You are not logged in.
Pages: 1
Hi ,
Am new to Arch linux and just completed install it on my system, but after installing Kde and reboot, am unable to run "startx" command :
this in the /var/log/xorg.0.log file contents : http://paste.pocoo.org/show/372237/
/var/log/xorg.0.log.old file contents : http://paste.pocoo.org/show/372238/
~/.xinitrc file contents : http://paste.pocoo.org/show/378834/
Thanx in advance ....>
Offline
What video card do you have?
xfce | compiz | gmrun | urxvt | chromium | geany | aqualung | vlc | geeqie
Offline
Your first link above is a bunch of rapidshare URLs - so not much help. There is a very clear error in the old X log concerning the nouveau kernel module - that should be easy to investigate.
Offline
Please post the output of this command:
lspci
Last edited by stefanwilkens (2011-04-27 08:18:55)
Arch i686 on Phenom X4 | GTX760
Offline
sorry about the link ..... @Korrode this is what i got from lspce -v : VGA compatible controller: Intel Corporation 4 Series Chipset Integrated
already loaded i915 kernel module ...
Offline
@stefanwilkens :
this is the output i got from lspci :
[deephands@system ~]$ lspci
00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03)
00:02.0 VGA compatible controller: Intel Corporation 4 Series Chipset Integrated Graphics Controller (rev 03)
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation N10/ICH 7 Family PCI Express Port 2 (rev 01)
00:1d.0 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation N10/ICH7 Family SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation N10/ICH 7 Family SMBus Controller (rev 01)
02:00.0 Ethernet controller: Atheros Communications AR8151 v1.0 Gigabit Ethernet (rev c0)
Offline
/var/log/xorg.0.log.old is from gentoo, not arch.
and in .xinitrc replace
twm &
xclock -geometry 50x50-1+1 &
xterm -geometry 80x50+494+51 &
xterm -geometry 80x20+494-0 &
exec xterm -geometry 80x66+0+0 -name login
exec ck-launch-session startkde
with just:
exec ck-launch-session startkde
xf86-video-intel is installed on your system?
pacman -Q xf86-video-intel to check.
Arch64/DWM || My Dropbox referral link
Offline
output for : pacman -Q xf86-video-intel
xf86-video-intel 2.15.0-1
also tried removing extra lines .... no changes observed ...>
Offline
can you provide the xorg log file? the one from using ARCH this time please.
Arch64/DWM || My Dropbox referral link
Offline
@ JokerBoy ... xorg log file /var/log/Xorg.0.log
: http://paste.pocoo.org/show/378928/
Offline
Pages: 1