You are not logged in.
Pages: 1
hello,
i took a SMART test on an old hdd and it says these errors:
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.73-1-lts] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10
Device Model: ST3250620AS
Serial Number: CENSURED
Firmware Version: 3.AAD
User Capacity: 250,059,350,016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Sun Nov 21 21:04:25 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 117 088 006 - 127355810
3 Spin_Up_Time PO---- 095 095 000 - 0
4 Start_Stop_Count -O--CK 097 097 020 - 3827
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
7 Seek_Error_Rate POSR-- 066 060 030 - 558828125754
9 Power_On_Hours -O--CK 079 079 000 - 18605
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 096 096 020 - 4151
187 Reported_Uncorrect -O--CK 086 086 000 - 14
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 068 044 045 Past 32 (Min/Max 29/32)
194 Temperature_Celsius -O---K 032 056 000 - 32 (0 12 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 064 051 000 - 14800472
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
200 Multi_Zone_Error_Rate ------ 100 253 000 - 0
202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 NCQ Command Error log
0x11 GPL,SL R/O 1 SATA Phy Event Counters log
0x20 GPL,SL R/O 1 Streaming performance log [OBS-8]
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x23 GPL,SL R/O 1 Delayed sector log [OBS-8]
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0 GPL,SL VS 1 Device vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL,SL VS 101 Device vendor specific log
0xa8 GPL,SL VS 20 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
0xff GPL - 23040 Reserved
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 14
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 14 [13] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:37.809 READ DMA EXT
25 00 00 00 08 00 02 f9 00 0d d7 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 08 00 00 15 00 60 77 e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 18 00 00 f1 00 5f 17 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 79 00 94 f7 e0 00 00:02:35.315 READ DMA EXT
Error 13 [12] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 80 00 06 1a 00 9e 97 e0 00 00:02:35.217 READ DMA EXT
25 00 00 00 40 00 02 f9 00 0d 97 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 38 00 00 f0 00 5f df e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 08 00 00 6d 00 08 c7 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 1a 00 9d 91 e0 00 00:02:35.315 READ DMA EXT
Error 12 [11] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 68 00 06 1a 00 9e af e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 00 00 5e 3f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 20 00 1c 06 00 9b 7b e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:41.785 READ DMA EXT
Error 11 [10] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 f1 00 5f 2f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:35.315 READ DMA EXT
35 00 00 00 08 00 1c 37 00 90 5f e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:35.315 READ DMA EXT
Error 10 [9] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:37.809 READ DMA EXT
25 00 00 00 08 00 02 f9 00 0d d7 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 08 00 00 15 00 60 77 e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 18 00 00 f1 00 5f 17 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 79 00 94 f7 e0 00 00:02:35.315 READ DMA EXT
Error 9 [8] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 80 00 06 1a 00 9e 97 e0 00 00:02:35.217 READ DMA EXT
25 00 00 00 40 00 02 f9 00 0d 97 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 38 00 00 f0 00 5f df e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 08 00 00 6d 00 08 c7 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 1a 00 9d 91 e0 00 00:02:35.315 READ DMA EXT
Error 8 [7] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 68 00 06 1a 00 9e af e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 00 00 5e 3f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 20 00 1c 06 00 9b 7b e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:41.785 READ DMA EXT
Error 7 [6] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 f1 00 5f 2f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:35.315 READ DMA EXT
35 00 00 00 08 00 1c 37 00 90 5f e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:35.315 READ DMA EXT
Error 6 [5] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:37.809 READ DMA EXT
25 00 00 00 08 00 02 f9 00 0d d7 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 08 00 00 15 00 60 77 e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 18 00 00 f1 00 5f 17 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 79 00 94 f7 e0 00 00:02:35.315 READ DMA EXT
Error 5 [4] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 80 00 06 1a 00 9e 97 e0 00 00:02:35.217 READ DMA EXT
25 00 00 00 40 00 02 f9 00 0d 97 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 38 00 00 f0 00 5f df e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 08 00 00 6d 00 08 c7 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 1a 00 9d 91 e0 00 00:02:35.315 READ DMA EXT
Error 4 [3] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 68 00 06 1a 00 9e af e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 00 00 5e 3f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 20 00 1c 06 00 9b 7b e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:41.785 READ DMA EXT
Error 3 [2] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 f1 00 5f 2f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:35.315 READ DMA EXT
35 00 00 00 08 00 1c 37 00 90 5f e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:35.315 READ DMA EXT
Error 2 [1] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:37.809 READ DMA EXT
25 00 00 00 08 00 02 f9 00 0d d7 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 08 00 00 15 00 60 77 e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 18 00 00 f1 00 5f 17 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 79 00 94 f7 e0 00 00:02:35.315 READ DMA EXT
Error 1 [0] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 80 00 06 1a 00 9e 97 e0 00 00:02:35.217 READ DMA EXT
25 00 00 00 40 00 02 f9 00 0d 97 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 38 00 00 f0 00 5f df e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 08 00 00 6d 00 08 c7 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 1a 00 9d 91 e0 00 00:02:35.315 READ DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 18605 -
# 2 Short offline Completed without error 00% 18604 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Commands not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
What's written? is the hard drive going to die?
Last edited by quellen (2021-11-21 20:17:58)
sorry for my bad english
Offline
9 Power_On_Hours -O--CK 079 079 000 - 18605
Error 14 [13] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
18605 - 10703 = ?
There was a singular incident that lead to a couple of uncorrectable IO errors on a single block… how many power-on hours ago?
There're no reallocated or pending or offline uncorrectable errors - there's no indication that the drive will fail in the immediate future.
The IO errors could have been for weakend polarization or a drop of current (so the firmware continued to work but the discs didn't) or … anything. But even on 24/7 that was ~11 months ago.
Offline
Thank you.
however the hard disk is very noisy, especially during Windows startup. I think it will die soon.
sorry for my bad english
Offline
You could run a full test or badblocks, but "noisy" itself isn't necessarily indicative of imminent failure. Eg. if the windows partition is highly fragmented the head will travel around a lot.
Another aspect contributing to noise is bad seating, loose screws, stuff like that that causes vibrations (to be carried on)
Offline
Go for smartctl extend (long) hdd test by 'smartctl -t long /dev/sdX'.
Offline
Go for smartctl extend (long) hdd test by 'smartctl -t long /dev/sdX'.
done. it says: "Completed without error".
gsmartcontrol log:
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.73-1-lts] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10
Device Model: ST3250620AS
Serial Number: CENSURED
Firmware Version: 3.AAD
User Capacity: 250,059,350,016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Thu Nov 25 10:58:59 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, frozen [SEC2]
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 117 088 006 - 165929700
3 Spin_Up_Time PO---- 095 095 000 - 0
4 Start_Stop_Count -O--CK 097 097 020 - 3842
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
7 Seek_Error_Rate POSR-- 065 060 030 - 773578043144
9 Power_On_Hours -O--CK 079 079 000 - 18622
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 096 096 020 - 4166
187 Reported_Uncorrect -O--CK 086 086 000 - 14
189 High_Fly_Writes -O-RCK 100 100 000 - 0
190 Airflow_Temperature_Cel -O---K 061 044 045 Past 39 (Min/Max 23/39)
194 Temperature_Celsius -O---K 039 056 000 - 39 (0 12 0 0 0)
195 Hardware_ECC_Recovered -O-RC- 059 051 000 - 172786765
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0
200 Multi_Zone_Error_Rate ------ 100 253 000 - 0
202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 GPL,SL R/O 1 Summary SMART error log
0x02 GPL,SL R/O 5 Comprehensive SMART error log
0x03 GPL,SL R/O 5 Ext. Comprehensive SMART error log
0x06 GPL,SL R/O 1 SMART self-test log
0x07 GPL,SL R/O 1 Extended self-test log
0x09 GPL,SL R/W 1 Selective self-test log
0x10 GPL,SL R/O 1 NCQ Command Error log
0x11 GPL,SL R/O 1 SATA Phy Event Counters log
0x20 GPL,SL R/O 1 Streaming performance log [OBS-8]
0x21 GPL,SL R/O 1 Write stream error log
0x22 GPL,SL R/O 1 Read stream error log
0x23 GPL,SL R/O 1 Delayed sector log [OBS-8]
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0 GPL,SL VS 1 Device vendor specific log
0xa1 GPL,SL VS 20 Device vendor specific log
0xa2 GPL,SL VS 101 Device vendor specific log
0xa8 GPL,SL VS 20 Device vendor specific log
0xa9 GPL,SL VS 1 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
0xff GPL - 23040 Reserved
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 14
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 14 [13] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:37.809 READ DMA EXT
25 00 00 00 08 00 02 f9 00 0d d7 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 08 00 00 15 00 60 77 e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 18 00 00 f1 00 5f 17 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 79 00 94 f7 e0 00 00:02:35.315 READ DMA EXT
Error 13 [12] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 80 00 06 1a 00 9e 97 e0 00 00:02:35.217 READ DMA EXT
25 00 00 00 40 00 02 f9 00 0d 97 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 38 00 00 f0 00 5f df e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 08 00 00 6d 00 08 c7 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 1a 00 9d 91 e0 00 00:02:35.315 READ DMA EXT
Error 12 [11] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 68 00 06 1a 00 9e af e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 00 00 5e 3f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 20 00 1c 06 00 9b 7b e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:41.785 READ DMA EXT
Error 11 [10] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 f1 00 5f 2f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:35.315 READ DMA EXT
35 00 00 00 08 00 1c 37 00 90 5f e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:35.315 READ DMA EXT
Error 10 [9] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:37.809 READ DMA EXT
25 00 00 00 08 00 02 f9 00 0d d7 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 08 00 00 15 00 60 77 e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 18 00 00 f1 00 5f 17 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 79 00 94 f7 e0 00 00:02:35.315 READ DMA EXT
Error 9 [8] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 80 00 06 1a 00 9e 97 e0 00 00:02:35.217 READ DMA EXT
25 00 00 00 40 00 02 f9 00 0d 97 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 38 00 00 f0 00 5f df e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 08 00 00 6d 00 08 c7 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 1a 00 9d 91 e0 00 00:02:35.315 READ DMA EXT
Error 8 [7] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 68 00 06 1a 00 9e af e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 00 00 5e 3f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 20 00 1c 06 00 9b 7b e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:41.785 READ DMA EXT
Error 7 [6] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 f1 00 5f 2f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:35.315 READ DMA EXT
35 00 00 00 08 00 1c 37 00 90 5f e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:35.315 READ DMA EXT
Error 6 [5] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:37.809 READ DMA EXT
25 00 00 00 08 00 02 f9 00 0d d7 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 08 00 00 15 00 60 77 e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 18 00 00 f1 00 5f 17 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 79 00 94 f7 e0 00 00:02:35.315 READ DMA EXT
Error 5 [4] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 80 00 06 1a 00 9e 97 e0 00 00:02:35.217 READ DMA EXT
25 00 00 00 40 00 02 f9 00 0d 97 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 38 00 00 f0 00 5f df e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 08 00 00 6d 00 08 c7 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 1a 00 9d 91 e0 00 00:02:35.315 READ DMA EXT
Error 4 [3] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 68 00 06 1a 00 9e af e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 00 00 5e 3f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 20 00 1c 06 00 9b 7b e0 00 00:02:41.805 READ DMA EXT
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:41.785 READ DMA EXT
Error 3 [2] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 70 00 06 1a 00 9e a7 e0 00 00:02:37.809 READ DMA EXT
35 00 00 00 08 00 00 f1 00 5f 2f e0 00 00:02:35.332 WRITE DMA EXT
25 00 00 00 01 00 00 00 00 00 00 e0 00 00:02:35.315 READ DMA EXT
35 00 00 00 08 00 1c 37 00 90 5f e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:35.315 READ DMA EXT
Error 2 [1] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 78 00 06 1a 00 9e 9f e0 00 00:02:37.809 READ DMA EXT
25 00 00 00 08 00 02 f9 00 0d d7 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 08 00 00 15 00 60 77 e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 18 00 00 f1 00 5f 17 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 79 00 94 f7 e0 00 00:02:35.315 READ DMA EXT
Error 1 [0] occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 00 00 06 1a f6 9e f6 e0 00 Error: UNC at LBA = 0x61af69ef6 = 26222173942
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 80 00 06 1a 00 9e 97 e0 00 00:02:35.217 READ DMA EXT
25 00 00 00 40 00 02 f9 00 0d 97 e0 00 00:02:35.332 READ DMA EXT
35 00 00 00 38 00 00 f0 00 5f df e0 00 00:02:35.315 WRITE DMA EXT
35 00 00 00 08 00 00 6d 00 08 c7 e0 00 00:02:35.315 WRITE DMA EXT
25 00 00 00 08 00 1c 1a 00 9d 91 e0 00 00:02:35.315 READ DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 18622 -
# 2 Short offline Completed without error 00% 18605 -
# 3 Short offline Completed without error 00% 18604 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Commands not supported
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x000a 2 2 Device-to-host register FISes sent due to a COMRESET
0x0001 2 0 Command failed due to ICRC error
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
$ sudo smartctl -a /dev/sdb
smartctl 7.2 2020-12-30 r5155 [x86_64-linux-5.10.73-1-lts] (local build)
Copyright (C) 2002-20, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.10
Device Model: ST3250620AS
Serial Number: CENSURED
Firmware Version: 3.AAD
User Capacity: 250.059.350.016 bytes [250 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA/ATAPI-7 (minor revision not indicated)
Local Time is: Thu Nov 25 11:12:19 2021 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 088 006 Pre-fail Always - 165929700
3 Spin_Up_Time 0x0003 095 095 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 097 097 020 Old_age Always - 3842
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 065 060 030 Pre-fail Always - 773578043236
9 Power_On_Hours 0x0032 079 079 000 Old_age Always - 18622
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 096 096 020 Old_age Always - 4166
187 Reported_Uncorrect 0x0032 086 086 000 Old_age Always - 14
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 064 044 045 Old_age Always In_the_past 36 (Min/Max 23/39)
194 Temperature_Celsius 0x0022 036 056 000 Old_age Always - 36 (0 12 0 0 0)
195 Hardware_ECC_Recovered 0x001a 059 051 000 Old_age Always - 172792457
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 Data_Address_Mark_Errs 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 14 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 14 occurred at disk power-on lifetime: 18552 hours (773 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 58 0d fe e0 Error: UNC at LBA = 0x00fe0d58 = 16649560
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 01 58 0d fe e0 00 01:10:41.410 READ DMA EXT
25 00 01 57 0d fe e0 00 01:10:41.410 READ DMA EXT
25 00 01 56 0d fe e0 00 01:10:41.410 READ DMA EXT
25 00 01 55 0d fe e0 00 01:10:41.410 READ DMA EXT
25 00 01 54 0d fe e0 00 01:10:41.410 READ DMA EXT
Error 13 occurred at disk power-on lifetime: 18552 hours (773 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 58 0d fe e0 Error: UNC at LBA = 0x00fe0d58 = 16649560
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 c0 20 0d fe e0 00 01:10:38.822 READ DMA EXT
25 00 b6 80 84 d5 e0 00 01:10:38.821 READ DMA EXT
25 00 00 80 83 d5 e0 00 01:10:38.815 READ DMA EXT
35 00 16 30 08 d8 e0 00 01:10:38.812 WRITE DMA EXT
35 00 00 30 07 d8 e0 00 01:10:38.811 WRITE DMA EXT
Error 12 occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f6 1a 9e e0 Error: UNC at LBA = 0x009e1af6 = 10361590
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 28 ef 1a 9e e0 00 00:02:51.767 READ DMA EXT
35 00 08 47 00 5e e0 00 00:02:51.767 WRITE DMA EXT
25 00 30 e7 1a 9e e0 00 00:02:51.767 READ DMA EXT
35 00 10 97 a0 61 e0 00 00:02:51.743 WRITE DMA EXT
35 00 20 57 f1 5f e0 00 00:02:57.700 WRITE DMA EXT
Error 11 occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f6 1a 9e e0 Error: UNC at LBA = 0x009e1af6 = 10361590
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 30 e7 1a 9e e0 00 00:02:51.767 READ DMA EXT
35 00 10 97 a0 61 e0 00 00:02:51.767 WRITE DMA EXT
35 00 20 57 f1 5f e0 00 00:02:51.767 WRITE DMA EXT
25 00 01 00 00 00 e0 00 00:02:51.743 READ DMA EXT
25 00 40 c1 e2 91 e0 00 00:02:51.726 READ DMA EXT
Error 10 occurred at disk power-on lifetime: 10703 hours (445 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 f6 1a 9e e0 Error: UNC at LBA = 0x009e1af6 = 10361590
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 38 df 1a 9e e0 00 00:02:51.767 READ DMA EXT
35 00 08 47 9b 61 e0 00 00:02:51.767 WRITE DMA EXT
25 00 10 01 d2 8e e0 00 00:02:51.767 READ DMA EXT
35 00 08 3f 3e 8e e0 00 00:02:51.743 WRITE DMA EXT
25 00 40 d7 1a 9e e0 00 00:02:51.726 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 18622 -
# 2 Short offline Completed without error 00% 18605 -
# 3 Short offline Completed without error 00% 18604 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
I also defragmented from Windows 10 and after only 5 minutes it says "OK, 0% defragmented"
Last edited by quellen (2021-11-25 10:40:09)
sorry for my bad english
Offline
Test passed fine and there're still not more errors - your disk looks healthy…
(The barracudas rest their heads with a somewhat fearsome tchiiinnnng sound when idling - that's normal)
Offline
Pages: 1