ADSL Speedtouch USB 330 Help needed! [Fxd]

Shemeta · 2004-03-02 21:04:24

Hi Archers,

i have problems setting up my 330 Speedtouch USB ADSL modem. i have installed rp-pppoe, the speedtouch package from extra. i run modprobe usbnet & speedtch. i tried also the program from this site http://s1x.homelinux.net/downloads/spee … installer/ , but when i run pppd, i get an error that my kernel is built without PPP support. i am running AL's kernel-2.6.3 .
also hwd doesn't detect my modem. i don't have the module usbcore. i don't know if it's needed. are there other modules or drivers that i might need?

any help would be appreciated. thanks a lot.

Regards, Shemeta

Mr Green · 2004-03-03 08:59:02

Have you got libusb?

Does your system show modem connected (ie info center USB devices in KDE)?

I know this may not help you but I had the same modem in the end I stuck on Ebay & bought a router (Solwise SAR130) never looked back.....

Mr Green

Shemeta · 2004-03-03 09:01:24

So after loading all possible ppp* modules, i get the following output:

[root@myhost Speedtouchconf]# pppd call adsl
pppoe: ioctl(SIOCGIFHWADDR): Session 0: No such device
Couldn't get channel number: Input/output error
Using interface ppp0
Connect: ppp0 <--> /dev/pts/3
pppoe: ioctl(SIOCGIFHWADDR): Session 0: No such device
Modem hangup
Connection terminated.
pppoe: ioctl(SIOCGIFHWADDR): Session 0: No such device
Using interface ppp0
Connect: ppp0 <--> /dev/pts/3
Modem hangup
Connection terminated.
pppoe: ioctl(SIOCGIFHWADDR): Session 0: No such device
Using interface ppp0
Connect: ppp0 <--> /dev/pts/3
Modem hangup
Connection terminated.
pppoe: ioctl(SIOCGIFHWADDR): Session 0: No such device
Couldn't get channel number: Input/output error
pppoe: ioctl(SIOCGIFHWADDR): Session 0: No such device
Couldn't get channel number: Input/output error
pppoe: ioctl(SIOCGIFHWADDR): Session 0: No such device
Couldn't get channel number: Input/output error
pppoe: ioctl(SIOCGIFHWADDR): Session 0: No such device
Couldn't get channel number: Input/output error
Using interface ppp0
Connect: ppp0 <--> /dev/pts/3
pppoe: ioctl(SIOCGIFHWADDR): Session 0: No such device
Modem hangup
Connection terminated.
pppoe: ioctl(SIOCGIFHWADDR): Session 0: No such device
Couldn't get channel number: Input/output error
[root@myhost Speedtouchconf]#

i wonder what this means? any ideas? does my comp recognise my USB modem?

any help or suggestions are welcome!

Shemeta

Mr Green · 2004-03-03 09:08:27

As I say can you check if box can see modem....info-center or even pacman -S usbview

Shemeta · 2004-03-03 09:27:25

Hi Mr Green,

i have libusb installed. i am not using KDE, so i will install usbview & let you know what's going on.

thank you for your time.

Shemeta

Shemeta · 2004-03-03 09:51:05

usbview detects my modem at:

IHCI Host Controller
Speed Touch 330

& here is my /proc/bus/usb/devices :

T:  Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.3 uhci_hcd
S:  Product=UHCI Host Controller
S:  SerialNumber=0000:00:1d.1
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms

T:  Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#=  1 Spd=12  MxCh= 2
B:  Alloc=  0/900 us ( 0%), #Int=  0, #Iso=  0
D:  Ver= 1.10 Cls=09(hub  ) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 2.06
S:  Manufacturer=Linux 2.6.3 uhci_hcd
S:  Product=UHCI Host Controller
S:  SerialNumber=0000:00:1d.0
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=09(hub  ) Sub=00 Prot=00 Driver=hub
E:  Ad=81(I) Atr=03(Int.) MxPS=   2 Ivl=255ms

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=ff(vend.) Sub=00 Prot=00 MxPS= 8 #Cfgs=  1
P:  Vendor=06b9 ProdID=4061 Rev= 2.00
S:  Manufacturer=ALCATEL
S:  Product=Speed Touch 330 
S:  SerialNumber=0090D09825D8
C:* #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA
I:  If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=50ms
I:  If#= 1 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=00 Prot=00 Driver=speedtch
I:  If#= 1 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=speedtch
E:  Ad=06(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=87(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:  If#= 1 Alt= 2 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=speedtch
E:  Ad=06(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=87(I) Atr=01(Isoc) MxPS= 640 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=speedtch
E:  Ad=06(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=07(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=87(I) Atr=01(Isoc) MxPS= 960 Ivl=1ms
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=05(O) Atr=02(Bulk) MxPS=   8 Ivl=0ms
E:  Ad=85(I) Atr=02(Bulk) MxPS=   8 Ivl=0ms

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0d49 ProdID=3005 Rev= 1.00
S:  Manufacturer=Maxtor
S:  Product=3000LS v01.00.00
S:  SerialNumber=DEF106528F5E
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=88(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms

i loaded the modules usb-storage,sd_mod & speedtch.

hope this helps.

Shemeta

Mr Green · 2004-03-03 10:58:21

As I have said...I never got 330 working...so I may not be able to help more...someone maybe on the forum has got one that works...

Mr Green

Shemeta · 2004-03-03 14:51:18

well i guess we are the only one who have this modem, so i think i will go to LQ.org & see if i can get any help there.

See ya, Shemeta

Shemeta · 2004-03-04 14:12:56

Hola!

i finally figured it out with the help of Steve Parker, the maker of Speedtouchconf script. now i am online with my Speedtouch 330 USB ADSL modem. i hope he will fix his script. if not, you can contact me & i can email it to anybody. or i can upload the package somewhere,since i don't have any webspace yet. it is only for kernel-2.6.x & it works with the Speedtouch 330.

That's all folks, time to do pacman -Syu

Guest · 2004-03-05 10:05:42

hi Shemeta
can u write step by step procedure i am also facing the same problem
thankx

Shemeta · 2004-03-06 19:50:11

i can email you the everything as an attachment. just give me an email.

Guest · 2004-03-07 15:59:12

here is my email

khiska_hoowa@hotmail.com

Thankx in advance

sudman1 · 2005-02-18 01:54:44

I'd like a copy of the e-mail as well. You can post the content here, or e-mail me at james.sudbury@btinternet.com

Arch Linux

#1 2004-03-02 21:04:24

ADSL Speedtouch USB 330 Help needed! [Fxd]

#2 2004-03-03 08:59:02

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#3 2004-03-03 09:01:24

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#4 2004-03-03 09:08:27

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#5 2004-03-03 09:27:25

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#6 2004-03-03 09:51:05

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#7 2004-03-03 10:58:21

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#8 2004-03-03 14:51:18

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#9 2004-03-04 14:12:56

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#10 2004-03-05 10:05:42

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#11 2004-03-06 19:50:11

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#12 2004-03-07 15:59:12

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

#13 2005-02-18 01:54:44

Re: ADSL Speedtouch USB 330 Help needed! [Fxd]

Board footer