You are not logged in.

#1 2021-11-21 20:17:39

quellen
Member
Registered: 2014-05-24
Posts: 204

how read S.M.A.R.T. hdd log

hello,
i took a SMART test on an old hdd and it says these errors:

smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.73-1-lts] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.10
Device Model:     ST3250620AS
Serial Number:    CENSURED
Firmware Version: 3.AAD
User Capacity:    250,059,350,016 bytes [250 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7 (minor revision not indicated)
Local Time is:    Sun Nov 21 21:04:25 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  430) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (  92) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   117   088   006    -    127355810
  3 Spin_Up_Time            PO----   095   095   000    -    0
  4 Start_Stop_Count        -O--CK   097   097   020    -    3827
  5 Reallocated_Sector_Ct   PO--CK   100   100   036    -    0
  7 Seek_Error_Rate         POSR--   066   060   030    -    558828125754
  9 Power_On_Hours          -O--CK   079   079   000    -    18605
 10 Spin_Retry_Count        PO--C-   100   100   097    -    0
 12 Power_Cycle_Count       -O--CK   096   096   020    -    4151
187 Reported_Uncorrect      -O--CK   086   086   000    -    14
189 High_Fly_Writes         -O-RCK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   068   044   045    Past 32 (Min/Max 29/32)
194 Temperature_Celsius     -O---K   032   056   000    -    32 (0 12 0 0 0)
195 Hardware_ECC_Recovered  -O-RC-   064   051   000    -    14800472
197 Current_Pending_Sector  -O--C-   100   100   000    -    0
198 Offline_Uncorrectable   ----C-   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ------   100   253   000    -    0
202 Data_Address_Mark_Errs  -O--CK   100   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01       GPL,SL  R/O      1  Summary SMART error log
0x02       GPL,SL  R/O      5  Comprehensive SMART error log
0x03       GPL,SL  R/O      5  Ext. Comprehensive SMART error log
0x06       GPL,SL  R/O      1  SMART self-test log
0x07       GPL,SL  R/O      1  Extended self-test log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL,SL  R/O      1  NCQ Command Error log
0x11       GPL,SL  R/O      1  SATA Phy Event Counters log
0x20       GPL,SL  R/O      1  Streaming performance log [OBS-8]
0x21       GPL,SL  R/O      1  Write stream error log
0x22       GPL,SL  R/O      1  Read stream error log
0x23       GPL,SL  R/O      1  Delayed sector log [OBS-8]
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0       GPL,SL  VS       1  Device vendor specific log
0xa1       GPL,SL  VS      20  Device vendor specific log
0xa2       GPL,SL  VS     101  Device vendor specific log
0xa8       GPL,SL  VS      20  Device vendor specific log
0xa9       GPL,SL  VS       1  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer
0xff       GPL     -    23040  Reserved

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 14
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 14 [13] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:37.809  READ DMA EXT
  25 00 00 00 08 00 02 f9 00 0d d7 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 08 00 00 15 00 60 77 e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 18 00 00 f1 00 5f 17 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 79 00 94 f7 e0 00     00:02:35.315  READ DMA EXT

Error 13 [12] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 80 00 06 1a 00 9e 97 e0 00     00:02:35.217  READ DMA EXT
  25 00 00 00 40 00 02 f9 00 0d 97 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 38 00 00 f0 00 5f df e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 08 00 00 6d 00 08 c7 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 1a 00 9d 91 e0 00     00:02:35.315  READ DMA EXT

Error 12 [11] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 68 00 06 1a 00 9e af e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 00 00 5e 3f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 20 00 1c 06 00 9b 7b e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:41.785  READ DMA EXT

Error 11 [10] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 f1 00 5f 2f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:35.315  READ DMA EXT
  35 00 00 00 08 00 1c 37 00 90 5f e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:35.315  READ DMA EXT

Error 10 [9] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:37.809  READ DMA EXT
  25 00 00 00 08 00 02 f9 00 0d d7 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 08 00 00 15 00 60 77 e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 18 00 00 f1 00 5f 17 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 79 00 94 f7 e0 00     00:02:35.315  READ DMA EXT

Error 9 [8] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 80 00 06 1a 00 9e 97 e0 00     00:02:35.217  READ DMA EXT
  25 00 00 00 40 00 02 f9 00 0d 97 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 38 00 00 f0 00 5f df e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 08 00 00 6d 00 08 c7 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 1a 00 9d 91 e0 00     00:02:35.315  READ DMA EXT

Error 8 [7] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 68 00 06 1a 00 9e af e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 00 00 5e 3f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 20 00 1c 06 00 9b 7b e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:41.785  READ DMA EXT

Error 7 [6] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 f1 00 5f 2f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:35.315  READ DMA EXT
  35 00 00 00 08 00 1c 37 00 90 5f e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:35.315  READ DMA EXT

Error 6 [5] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:37.809  READ DMA EXT
  25 00 00 00 08 00 02 f9 00 0d d7 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 08 00 00 15 00 60 77 e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 18 00 00 f1 00 5f 17 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 79 00 94 f7 e0 00     00:02:35.315  READ DMA EXT

Error 5 [4] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 80 00 06 1a 00 9e 97 e0 00     00:02:35.217  READ DMA EXT
  25 00 00 00 40 00 02 f9 00 0d 97 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 38 00 00 f0 00 5f df e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 08 00 00 6d 00 08 c7 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 1a 00 9d 91 e0 00     00:02:35.315  READ DMA EXT

Error 4 [3] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 68 00 06 1a 00 9e af e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 00 00 5e 3f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 20 00 1c 06 00 9b 7b e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:41.785  READ DMA EXT

Error 3 [2] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 f1 00 5f 2f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:35.315  READ DMA EXT
  35 00 00 00 08 00 1c 37 00 90 5f e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:35.315  READ DMA EXT

Error 2 [1] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:37.809  READ DMA EXT
  25 00 00 00 08 00 02 f9 00 0d d7 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 08 00 00 15 00 60 77 e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 18 00 00 f1 00 5f 17 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 79 00 94 f7 e0 00     00:02:35.315  READ DMA EXT

Error 1 [0] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 80 00 06 1a 00 9e 97 e0 00     00:02:35.217  READ DMA EXT
  25 00 00 00 40 00 02 f9 00 0d 97 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 38 00 00 f0 00 5f df e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 08 00 00 6d 00 08 c7 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 1a 00 9d 91 e0 00     00:02:35.315  READ DMA EXT

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%     18605         -
# 2  Short offline       Completed without error       00%     18604         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Commands not supported

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2            2  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS

What's written? is the hard drive going to die?

Last edited by quellen (2021-11-21 20:17:58)

Offline

#2 2021-11-21 21:17:17

seth
Member
Registered: 2012-09-03
Posts: 25,010

Re: how read S.M.A.R.T. hdd log

9 Power_On_Hours          -O--CK   079   079   000    -    18605
Error 14 [13] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)

18605 - 10703 = ?
There was a singular incident that lead to a couple of uncorrectable IO errors on a single block… how many power-on hours ago?
There're no reallocated or pending or offline uncorrectable errors - there's no indication that the drive will fail in the immediate future.

The IO errors could have been for weakend polarization or a drop of current (so the firmware continued to work but the discs didn't) or … anything. But even on 24/7 that was ~11 months ago.

Offline

#3 2021-11-24 14:42:54

quellen
Member
Registered: 2014-05-24
Posts: 204

Re: how read S.M.A.R.T. hdd log

Thank you.
however the hard disk is very noisy, especially during Windows startup.  I think it will die soon.

Offline

#4 2021-11-24 15:13:52

seth
Member
Registered: 2012-09-03
Posts: 25,010

Re: how read S.M.A.R.T. hdd log

You could run a full test or badblocks, but "noisy" itself isn't necessarily indicative of imminent failure. Eg. if the windows partition is highly fragmented the head will travel around a lot.
Another aspect contributing to noise is bad seating, loose screws, stuff like that that causes vibrations (to be carried on)

Offline

#5 2021-11-24 23:27:57

xerxes_
Member
Registered: 2018-04-29
Posts: 388

Re: how read S.M.A.R.T. hdd log

Go for smartctl extend (long) hdd test by 'smartctl -t long /dev/sdX'.

Offline

#6 2021-11-25 10:07:32

quellen
Member
Registered: 2014-05-24
Posts: 204

Re: how read S.M.A.R.T. hdd log

xerxes_ wrote:

Go for smartctl extend (long) hdd test by 'smartctl -t long /dev/sdX'.

done. it says: "Completed without error".

gsmartcontrol log:

smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.73-1-lts] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.10
Device Model:     ST3250620AS
Serial Number:    CENSURED
Firmware Version: 3.AAD
User Capacity:    250,059,350,016 bytes [250 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7 (minor revision not indicated)
Local Time is:    Thu Nov 25 10:58:59 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is:   Unavailable
APM feature is:   Unavailable
Rd look-ahead is: Enabled
Write cache is:   Enabled
DSN feature is:   Unavailable
ATA Security is:  Disabled, frozen [SEC2]

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  430) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (  92) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAGS    VALUE WORST THRESH FAIL RAW_VALUE
  1 Raw_Read_Error_Rate     POSR--   117   088   006    -    165929700
  3 Spin_Up_Time            PO----   095   095   000    -    0
  4 Start_Stop_Count        -O--CK   097   097   020    -    3842
  5 Reallocated_Sector_Ct   PO--CK   100   100   036    -    0
  7 Seek_Error_Rate         POSR--   065   060   030    -    773578043144
  9 Power_On_Hours          -O--CK   079   079   000    -    18622
 10 Spin_Retry_Count        PO--C-   100   100   097    -    0
 12 Power_Cycle_Count       -O--CK   096   096   020    -    4166
187 Reported_Uncorrect      -O--CK   086   086   000    -    14
189 High_Fly_Writes         -O-RCK   100   100   000    -    0
190 Airflow_Temperature_Cel -O---K   061   044   045    Past 39 (Min/Max 23/39)
194 Temperature_Celsius     -O---K   039   056   000    -    39 (0 12 0 0 0)
195 Hardware_ECC_Recovered  -O-RC-   059   051   000    -    172786765
197 Current_Pending_Sector  -O--C-   100   100   000    -    0
198 Offline_Uncorrectable   ----C-   100   100   000    -    0
199 UDMA_CRC_Error_Count    -OSRCK   200   200   000    -    0
200 Multi_Zone_Error_Rate   ------   100   253   000    -    0
202 Data_Address_Mark_Errs  -O--CK   100   253   000    -    0
                            ||||||_ K auto-keep
                            |||||__ C event count
                            ||||___ R error rate
                            |||____ S speed/performance
                            ||_____ O updated online
                            |______ P prefailure warning

General Purpose Log Directory Version 1
SMART           Log Directory Version 1 [multi-sector log support]
Address    Access  R/W   Size  Description
0x00       GPL,SL  R/O      1  Log Directory
0x01       GPL,SL  R/O      1  Summary SMART error log
0x02       GPL,SL  R/O      5  Comprehensive SMART error log
0x03       GPL,SL  R/O      5  Ext. Comprehensive SMART error log
0x06       GPL,SL  R/O      1  SMART self-test log
0x07       GPL,SL  R/O      1  Extended self-test log
0x09       GPL,SL  R/W      1  Selective self-test log
0x10       GPL,SL  R/O      1  NCQ Command Error log
0x11       GPL,SL  R/O      1  SATA Phy Event Counters log
0x20       GPL,SL  R/O      1  Streaming performance log [OBS-8]
0x21       GPL,SL  R/O      1  Write stream error log
0x22       GPL,SL  R/O      1  Read stream error log
0x23       GPL,SL  R/O      1  Delayed sector log [OBS-8]
0x80-0x9f  GPL,SL  R/W     16  Host vendor specific log
0xa0       GPL,SL  VS       1  Device vendor specific log
0xa1       GPL,SL  VS      20  Device vendor specific log
0xa2       GPL,SL  VS     101  Device vendor specific log
0xa8       GPL,SL  VS      20  Device vendor specific log
0xa9       GPL,SL  VS       1  Device vendor specific log
0xe0       GPL,SL  R/W      1  SCT Command/Status
0xe1       GPL,SL  R/W      1  SCT Data Transfer
0xff       GPL     -    23040  Reserved

SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 14
	CR     = Command Register
	FEATR  = Features Register
	COUNT  = Count (was: Sector Count) Register
	LBA_48 = Upper bytes of LBA High/Mid/Low Registers ]  ATA-8
	LH     = LBA High (was: Cylinder High) Register    ]   LBA
	LM     = LBA Mid (was: Cylinder Low) Register      ] Register
	LL     = LBA Low (was: Sector Number) Register     ]
	DV     = Device (was: Device/Head) Register
	DC     = Device Control Register
	ER     = Error register
	ST     = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 14 [13] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:37.809  READ DMA EXT
  25 00 00 00 08 00 02 f9 00 0d d7 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 08 00 00 15 00 60 77 e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 18 00 00 f1 00 5f 17 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 79 00 94 f7 e0 00     00:02:35.315  READ DMA EXT

Error 13 [12] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 80 00 06 1a 00 9e 97 e0 00     00:02:35.217  READ DMA EXT
  25 00 00 00 40 00 02 f9 00 0d 97 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 38 00 00 f0 00 5f df e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 08 00 00 6d 00 08 c7 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 1a 00 9d 91 e0 00     00:02:35.315  READ DMA EXT

Error 12 [11] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 68 00 06 1a 00 9e af e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 00 00 5e 3f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 20 00 1c 06 00 9b 7b e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:41.785  READ DMA EXT

Error 11 [10] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 f1 00 5f 2f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:35.315  READ DMA EXT
  35 00 00 00 08 00 1c 37 00 90 5f e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:35.315  READ DMA EXT

Error 10 [9] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:37.809  READ DMA EXT
  25 00 00 00 08 00 02 f9 00 0d d7 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 08 00 00 15 00 60 77 e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 18 00 00 f1 00 5f 17 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 79 00 94 f7 e0 00     00:02:35.315  READ DMA EXT

Error 9 [8] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 80 00 06 1a 00 9e 97 e0 00     00:02:35.217  READ DMA EXT
  25 00 00 00 40 00 02 f9 00 0d 97 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 38 00 00 f0 00 5f df e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 08 00 00 6d 00 08 c7 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 1a 00 9d 91 e0 00     00:02:35.315  READ DMA EXT

Error 8 [7] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 68 00 06 1a 00 9e af e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 00 00 5e 3f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 20 00 1c 06 00 9b 7b e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:41.785  READ DMA EXT

Error 7 [6] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 f1 00 5f 2f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:35.315  READ DMA EXT
  35 00 00 00 08 00 1c 37 00 90 5f e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:35.315  READ DMA EXT

Error 6 [5] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:37.809  READ DMA EXT
  25 00 00 00 08 00 02 f9 00 0d d7 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 08 00 00 15 00 60 77 e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 18 00 00 f1 00 5f 17 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 79 00 94 f7 e0 00     00:02:35.315  READ DMA EXT

Error 5 [4] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 80 00 06 1a 00 9e 97 e0 00     00:02:35.217  READ DMA EXT
  25 00 00 00 40 00 02 f9 00 0d 97 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 38 00 00 f0 00 5f df e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 08 00 00 6d 00 08 c7 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 1a 00 9d 91 e0 00     00:02:35.315  READ DMA EXT

Error 4 [3] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 68 00 06 1a 00 9e af e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 00 00 5e 3f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 20 00 1c 06 00 9b 7b e0 00     00:02:41.805  READ DMA EXT
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:41.785  READ DMA EXT

Error 3 [2] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 70 00 06 1a 00 9e a7 e0 00     00:02:37.809  READ DMA EXT
  35 00 00 00 08 00 00 f1 00 5f 2f e0 00     00:02:35.332  WRITE DMA EXT
  25 00 00 00 01 00 00 00 00 00 00 e0 00     00:02:35.315  READ DMA EXT
  35 00 00 00 08 00 1c 37 00 90 5f e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:35.315  READ DMA EXT

Error 2 [1] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 78 00 06 1a 00 9e 9f e0 00     00:02:37.809  READ DMA EXT
  25 00 00 00 08 00 02 f9 00 0d d7 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 08 00 00 15 00 60 77 e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 18 00 00 f1 00 5f 17 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 79 00 94 f7 e0 00     00:02:35.315  READ DMA EXT

Error 1 [0] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER -- ST COUNT  LBA_48  LH LM LL DV DC
  -- -- -- == -- == == == -- -- -- -- --
  40 -- 51 00 00 00 06 1a f6 9e f6 e0 00  Error: UNC at LBA = 0x61af69ef6 = 26222173942

  Commands leading to the command that caused the error were:
  CR FEATR COUNT  LBA_48  LH LM LL DV DC  Powered_Up_Time  Command/Feature_Name
  -- == -- == -- == == == -- -- -- -- --  ---------------  --------------------
  25 00 00 00 80 00 06 1a 00 9e 97 e0 00     00:02:35.217  READ DMA EXT
  25 00 00 00 40 00 02 f9 00 0d 97 e0 00     00:02:35.332  READ DMA EXT
  35 00 00 00 38 00 00 f0 00 5f df e0 00     00:02:35.315  WRITE DMA EXT
  35 00 00 00 08 00 00 6d 00 08 c7 e0 00     00:02:35.315  WRITE DMA EXT
  25 00 00 00 08 00 1c 1a 00 9d 91 e0 00     00:02:35.315  READ DMA EXT

SMART Extended Self-test Log Version: 1 (1 sectors)
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     18622         -
# 2  Short offline       Completed without error       00%     18605         -
# 3  Short offline       Completed without error       00%     18604         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

SCT Commands not supported

Device Statistics (GP/SMART Log 0x04) not supported

SATA Phy Event Counters (GP Log 0x11)
ID      Size     Value  Description
0x000a  2            2  Device-to-host register FISes sent due to a COMRESET
0x0001  2            0  Command failed due to ICRC error
0x0003  2            0  R_ERR response for device-to-host data FIS
0x0004  2            0  R_ERR response for host-to-device data FIS
0x0006  2            0  R_ERR response for device-to-host non-data FIS
0x0007  2            0  R_ERR response for host-to-device non-data FIS
$ sudo smartctl -a /dev/sdb
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.73-1-lts] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate Barracuda 7200.10
Device Model:     ST3250620AS
Serial Number:    CENSURED
Firmware Version: 3.AAD
User Capacity:    250.059.350.016 bytes [250 GB]
Sector Size:      512 bytes logical/physical
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA/ATAPI-7 (minor revision not indicated)
Local Time is:    Thu Nov 25 11:12:19 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		(  430) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (  92) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   117   088   006    Pre-fail  Always       -       165929700
  3 Spin_Up_Time            0x0003   095   095   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   097   097   020    Old_age   Always       -       3842
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   065   060   030    Pre-fail  Always       -       773578043236
  9 Power_On_Hours          0x0032   079   079   000    Old_age   Always       -       18622
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   096   096   020    Old_age   Always       -       4166
187 Reported_Uncorrect      0x0032   086   086   000    Old_age   Always       -       14
189 High_Fly_Writes         0x003a   100   100   000    Old_age   Always       -       0
190 Airflow_Temperature_Cel 0x0022   064   044   045    Old_age   Always   In_the_past 36 (Min/Max 23/39)
194 Temperature_Celsius     0x0022   036   056   000    Old_age   Always       -       36 (0 12 0 0 0)
195 Hardware_ECC_Recovered  0x001a   059   051   000    Old_age   Always       -       172792457
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 Data_Address_Mark_Errs  0x0032   100   253   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 14 (device log contains only the most recent five errors)
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 14 occurred at disk power-on lifetime: 18552 hours (773 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 58 0d fe e0  Error: UNC at LBA = 0x00fe0d58 = 16649560

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 01 58 0d fe e0 00      01:10:41.410  READ DMA EXT
  25 00 01 57 0d fe e0 00      01:10:41.410  READ DMA EXT
  25 00 01 56 0d fe e0 00      01:10:41.410  READ DMA EXT
  25 00 01 55 0d fe e0 00      01:10:41.410  READ DMA EXT
  25 00 01 54 0d fe e0 00      01:10:41.410  READ DMA EXT

Error 13 occurred at disk power-on lifetime: 18552 hours (773 days + 0 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 58 0d fe e0  Error: UNC at LBA = 0x00fe0d58 = 16649560

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 c0 20 0d fe e0 00      01:10:38.822  READ DMA EXT
  25 00 b6 80 84 d5 e0 00      01:10:38.821  READ DMA EXT
  25 00 00 80 83 d5 e0 00      01:10:38.815  READ DMA EXT
  35 00 16 30 08 d8 e0 00      01:10:38.812  WRITE DMA EXT
  35 00 00 30 07 d8 e0 00      01:10:38.811  WRITE DMA EXT

Error 12 occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 f6 1a 9e e0  Error: UNC at LBA = 0x009e1af6 = 10361590

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 28 ef 1a 9e e0 00      00:02:51.767  READ DMA EXT
  35 00 08 47 00 5e e0 00      00:02:51.767  WRITE DMA EXT
  25 00 30 e7 1a 9e e0 00      00:02:51.767  READ DMA EXT
  35 00 10 97 a0 61 e0 00      00:02:51.743  WRITE DMA EXT
  35 00 20 57 f1 5f e0 00      00:02:57.700  WRITE DMA EXT

Error 11 occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 f6 1a 9e e0  Error: UNC at LBA = 0x009e1af6 = 10361590

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 30 e7 1a 9e e0 00      00:02:51.767  READ DMA EXT
  35 00 10 97 a0 61 e0 00      00:02:51.767  WRITE DMA EXT
  35 00 20 57 f1 5f e0 00      00:02:51.767  WRITE DMA EXT
  25 00 01 00 00 00 e0 00      00:02:51.743  READ DMA EXT
  25 00 40 c1 e2 91 e0 00      00:02:51.726  READ DMA EXT

Error 10 occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 f6 1a 9e e0  Error: UNC at LBA = 0x009e1af6 = 10361590

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  25 00 38 df 1a 9e e0 00      00:02:51.767  READ DMA EXT
  35 00 08 47 9b 61 e0 00      00:02:51.767  WRITE DMA EXT
  25 00 10 01 d2 8e e0 00      00:02:51.767  READ DMA EXT
  35 00 08 3f 3e 8e e0 00      00:02:51.743  WRITE DMA EXT
  25 00 40 d7 1a 9e e0 00      00:02:51.726  READ DMA EXT

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     18622         -
# 2  Short offline       Completed without error       00%     18605         -
# 3  Short offline       Completed without error       00%     18604         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

I also defragmented from Windows 10 and after only 5 minutes it says "OK, 0% defragmented"

Last edited by quellen (2021-11-25 10:40:09)

Offline

#7 2021-11-25 14:35:08

seth
Member
Registered: 2012-09-03
Posts: 25,010

Re: how read S.M.A.R.T. hdd log

Test passed fine and there're still not more errors - your disk looks healthy…
(The barracudas rest their heads with a somewhat fearsome tchiiinnnng sound when idling - that's normal)

Offline

Board footer

Powered by FluxBB