You are not logged in.

Pages: 1

#1 2010-07-11 05:38:56

unixNeophyte
Member
Registered: 2008-03-09
Posts: 26

Unable to burn a cd with k3b

This problem is new cause I burned 4 or 5 cd's 10 days ago.
I roll back to udev 158 and k3b-1.93.0rc4 but rolling back did not solve this problem.


This is the output with the burnfree feature enable

Devices
-----------------------
TSSTcorp CDDVDW SH-S223F SB03 (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump] [%7]

System
-----------------------
K3b Version: 2.0.0
KDE Version: 4.4.5 (KDE 4.4.5)
QT Version:  4.6.3
Kernel:      2.6.34-ARCH

Used versions
-----------------------
cdrecord: 1.1.10

cdrecord
-----------------------
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.10
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   : 
Vendor_info    : 'TSSTcorp'
Identification : 'CDDVDW SH-S223F '
Revision       : 'SB03'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x0015 (DVD-R/DL sequential recording) 
Profile: 0x0016 (DVD-R/DL layer jump recording) 
Profile: 0x0017 (Reserved/Unknown) 
Profile: 0x002B (DVD+R/DL) 
Profile: 0x001B (DVD+R) 
Profile: 0x001A (DVD+RW) 
Profile: 0x0014 (DVD-RW sequential recording) 
Profile: 0x0013 (DVD-RW restricted overwrite) 
Profile: 0x0012 (DVD-RAM) 
Profile: 0x0011 (DVD-R sequential recording) 
Profile: 0x0010 (DVD-ROM) 
Profile: 0x000A (CD-RW) 
Profile: 0x0009 (CD-R) (current)
Profile: 0x0008 (CD-ROM) 
Profile: 0x0002 (Removable disk) 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1962752 = 1916 KB
FIFO size      : 4194304 = 4096 KB
Speed set to 7056 KB/s
Track 01: data   340 MB        
Total size:      390 MB (38:41.06) = 174080 sectors
Lout start:      390 MB (38:43/05) = 174080 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 4
  Is unrestricted
  Is not erasable
  Disk sub type: Medium Type A, low Beta category (A-) (2)
  ATIP start of lead in:  -11634 (97:26/66)
  ATIP start of lead out: 359849 (79:59/74)
Disk type:    Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 185769
Starting to write CD/DVD at speed  40.0 in real SAO mode for single session.
Last chance to quit, starting real write in    2 seconds.
   1 seconds.
   0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Sending CUE sheet...
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 FF FF FF 6A 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 72 0B 00 00 00 00 00 0E 09 0C 00 00 00 03 00 00
Sense Key: 0x0 No Additional Sense, Segment 11
Sense Code: 0x00 Qual 0x03 (setmark detected) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.699s timeout 200s
Writing pregap for track 1 at -150
write track pad data: error after 0 bytes
BFree: 0 K BSize: 1916 K
Starting new track at sector: 0
Track 01:    0 of  340 MB written.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 00 00 00 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 21 02 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.004s timeout 200s
/usr/bin/wodim: The current problem looks like a buffer underrun.
/usr/bin/wodim: I[b]t looks like 'driveropts=burnfree' does not work for this drive[/b].
/usr/bin/wodim: Please report.
/usr/bin/wodim: Make sure that you are root, enable DMA and check your HW/OS set up.
write track data: error after 0 bytes
Writing  time:   16.278s
Average write speed 406.8x.
Fixating...
Fixating time:    0.002s
/usr/bin/wodim: fifo had 64 puts and 1 gets.
/usr/bin/wodim: fifo was 0 times empty and 0 times full, min fill was 100%.
BURN-Free was never needed.

cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/sr0 speed=40 -sao driveropts=burnfree -overburn -data -tsize=174080s -

And this with burnfree disabled

Devices
-----------------------
TSSTcorp CDDVDW SH-S223F SB03 (/dev/sr0, CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL) [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump] [%7]

System
-----------------------
K3b Version: 2.0.0
KDE Version: 4.4.5 (KDE 4.4.5)
QT Version:  4.6.3
Kernel:      2.6.34-ARCH

Used versions
-----------------------
cdrecord: 1.1.10

cdrecord
-----------------------
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.10
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   : 
Vendor_info    : 'TSSTcorp'
Identification : 'CDDVDW SH-S223F '
Revision       : 'SB03'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x0015 (DVD-R/DL sequential recording) 
Profile: 0x0016 (DVD-R/DL layer jump recording) 
Profile: 0x0017 (Reserved/Unknown) 
Profile: 0x002B (DVD+R/DL) 
Profile: 0x001B (DVD+R) 
Profile: 0x001A (DVD+RW) 
Profile: 0x0014 (DVD-RW sequential recording) 
Profile: 0x0013 (DVD-RW restricted overwrite) 
Profile: 0x0012 (DVD-RAM) 
Profile: 0x0011 (DVD-R sequential recording) 
Profile: 0x0010 (DVD-ROM) 
Profile: 0x000A (CD-RW) 
Profile: 0x0009 (CD-R) (current)
Profile: 0x0008 (CD-ROM) 
Profile: 0x0002 (Removable disk) 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1962752 = 1916 KB
FIFO size      : 4194304 = 4096 KB
Speed set to 7056 KB/s
Track 01: data   696 MB        
Total size:      799 MB (79:11.36) = 356352 sectors
Lout start:      799 MB (79:13/27) = 356352 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 4
  Is unrestricted
  Is not erasable
  Disk sub type: Medium Type A, low Beta category (A-) (2)
  ATIP start of lead in:  -11634 (97:26/66)
  ATIP start of lead out: 359849 (79:59/74)
Disk type:    Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359849 Blocks current: 359849 Blocks remaining: 3497
Starting to write CD/DVD at speed  40.0 in real SAO mode for single session.
Last chance to quit, starting real write in    2 seconds.
   1 seconds.
   0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Sending CUE sheet...
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 FF FF FF 6A 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 72 0B 00 00 00 00 00 0E 09 0C 00 00 00 03 00 00
Sense Key: 0x0 No Additional Sense, Segment 11
Sense Code: 0x00 Qual 0x03 (setmark detected) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.700s timeout 200s
Writing pregap for track 1 at -150
write track pad data: error after 0 bytes
BFree: 0 K BSize: 1916 K
Starting new track at sector: 0
Track 01:    0 of  696 MB written.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 00 00 00 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 21 02 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.002s timeout 200s
/usr/bin/wodim: The current problem looks like a buffer underrun.
/usr/bin/wodim: It looks like 'driveropts=burnfree' does not work for this drive.
/usr/bin/wodim: Please report.
/usr/bin/wodim: Make sure that you are root, enable DMA and check your HW/OS set up.
write track data: error after 0 bytes
Writing  time:   16.309s
Average write speed 832.4x.
Fixating...
Fixating time:    0.641s
/usr/bin/wodim: fifo had 64 puts and 1 gets.
/usr/bin/wodim: fifo was 0 times empty and 0 times full, min fill was 100%.
BURN-Free was never needed.

cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/sr0 speed=40 -sao -overburn -data -tsize=356352s -

Any help will be higly appreciated

Offline

#2 2010-07-11 06:11:50

Anonymo
Member
Registered: 2005-04-07
Posts: 427
Website

Re: Unable to burn a cd with k3b

I have the same problem, creates coasters that the OS doesn't even recognize a CD is in the drive and everything starts lagging when you try to mount the drive manually.  I see the cd light reading the cd, but nothing.  Never had a problem with xfburn.

Offline

#3 2010-07-11 06:32:25

jasonwryan
Anarchist
From: .nz
Registered: 2009-05-09
Posts: 30,424
Website

Re: Unable to burn a cd with k3b

I had a similar issue last weekend - but with a different error on a debian machine (so may not be applicable):

wodim: OPC failed

I eventually used crdrecord and it worked fine...

Arch + dwm   •   Mercurial repos  •   Surfraw

Registered Linux User #482438

Offline

Pages: 1

Board footer

Powered by FluxBB