08/15 14:13:59 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 14:14:00 :: trying to automatically connect to...101
2009/08/15 14:14:00 :: Connecting to wireless network 101
2009/08/15 14:14:00 :: Putting interface down
2009/08/15 14:14:00 :: Releasing DHCP leases...
2009/08/15 14:14:00 :: Setting false IP...
2009/08/15 14:14:00 :: Stopping wpa_supplicant
2009/08/15 14:14:00 :: Flushing the routing table...
2009/08/15 14:14:00 :: Putting interface up...
2009/08/15 14:14:00 :: Generating psk...
2009/08/15 14:14:01 :: Attempting to authenticate...
2009/08/15 14:14:11 :: Running DHCP
2009/08/15 14:14:11 :: dhcpcd: version 5.0.6 starting
2009/08/15 14:14:11 ::
2009/08/15 14:14:11 :: dhcpcd: eth1: rebinding lease of 192.168.0.183
2009/08/15 14:14:11 ::
2009/08/15 14:14:11 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 14:14:11 ::
2009/08/15 14:14:11 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 14:14:11 ::
2009/08/15 14:14:15 :: dhcpcd: eth1: leased 192.168.0.183 for 86400 seconds
2009/08/15 14:14:15 ::
2009/08/15 14:14:15 :: dhcpcd: forking to background
2009/08/15 14:14:15 ::
2009/08/15 14:14:15 ::
2009/08/15 14:14:15 :: DHCP connection successful
2009/08/15 14:14:15 :: Connecting thread exiting.
2009/08/15 14:14:17 :: Sending connection attempt result Success
2009/08/15 14:14:17 :: Autoconnecting...
2009/08/15 14:14:17 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 14:14:17 :: trying to automatically connect to...102
2009/08/15 14:14:17 :: Connecting to wireless network 102
2009/08/15 14:14:17 :: Putting interface down
2009/08/15 14:14:17 :: Releasing DHCP leases...
2009/08/15 14:14:18 :: Setting false IP...
2009/08/15 14:14:18 :: Stopping wpa_supplicant
2009/08/15 14:14:18 :: Flushing the routing table...
2009/08/15 14:14:18 :: Putting interface up...
2009/08/15 14:14:18 :: Generating psk...
2009/08/15 14:14:18 :: Attempting to authenticate...
2009/08/15 14:14:19 :: Running DHCP
2009/08/15 14:14:19 :: dhcpcd: version 5.0.6 starting
2009/08/15 14:14:19 ::
2009/08/15 14:14:19 :: dhcpcd: eth1: rebinding lease of 192.168.0.183
2009/08/15 14:14:19 ::
2009/08/15 14:14:19 :: dhcpcd: eth1: acknowledged 192.168.0.183 from 192.168.0.1
2009/08/15 14:14:19 ::
2009/08/15 14:14:19 :: dhcpcd: eth1: checking for 192.168.0.183
2009/08/15 14:14:19 ::
2009/08/15 14:14:24 :: dhcpcd: eth1: leased 192.168.0.183 for 86400 seconds
2009/08/15 14:14:24 ::
2009/08/15 14:14:24 :: dhcpcd: forking to background
2009/08/15 14:14:24 ::
2009/08/15 14:14:24 ::
2009/08/15 14:14:24 :: DHCP connection successful
2009/08/15 14:14:24 :: Connecting thread exiting.
2009/08/15 14:14:29 :: Sending connection attempt result Success
2009/08/15 14:15:02 :: Daemon going down, killing wicd-monitor...
2009/08/15 14:15:02 :: Removing PID file...
2009/08/15 14:15:02 :: Shutting down...
2009/08/15 14:15:52 :: ---------------------------
2009/08/15 14:15:52 :: wicd initializing...
2009/08/15 14:15:52 :: ---------------------------
2009/08/15 14:15:52 :: wicd is version 1.6.2 436
2009/08/15 14:15:52 :: setting backend to external
2009/08/15 14:15:52 :: trying to load backend external
2009/08/15 14:15:52 :: successfully loaded backend external
2009/08/15 14:15:52 :: trying to load backend external
2009/08/15 14:15:52 :: successfully loaded backend external
2009/08/15 14:15:52 :: Automatically detected wireless interface eth0
2009/08/15 14:15:52 :: setting wireless interface eth1
2009/08/15 14:15:52 :: automatically detected wired interface eth1
2009/08/15 14:15:52 :: setting wired interface eth0
2009/08/15 14:15:52 :: setting wpa driver wext
2009/08/15 14:15:52 :: setting use global dns to False
2009/08/15 14:15:52 :: setting global dns
2009/08/15 14:15:52 :: global dns servers are None None None
2009/08/15 14:15:52 :: domain is None
2009/08/15 14:15:52 :: search domain is None
2009/08/15 14:15:52 :: setting automatically reconnect when connection drops True
2009/08/15 14:15:52 :: Setting dhcp client to 0
2009/08/15 14:15:52 :: Wireless configuration file found...
2009/08/15 14:15:52 :: Wired configuration file found...
2009/08/15 14:15:52 :: chmoding configuration files 0600...
2009/08/15 14:15:52 :: chowning configuration files root:root...
2009/08/15 14:15:52 :: Using wireless interface...eth1
2009/08/15 14:15:52 :: Using wired interface...eth0
2009/08/15 14:15:59 :: Autoconnecting...
2009/08/15 14:16:02 :: Attempting to autoconnect with wired interface...
2009/08/15 14:16:02 :: Putting interface down
2009/08/15 14:16:02 :: Releasing DHCP leases...
2009/08/15 14:16:02 :: Setting false IP...
2009/08/15 14:16:02 :: Flushing the routing table...
2009/08/15 14:16:02 :: Putting interface up...
2009/08/15 14:16:02 :: Running DHCP
2009/08/15 14:16:02 :: dhcpcd: version 5.0.6 starting
2009/08/15 14:16:02 ::
2009/08/15 14:16:02 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 14:16:02 ::
2009/08/15 14:16:12 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 14:16:12 ::
2009/08/15 14:16:32 :: dhcpcd: timed out
2009/08/15 14:16:32 ::
2009/08/15 14:16:32 :: DHCP connection failed
2009/08/15 14:16:32 :: exiting connection thread
2009/08/15 14:16:34 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 14:16:34 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 14:16:34 :: Sending connection attempt result dhcp_failed
2009/08/15 14:17:02 :: Daemon going down, killing wicd-monitor...
2009/08/15 14:17:02 :: Removing PID file...
2009/08/15 14:17:02 :: Shutting down...
2009/08/15 15:39:03 :: ---------------------------
2009/08/15 15:39:03 :: wicd initializing...
2009/08/15 15:39:03 :: ---------------------------
2009/08/15 15:39:03 :: wicd is version 1.6.2 436
2009/08/15 15:39:03 :: setting backend to external
2009/08/15 15:39:03 :: trying to load backend external
2009/08/15 15:39:03 :: successfully loaded backend external
2009/08/15 15:39:03 :: trying to load backend external
2009/08/15 15:39:03 :: successfully loaded backend external
2009/08/15 15:39:03 :: Automatically detected wireless interface eth0
2009/08/15 15:39:03 :: setting wireless interface eth1
2009/08/15 15:39:03 :: automatically detected wired interface eth1
2009/08/15 15:39:03 :: setting wired interface eth0
2009/08/15 15:39:03 :: setting wpa driver wext
2009/08/15 15:39:03 :: setting use global dns to False
2009/08/15 15:39:03 :: setting global dns
2009/08/15 15:39:03 :: global dns servers are None None None
2009/08/15 15:39:03 :: domain is None
2009/08/15 15:39:03 :: search domain is None
2009/08/15 15:39:03 :: setting automatically reconnect when connection drops True
2009/08/15 15:39:03 :: Setting dhcp client to 0
2009/08/15 15:39:03 :: Wireless configuration file found...
2009/08/15 15:39:03 :: Wired configuration file found...
2009/08/15 15:39:03 :: chmoding configuration files 0600...
2009/08/15 15:39:03 :: chowning configuration files root:root...
2009/08/15 15:39:03 :: Using wireless interface...eth1
2009/08/15 15:39:03 :: Using wired interface...eth0
2009/08/15 15:39:10 :: Autoconnecting...
2009/08/15 15:39:13 :: Attempting to autoconnect with wired interface...
2009/08/15 15:39:13 :: Putting interface down
2009/08/15 15:39:13 :: Releasing DHCP leases...
2009/08/15 15:39:13 :: Setting false IP...
2009/08/15 15:39:13 :: Flushing the routing table...
2009/08/15 15:39:13 :: Putting interface up...
2009/08/15 15:39:13 :: Running DHCP
2009/08/15 15:39:13 :: dhcpcd: version 5.0.6 starting
2009/08/15 15:39:13 ::
2009/08/15 15:39:13 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 15:39:13 ::
2009/08/15 15:39:23 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 15:39:23 ::
2009/08/15 15:39:43 :: dhcpcd: timed out
2009/08/15 15:39:43 ::
2009/08/15 15:39:43 :: DHCP connection failed
2009/08/15 15:39:43 :: exiting connection thread
2009/08/15 15:39:45 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 15:39:45 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 15:39:45 :: Sending connection attempt result dhcp_failed
2009/08/15 15:41:46 :: Daemon going down, killing wicd-monitor...
2009/08/15 15:41:46 :: Removing PID file...
2009/08/15 15:41:46 :: Shutting down...
2009/08/15 15:42:33 :: ---------------------------
2009/08/15 15:42:33 :: wicd initializing...
2009/08/15 15:42:33 :: ---------------------------
2009/08/15 15:42:33 :: wicd is version 1.6.2 436
2009/08/15 15:42:33 :: setting backend to external
2009/08/15 15:42:33 :: trying to load backend external
2009/08/15 15:42:33 :: successfully loaded backend external
2009/08/15 15:42:33 :: trying to load backend external
2009/08/15 15:42:33 :: successfully loaded backend external
2009/08/15 15:42:33 :: Automatically detected wireless interface eth0
2009/08/15 15:42:33 :: setting wireless interface eth1
2009/08/15 15:42:33 :: automatically detected wired interface eth1
2009/08/15 15:42:33 :: setting wired interface eth0
2009/08/15 15:42:33 :: setting wpa driver wext
2009/08/15 15:42:33 :: setting use global dns to False
2009/08/15 15:42:33 :: setting global dns
2009/08/15 15:42:33 :: global dns servers are None None None
2009/08/15 15:42:33 :: domain is None
2009/08/15 15:42:33 :: search domain is None
2009/08/15 15:42:33 :: setting automatically reconnect when connection drops True
2009/08/15 15:42:33 :: Setting dhcp client to 0
2009/08/15 15:42:33 :: Wireless configuration file found...
2009/08/15 15:42:33 :: Wired configuration file found...
2009/08/15 15:42:33 :: chmoding configuration files 0600...
2009/08/15 15:42:33 :: chowning configuration files root:root...
2009/08/15 15:42:33 :: Using wireless interface...eth1
2009/08/15 15:42:33 :: Using wired interface...eth0
2009/08/15 15:42:39 :: Autoconnecting...
2009/08/15 15:42:42 :: Attempting to autoconnect with wired interface...
2009/08/15 15:42:42 :: Putting interface down
2009/08/15 15:42:42 :: Releasing DHCP leases...
2009/08/15 15:42:42 :: Setting false IP...
2009/08/15 15:42:42 :: Flushing the routing table...
2009/08/15 15:42:42 :: Putting interface up...
2009/08/15 15:42:42 :: Running DHCP
2009/08/15 15:42:42 :: dhcpcd: version 5.0.6 starting
2009/08/15 15:42:42 ::
2009/08/15 15:42:42 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 15:42:42 ::
2009/08/15 15:42:52 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 15:42:52 ::
2009/08/15 15:43:12 :: dhcpcd: timed out
2009/08/15 15:43:12 ::
2009/08/15 15:43:12 :: DHCP connection failed
2009/08/15 15:43:12 :: exiting connection thread
2009/08/15 15:43:14 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 15:43:14 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 15:43:14 :: Sending connection attempt result dhcp_failed
2009/08/15 15:44:27 :: Daemon going down, killing wicd-monitor...
2009/08/15 15:44:27 :: Removing PID file...
2009/08/15 15:44:27 :: Shutting down...
2009/08/15 15:44:48 :: ---------------------------
2009/08/15 15:44:48 :: wicd initializing...
2009/08/15 15:44:48 :: ---------------------------
2009/08/15 15:44:48 :: wicd is version 1.6.2 436
2009/08/15 15:44:48 :: setting backend to external
2009/08/15 15:44:48 :: trying to load backend external
2009/08/15 15:44:48 :: successfully loaded backend external
2009/08/15 15:44:48 :: trying to load backend external
2009/08/15 15:44:48 :: successfully loaded backend external
2009/08/15 15:44:48 :: Automatically detected wireless interface eth0
2009/08/15 15:44:48 :: setting wireless interface eth1
2009/08/15 15:44:48 :: automatically detected wired interface eth1
2009/08/15 15:44:48 :: setting wired interface eth0
2009/08/15 15:44:48 :: setting wpa driver wext
2009/08/15 15:44:48 :: setting use global dns to False
2009/08/15 15:44:48 :: setting global dns
2009/08/15 15:44:48 :: global dns servers are None None None
2009/08/15 15:44:48 :: domain is None
2009/08/15 15:44:48 :: search domain is None
2009/08/15 15:44:48 :: setting automatically reconnect when connection drops True
2009/08/15 15:44:48 :: Setting dhcp client to 0
2009/08/15 15:44:48 :: Wireless configuration file found...
2009/08/15 15:44:48 :: Wired configuration file found...
2009/08/15 15:44:48 :: chmoding configuration files 0600...
2009/08/15 15:44:48 :: chowning configuration files root:root...
2009/08/15 15:44:48 :: Using wireless interface...eth1
2009/08/15 15:44:48 :: Using wired interface...eth0
2009/08/15 15:44:58 :: trying to load backend ioctl
2009/08/15 15:44:58 :: WARNING: python-iwscan not found, falling back to using iwlist scan.
2009/08/15 15:44:58 :: WARNING: python-wpactrl not found, falling back to using wpa_cli.
2009/08/15 15:44:58 :: trying to load backend external
2009/08/15 15:45:57 :: Autoconnecting...
2009/08/15 15:45:57 :: Putting interface down
2009/08/15 15:45:57 :: Attempting to autoconnect with wired interface...
2009/08/15 15:45:57 :: Releasing DHCP leases...
2009/08/15 15:45:57 :: Setting false IP...
2009/08/15 15:45:57 :: Flushing the routing table...
2009/08/15 15:45:57 :: Putting interface up...
2009/08/15 15:45:57 :: Running DHCP
2009/08/15 15:45:57 :: dhcpcd: version 5.0.6 starting
2009/08/15 15:45:57 ::
2009/08/15 15:45:57 :: dhcpcd: eth0: rebinding lease of 192.168.0.193
2009/08/15 15:45:57 ::
2009/08/15 15:46:07 :: dhcpcd: eth0: broadcasting for a lease
2009/08/15 15:46:07 ::
2009/08/15 15:46:27 :: dhcpcd: timed out
2009/08/15 15:46:27 ::
2009/08/15 15:46:27 :: DHCP connection failed
2009/08/15 15:46:27 :: exiting connection thread
2009/08/15 15:46:29 :: No wired connection present, attempting to autoconnect to wireless network
2009/08/15 15:46:29 :: Unable to autoconnect, you'll have to manually connect
2009/08/15 15:46:29 :: Sending connection attempt result dhcp_failed

djszapi · 2009-08-16 07:42:09

Hello fowler!

Did you try it from console or with network manager, autowifi, etc. too ?
Did you try from console with dhclient instead of dhcpcd ?
Did you try with earlier dhcpcd/dhclient version too ?

fowler · 2009-08-16 12:48:46

From the console I ping www.pickawebsite.com and get nothing.
I don't have internet with arch so i can't try networkmanager, autowifi, etc.

What do you mean when you say did I try dhclient from the console versus dhcpcd?

fowler · 2009-08-19 01:16:52

bump

ngoonee · 2009-08-19 01:23:14

Try to do a manual connection, this is easiest on a LAN connection. Basically just bring the interface up with ifconfig eth0 up and then dhcpcd eth0.

Looks like DHCP timeouts to me.

fowler · 2009-08-19 21:50:06

I did it manually as stated above and dhcp does timeout... the question is why? I rebooted twice and no internet. I rebooted again within 10 minutes and now I have network (wired and wireless). It is consistently working in windows.

Sounds like this guy is having a similar issue. http://bbs.archlinux.org/viewtopic.php?id=78195

fowler · 2009-08-21 13:12:19

bump

fowler · 2009-08-24 13:34:06

Was able to boot this weekend and did an update which updated the kernel. Rebooted and there was no network. Rebooted again and no network... rebooted again and... had network!? I tried changing wicd to use dhclient only and did the triple reboot test again and it didn't change anything... randomly working network... same with dhcpcd.

So it appears to be a dhcp timeout issue however it makes no sense because before the update a couple weeks ago it was working every time with no hiccup. Am I not providing enough information that will aid in anyone helping me figure this out?

erno · 2009-08-24 19:47:23

This might not be true but I think i read somewhere that after suspending a wireless card in windows it might not activate properly in linux.

fowler · 2009-08-27 15:53:38

so I guess the solution based on your premise would be...?

I actually took out all the wicd stuff and did a default network setup based on the arch manual and I can bring up a wired connection... so I'm really starting to wonder if it's an wicd issue?

Arch Linux

#1 2009-08-15 20:36:25

Wired and Wireless sometimes work (mostly not) after update.

#2 2009-08-16 07:42:09

Re: Wired and Wireless sometimes work (mostly not) after update.

#3 2009-08-16 12:48:46

Re: Wired and Wireless sometimes work (mostly not) after update.

#4 2009-08-19 01:16:52

Re: Wired and Wireless sometimes work (mostly not) after update.

#5 2009-08-19 01:23:14

Re: Wired and Wireless sometimes work (mostly not) after update.

#6 2009-08-19 21:50:06

Re: Wired and Wireless sometimes work (mostly not) after update.

#7 2009-08-21 13:12:19

Re: Wired and Wireless sometimes work (mostly not) after update.

#8 2009-08-24 13:34:06

Re: Wired and Wireless sometimes work (mostly not) after update.

#9 2009-08-24 19:47:23

Re: Wired and Wireless sometimes work (mostly not) after update.

#10 2009-08-27 15:53:38

Re: Wired and Wireless sometimes work (mostly not) after update.

Board footer