You are not logged in.

Pages: 1 2

Topic closed

#1 2009-02-26 20:16:40

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

[SOLVED]No wired network ?!?!?

Hi guys, I used to have a wireless network up and running, but there was some changes and some moving, and now I'm able to connect to my local network using a cable, which I obviously prefer.

The problem is that, I'm not connecting to the network, I mean, I can't ping the router, and obviously no internet....

Here are my configs, I can't find anything wrong with them...

/etc/rc.conf

...
HOSTNAME="Feio"
eth1="eth1 192.168.1.155 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(eth1)
gateway="default gw 192.168.1.1"
ROUTES=(gateway)
...

/etc/resolv.conf

nameserver 112.113.164.59
nameserver 112.113.164.58
nameserver 112.113.164.51
nameserver 112.113.164.50
search netrabo.com

/etc/hosts

127.0.0.1    Feio.domain.org    localhost.localdomain    localhost Feio

Hope you can help...

P.S. I did use hwdetect to see which kernel module to load (forcedeth), which I did, I also added it to the rc.conf's module list

Last edited by saz (2009-03-17 21:10:25)

Offline

#2 2009-02-26 20:49:37

tomk
Forum Fellow
From: Ireland
Registered: 2004-07-21
Posts: 9,839

Re: [SOLVED]No wired network ?!?!?

Are you sure it's eth1? Is that what ifconfig -a shows you? What's in dmesg when the module is loaded?

Offline

#3 2009-02-26 21:38:49

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

yah I'm very sure. I have eth0 and eth1. I disabled eth0 to ensure there was no confusion.

Offline

#4 2009-02-26 22:44:40

fukawi2
Ex-Administratorino
From: .vic.au
Registered: 2007-09-28
Posts: 6,224
Website

Re: [SOLVED]No wired network ?!?!?

What's the output from `ifconfig` and `ifconfig -a`

Also, if you can install the ethtool package, the output from `ethtool eth0` and `ethtool eth1`

Are you familiar with our Forum Rules, and How To Ask Questions The Smart Way?

BlueHackers // fscanary // resticctl

Offline

#5 2009-02-27 13:27:54

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

[sa@Feio ~]$ ifconfig 
eth1      Link encap:Ethernet  HWaddr 00:1A:92:83:25:21  
          inet addr:192.168.1.155  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:246 Base address:0x8000 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:76 errors:0 dropped:0 overruns:0 frame:0
          TX packets:76 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:5562 (5.4 Kb)  TX bytes:5562 (5.4 Kb)

[sa@Feio ~]$ ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:1A:92:83:1D:8D  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:22 Base address:0x4000 

eth1      Link encap:Ethernet  HWaddr 00:1A:92:83:25:21  
          inet addr:192.168.1.155  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:246 Base address:0x8000 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:76 errors:0 dropped:0 overruns:0 frame:0
          TX packets:76 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:5562 (5.4 Kb)  TX bytes:5562 (5.4 Kb)

Everything as I said before...

Last edited by saz (2009-02-27 13:28:50)

Offline

#6 2009-02-27 14:30:37

tomk
Forum Fellow
From: Ireland
Registered: 2004-07-21
Posts: 9,839

Re: [SOLVED]No wired network ?!?!?

I asked about dmesg earlier. Also, the output of route could be useful.

Offline

#7 2009-02-27 15:48:13

Axell
Member
Registered: 2009-01-11
Posts: 43

Re: [SOLVED]No wired network ?!?!?

Emmm.... Is it ok:

nameserver 312.113.164.59

???:/

Last edited by Axell (2009-02-27 15:48:52)

Offline

#8 2009-02-27 22:55:19

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

Axell wrote:

Emmm.... Is it ok:

nameserver 312.113.164.59

???:/

^^

i changed it... dunno if it's dangerous to put it out there! i'll give it another value so people don't comment that again =P

Last edited by saz (2009-02-27 22:56:04)

Offline

#9 2009-02-28 00:20:24

fukawi2
Ex-Administratorino
From: .vic.au
Registered: 2007-09-28
Posts: 6,224
Website

Re: [SOLVED]No wired network ?!?!?

fukawi2 wrote:

Also, if you can install the ethtool package, the output from `ethtool eth0` and `ethtool eth1`

???

Are you familiar with our Forum Rules, and How To Ask Questions The Smart Way?

BlueHackers // fscanary // resticctl

Offline

#10 2009-03-01 15:22:15

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

fukawi2 wrote:
fukawi2 wrote:

Also, if you can install the ethtool package, the output from `ethtool eth0` and `ethtool eth1`

???

not installed

dmesg

pci 0000:04:0b.0: PME# disabled
pci 0000:00:0f.0: transparent bridge
pci 0000:00:0f.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:0f.0: bridge 32bit mmio: [0xefb00000-0xefbfffff]
pci 0000:00:0f.0: bridge 32bit mmio pref: [0xefa00000-0xefafffff]
pci 0000:00:13.0: bridge io port: [0x9000-0x9fff]
pci 0000:00:13.0: bridge 32bit mmio: [0xef800000-0xef8fffff]
pci 0000:00:13.0: bridge 64bit mmio pref: [0xef700000-0xef7fffff]
pci 0000:00:14.0: bridge io port: [0x8000-0x8fff]
pci 0000:00:14.0: bridge 32bit mmio: [0xef600000-0xef6fffff]
pci 0000:00:14.0: bridge 64bit mmio pref: [0xef500000-0xef5fffff]
pci 0000:00:15.0: bridge io port: [0x7000-0x7fff]
pci 0000:00:15.0: bridge 32bit mmio: [0xef400000-0xef4fffff]
pci 0000:00:15.0: bridge 64bit mmio pref: [0xef300000-0xef3fffff]
pci 0000:00:16.0: bridge io port: [0x6000-0x6fff]
pci 0000:00:16.0: bridge 32bit mmio: [0xef200000-0xef2fffff]
pci 0000:00:16.0: bridge 64bit mmio pref: [0xef100000-0xef1fffff]
pci 0000:00:17.0: bridge io port: [0x5000-0x5fff]
pci 0000:00:17.0: bridge 32bit mmio: [0xef000000-0xef0fffff]
pci 0000:00:17.0: bridge 64bit mmio pref: [0xeef00000-0xeeffffff]
pci 0000:00:18.0: bridge io port: [0x4000-0x4fff]
pci 0000:00:18.0: bridge 32bit mmio: [0xeee00000-0xeeefffff]
pci 0000:00:18.0: bridge 64bit mmio pref: [0xeed00000-0xeedfffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LSA2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: ioport range 0x1000-0x107f has been reserved
system 00:01: ioport range 0x1080-0x10ff has been reserved
system 00:01: ioport range 0x1400-0x147f has been reserved
system 00:01: ioport range 0x1480-0x14ff has been reserved
system 00:01: ioport range 0x1800-0x187f has been reserved
system 00:01: ioport range 0x1880-0x18ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x87f has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:02: ioport range 0x880-0x88f has been reserved
system 00:08: iomem range 0xf0000000-0xf1ffffff has been reserved
system 00:09: iomem range 0xf0000-0xf3fff could not be reserved
system 00:09: iomem range 0xf4000-0xf7fff could not be reserved
system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
system 00:09: iomem range 0xfc000-0xfffff could not be reserved
system 00:09: iomem range 0xfeff0000-0xfeff00ff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0x100000-0x7feeffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfeff0000-0xfeff03ff could not be reserved
pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
pci 0000:00:03.0:   IO window: 0xd000-0xdfff
pci 0000:00:03.0:   MEM window: 0xea000000-0xedffffff
pci 0000:00:03.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:06.0: PCI bridge, secondary bus 0000:02
pci 0000:00:06.0:   IO window: 0xb000-0xbfff
pci 0000:00:06.0:   MEM window: 0xefc00000-0xefcfffff
pci 0000:00:06.0:   PREFETCH window: 0x000000ef900000-0x000000ef9fffff
pci 0000:00:07.0: PCI bridge, secondary bus 0000:03
pci 0000:00:07.0:   IO window: 0xa000-0xafff
pci 0000:00:07.0:   MEM window: 0xefe00000-0xefefffff
pci 0000:00:07.0:   PREFETCH window: 0x000000efd00000-0x000000efdfffff
pci 0000:00:0f.0: PCI bridge, secondary bus 0000:04
pci 0000:00:0f.0:   IO window: 0xc000-0xcfff
pci 0000:00:0f.0:   MEM window: 0xefb00000-0xefbfffff
pci 0000:00:0f.0:   PREFETCH window: 0x000000efa00000-0x000000efafffff
pci 0000:00:13.0: PCI bridge, secondary bus 0000:05
pci 0000:00:13.0:   IO window: 0x9000-0x9fff
pci 0000:00:13.0:   MEM window: 0xef800000-0xef8fffff
pci 0000:00:13.0:   PREFETCH window: 0x000000ef700000-0x000000ef7fffff
pci 0000:00:14.0: PCI bridge, secondary bus 0000:06
pci 0000:00:14.0:   IO window: 0x8000-0x8fff
pci 0000:00:14.0:   MEM window: 0xef600000-0xef6fffff
pci 0000:00:14.0:   PREFETCH window: 0x000000ef500000-0x000000ef5fffff
pci 0000:00:15.0: PCI bridge, secondary bus 0000:07
pci 0000:00:15.0:   IO window: 0x7000-0x7fff
pci 0000:00:15.0:   MEM window: 0xef400000-0xef4fffff
pci 0000:00:15.0:   PREFETCH window: 0x000000ef300000-0x000000ef3fffff
pci 0000:00:16.0: PCI bridge, secondary bus 0000:08
pci 0000:00:16.0:   IO window: 0x6000-0x6fff
pci 0000:00:16.0:   MEM window: 0xef200000-0xef2fffff
pci 0000:00:16.0:   PREFETCH window: 0x000000ef100000-0x000000ef1fffff
pci 0000:00:17.0: PCI bridge, secondary bus 0000:09
pci 0000:00:17.0:   IO window: 0x5000-0x5fff
pci 0000:00:17.0:   MEM window: 0xef000000-0xef0fffff
pci 0000:00:17.0:   PREFETCH window: 0x000000eef00000-0x000000eeffffff
pci 0000:00:18.0: PCI bridge, secondary bus 0000:0a
pci 0000:00:18.0:   IO window: 0x4000-0x4fff
pci 0000:00:18.0:   MEM window: 0xeee00000-0xeeefffff
pci 0000:00:18.0:   PREFETCH window: 0x000000eed00000-0x000000eedfffff
pci 0000:00:03.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:0f.0: setting latency timer to 64
pci 0000:00:13.0: setting latency timer to 64
pci 0000:00:14.0: setting latency timer to 64
pci 0000:00:15.0: setting latency timer to 64
pci 0000:00:16.0: setting latency timer to 64
pci 0000:00:17.0: setting latency timer to 64
pci 0000:00:18.0: setting latency timer to 64
bus: 00 index 0 io port: [0x00-0xffff]
bus: 00 index 1 mmio: [0x000000-0xffffffff]
bus: 01 index 0 io port: [0xd000-0xdfff]
bus: 01 index 1 mmio: [0xea000000-0xedffffff]
bus: 01 index 2 mmio: [0xd0000000-0xdfffffff]
bus: 01 index 3 mmio: [0x0-0x0]
bus: 02 index 0 io port: [0xb000-0xbfff]
bus: 02 index 1 mmio: [0xefc00000-0xefcfffff]
bus: 02 index 2 mmio: [0xef900000-0xef9fffff]
bus: 02 index 3 mmio: [0x0-0x0]
bus: 03 index 0 io port: [0xa000-0xafff]
bus: 03 index 1 mmio: [0xefe00000-0xefefffff]
bus: 03 index 2 mmio: [0xefd00000-0xefdfffff]
bus: 03 index 3 mmio: [0x0-0x0]
bus: 04 index 0 io port: [0xc000-0xcfff]
bus: 04 index 1 mmio: [0xefb00000-0xefbfffff]
bus: 04 index 2 mmio: [0xefa00000-0xefafffff]
bus: 04 index 3 io port: [0x00-0xffff]
bus: 04 index 4 mmio: [0x000000-0xffffffff]
bus: 05 index 0 io port: [0x9000-0x9fff]
bus: 05 index 1 mmio: [0xef800000-0xef8fffff]
bus: 05 index 2 mmio: [0xef700000-0xef7fffff]
bus: 05 index 3 mmio: [0x0-0x0]
bus: 06 index 0 io port: [0x8000-0x8fff]
bus: 06 index 1 mmio: [0xef600000-0xef6fffff]
bus: 06 index 2 mmio: [0xef500000-0xef5fffff]
bus: 06 index 3 mmio: [0x0-0x0]
bus: 07 index 0 io port: [0x7000-0x7fff]
bus: 07 index 1 mmio: [0xef400000-0xef4fffff]
bus: 07 index 2 mmio: [0xef300000-0xef3fffff]
bus: 07 index 3 mmio: [0x0-0x0]
bus: 08 index 0 io port: [0x6000-0x6fff]
bus: 08 index 1 mmio: [0xef200000-0xef2fffff]
bus: 08 index 2 mmio: [0xef100000-0xef1fffff]
bus: 08 index 3 mmio: [0x0-0x0]
bus: 09 index 0 io port: [0x5000-0x5fff]
bus: 09 index 1 mmio: [0xef000000-0xef0fffff]
bus: 09 index 2 mmio: [0xeef00000-0xeeffffff]
bus: 09 index 3 mmio: [0x0-0x0]
bus: 0a index 0 io port: [0x4000-0x4fff]
bus: 0a index 1 mmio: [0xeee00000-0xeeefffff]
bus: 0a index 2 mmio: [0xeed00000-0xeedfffff]
bus: 0a index 3 mmio: [0x0-0x0]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs...<7>Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
 done
Freeing initrd memory: 4006k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1732
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:03.0: Disabling HT MSI mapping<6>pci 0000:00:06.0: Disabling HT MSI mapping<6>pci 0000:00:07.0: Disabling HT MSI mapping<6>pci 0000:00:0e.0: Disabling HT MSI mapping<6>pci 0000:00:0e.1: Disabling HT MSI mapping<6>pci 0000:00:0e.2: Disabling HT MSI mapping<6>pci 0000:00:0f.0: Disabling HT MSI mapping<6>pci 0000:00:11.0: Disabling HT MSI mapping<6>pci 0000:00:12.0: Disabling HT MSI mapping<6>pci 0000:00:13.0: Disabling HT MSI mapping<6>pci 0000:00:14.0: Disabling HT MSI mapping<6>pci 0000:00:15.0: Disabling HT MSI mapping<6>pci 0000:00:16.0: Disabling HT MSI mapping<6>pci 0000:00:17.0: Disabling HT MSI mapping<6>pci 0000:00:18.0: Disabling HT MSI mapping<7>pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:03.0: setting latency timer to 64
pcieport-driver 0000:00:03.0: found MSI capability
pcieport-driver 0000:00:03.0: irq 767 for MSI/MSI-X
pci_express 0000:00:03.0:pcie00: allocate port service
pci_express 0000:00:03.0:pcie03: allocate port service
pcieport-driver 0000:00:06.0: setting latency timer to 64
pcieport-driver 0000:00:06.0: found MSI capability
pcieport-driver 0000:00:06.0: irq 766 for MSI/MSI-X
pci_express 0000:00:06.0:pcie00: allocate port service
pci_express 0000:00:06.0:pcie03: allocate port service
pcieport-driver 0000:00:07.0: setting latency timer to 64
pcieport-driver 0000:00:07.0: found MSI capability
pcieport-driver 0000:00:07.0: irq 765 for MSI/MSI-X
pci_express 0000:00:07.0:pcie00: allocate port service
pci_express 0000:00:07.0:pcie03: allocate port service
pcieport-driver 0000:00:13.0: setting latency timer to 64
pcieport-driver 0000:00:13.0: found MSI capability
pcieport-driver 0000:00:13.0: irq 764 for MSI/MSI-X
pci_express 0000:00:13.0:pcie00: allocate port service
pci_express 0000:00:13.0:pcie03: allocate port service
pcieport-driver 0000:00:14.0: setting latency timer to 64
pcieport-driver 0000:00:14.0: found MSI capability
pcieport-driver 0000:00:14.0: irq 763 for MSI/MSI-X
pci_express 0000:00:14.0:pcie00: allocate port service
pci_express 0000:00:14.0:pcie03: allocate port service
pcieport-driver 0000:00:15.0: setting latency timer to 64
pcieport-driver 0000:00:15.0: found MSI capability
pcieport-driver 0000:00:15.0: irq 762 for MSI/MSI-X
pci_express 0000:00:15.0:pcie00: allocate port service
pci_express 0000:00:15.0:pcie03: allocate port service
pcieport-driver 0000:00:16.0: setting latency timer to 64
pcieport-driver 0000:00:16.0: found MSI capability
pcieport-driver 0000:00:16.0: irq 761 for MSI/MSI-X
pci_express 0000:00:16.0:pcie00: allocate port service
pci_express 0000:00:16.0:pcie03: allocate port service
pcieport-driver 0000:00:17.0: setting latency timer to 64
pcieport-driver 0000:00:17.0: found MSI capability
pcieport-driver 0000:00:17.0: irq 760 for MSI/MSI-X
pci_express 0000:00:17.0:pcie00: allocate port service
pci_express 0000:00:17.0:pcie03: allocate port service
pcieport-driver 0000:00:18.0: setting latency timer to 64
pcieport-driver 0000:00:18.0: found MSI capability
pcieport-driver 0000:00:18.0: irq 759 for MSI/MSI-X
pci_express 0000:00:18.0:pcie00: allocate port service
pci_express 0000:00:18.0:pcie03: allocate port service
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /class/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 332k freed
SCSI subsystem initialized
libata version 3.00 loaded.
pata_acpi 0000:00:0d.0: setting latency timer to 64
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
pata_acpi 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
pata_acpi 0000:00:0e.0: setting latency timer to 64
pata_acpi 0000:00:0e.0: PCI INT A disabled
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
pata_acpi 0000:00:0e.1: PCI INT B -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
pata_acpi 0000:00:0e.1: setting latency timer to 64
pata_acpi 0000:00:0e.1: PCI INT B disabled
ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21
pata_acpi 0000:00:0e.2: PCI INT C -> Link[ASA2] -> GSI 21 (level, low) -> IRQ 21
pata_acpi 0000:00:0e.2: setting latency timer to 64
pata_acpi 0000:00:0e.2: PCI INT C disabled
pata_amd 0000:00:0d.0: version 0.3.10
pata_amd 0000:00:0d.0: setting latency timer to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
ata1.00: ATAPI: HL-DT-ST RW/DVD GCC-4480B, 1.00, max UDMA/33
ata1.01: ATA-6: ST380011A, 3.06, max UDMA/100
ata1.01: 156301488 sectors, multi 1: LBA48 
ata1: nv_mode_filter: 0x739f&0x701f->0x701f, BIOS=0x7000 (0xc0c60000) ACPI=0x701f (60:20:0x1f)
ata1: nv_mode_filter: 0x3f39f&0x3f01f->0x3f01f, BIOS=0x3f000 (0xc0c60000) ACPI=0x3f01f (60:20:0x1f)
ata1.00: configured for UDMA/33
ata1.01: configured for UDMA/100
ata2: port disabled. ignoring.
scsi 0:0:0:0: CD-ROM            HL-DT-ST RW/DVD GCC-4480B 1.00 PQ: 0 ANSI: 5
scsi 0:0:1:0: Direct-Access     ATA      ST380011A        3.06 PQ: 0 ANSI: 5
sata_nv 0000:00:0e.0: version 3.5
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xf700 irq 23
ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xf708 irq 23
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: native sectors (586072368) is smaller than sectors (625142448)
ata3.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
ata3.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
ata4: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access     ATA      ST3320620AS      3.AA PQ: 0 ANSI: 5
sata_nv 0000:00:0e.1: PCI INT B -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:0e.1: Using SWNCQ mode
sata_nv 0000:00:0e.1: setting latency timer to 64
scsi4 : sata_nv
scsi5 : sata_nv
ata5: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xf200 irq 22
ata6: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xf208 irq 22
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
sata_nv 0000:00:0e.2: PCI INT C -> Link[ASA2] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.2: Using SWNCQ mode
sata_nv 0000:00:0e.2: setting latency timer to 64
scsi6 : sata_nv
scsi7 : sata_nv
ata7: SATA max UDMA/133 cmd 0xf100 ctl 0xf000 bmdma 0xed00 irq 21
ata8: SATA max UDMA/133 cmd 0xef00 ctl 0xee00 bmdma 0xed08 irq 21
ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata7.00: ATAPI: TSSTcorp CDDVDW SH-S203B, SB00, max UDMA/100
ata7.00: configured for UDMA/100
ata8: SATA link down (SStatus 0 SControl 300)
scsi 6:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S203B  SB00 PQ: 0 ANSI: 5
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:1:0: [sda] 156301488 512-byte hardware sectors: (80.0 GB/74.5 GiB)
sd 0:0:1:0: [sda] Write Protect is off
sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sda] 156301488 512-byte hardware sectors: (80.0 GB/74.5 GiB)
sd 0:0:1:0: [sda] Write Protect is off
sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:<6>usbcore: registered new device driver usb
 sda1
sd 0:0:1:0: [sda] Attached SCSI disk
sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb:ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:0b.1: setting latency timer to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.1: debug port 1
ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
ehci_hcd 0000:00:0b.1: irq 20, io mem 0xefffe000
Driver 'sr' needs updating - please use bus_type methods
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
 sdb1 sdb2 sdb3
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23
ohci_hcd 0000:00:0b.0: setting latency timer to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: irq 23, io mem 0xeffff000
sd 2:0:0:0: [sdb] Attached SCSI disk
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
sr 6:0:0:0: Attached scsi CD-ROM sr1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi8 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb 2-4: new full speed USB device using ohci_hcd and address 2
usb 2-4: configuration #1 chosen from 1 choice
hub 2-4:1.0: USB hub found
hub 2-4:1.0: 4 ports detected
usb 2-4.1: new low speed USB device using ohci_hcd and address 3
usb 2-4.1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: G15 Gaming Keyboard as /class/input/input1
generic-usb 0003:046D:C226.0001: input,hidraw0: USB HID v1.10 Keyboard [G15 Gaming Keyboard] on usb-0000:00:0b.0-4.1/input0
input: G15 Gaming Keyboard as /class/input/input2
generic-usb 0003:046D:C226.0002: input,hiddev0,hidraw1: USB HID v1.10 Device [G15 Gaming Keyboard] on usb-0000:00:0b.0-4.1/input1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usb 2-4.3: new full speed USB device using ohci_hcd and address 4
usb 2-4.3: configuration #1 chosen from 1 choice
input: Logitech USB Gaming Mouse as /class/input/input3
generic-usb 0003:046D:C041.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:0b.0-4.3/input0
generic-usb 0003:046D:C041.0004: hiddev1,hidraw3: USB HID v1.11 Device [Logitech USB Gaming Mouse] on usb-0000:00:0b.0-4.3/input1
usb 2-4.4: new full speed USB device using ohci_hcd and address 5
usb 2-4.4: configuration #1 chosen from 1 choice
input: G15 GamePanel LCD as /class/input/input4
generic-usb 0003:046D:C227.0005: input,hiddev2,hidraw4: USB HID v1.11 Keypad [G15 GamePanel LCD] on usb-0000:00:0b.0-4.4/input0
scsi 8:0:0:0: Direct-Access     ST350083 0AS                   PQ: 0 ANSI: 2
sd 8:0:0:0: [sdc] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 8:0:0:0: [sdc] Write Protect is off
sd 8:0:0:0: [sdc] Mode Sense: 38 00 00 00
sd 8:0:0:0: [sdc] Assuming drive cache: write through
sd 8:0:0:0: [sdc] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 8:0:0:0: [sdc] Write Protect is off
sd 8:0:0:0: [sdc] Mode Sense: 38 00 00 00
sd 8:0:0:0: [sdc] Assuming drive cache: write through
 sdc: sdc1
sd 8:0:0:0: [sdc] Attached SCSI disk
usb-storage: device scan complete
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
rtc_cmos 00:05: RTC can wake from S4
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
forcedeth 0000:00:11.0: PCI INT A -> Link[APCH] -> GSI 22 (level, low) -> IRQ 22
forcedeth 0000:00:11.0: setting latency timer to 64
nv_probe: set workaround bit for reversed mac addr
forcedeth 0000:00:11.0: ifname eth0, PHY OUI 0x5043 @ 19, addr 00:1a:92:83:1d:8d
forcedeth 0000:00:11.0: highdma csum vlan pwrctl mgmt timirq gbit lnktim msi desc-v3
ACPI: PCI Interrupt Link [AMC1] enabled at IRQ 21
forcedeth 0000:00:12.0: PCI INT A -> Link[AMC1] -> GSI 21 (level, low) -> IRQ 21
forcedeth 0000:00:12.0: setting latency timer to 64
nv_probe: set workaround bit for reversed mac addr
forcedeth 0000:00:12.0: ifname eth1, PHY OUI 0x5043 @ 19, addr 00:1a:92:83:25:21
forcedeth 0000:00:12.0: highdma csum vlan pwrctl mgmt timirq gbit lnktim msi desc-v3
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
C-Media PCI 0000:04:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
input: Power Button (FF) as /class/input/input5
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input6
ACPI: Power Button (CM) [PWRB]
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN] (on)
processor ACPI_CPU:00: registered as cooling_device1
processor ACPI_CPU:01: registered as cooling_device2
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00
ACPI: I/O resource nForce2_smbus [0x1c80-0x1cbf] conflicts with ACPI region SM01 [0x1c80-0x1c85]
ACPI: Device needs an ACPI driver
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c80
Linux agpgart interface v0.103
nvidia: module license 'NVIDIA' taints kernel.
input: PC Speaker as /class/input/input7
Error: Driver 'pcspkr' is already registered, aborting...
sr 0:0:0:0: Attached scsi generic sg0 type 5
sd 0:0:1:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
sr 6:0:0:0: Attached scsi generic sg3 type 5
sd 8:0:0:0: Attached scsi generic sg4 type 0
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ohci1394 0000:04:0b.0: PCI INT A -> Link[APC4] -> GSI 19 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19]  MMIO=[efbff000-efbff7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
nvidia 0000:01:00.0: PCI INT A -> Link[APC5] -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module  180.22  Tue Jan  6 09:29:08 PST 2009
EXT3 FS on sdb2, internal journal
fuse init (API version 7.10)
Adding 324272k swap on /dev/sdb3.  Priority:-1 extents:1 across:324272k
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0011d800012b943c]
forcedeth 0000:00:12.0: irq 758 for MSI/MSI-X
eth1: no link during initialization.
it87: Found IT8718F chip at 0x290, revision 2
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
coretemp coretemp.0: Using relative temperature scale!
coretemp coretemp.1: Using relative temperature scale!
input: G15 Extra Keys as /class/input/input8

route

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.1.0   *               255.255.255.0   U     0      0        0 eth1
default         192.168.1.1   0.0.0.0         UG    0      0        0 eth1

Offline

#11 2009-03-01 16:40:54

tomk
Forum Fellow
From: Ireland
Registered: 2004-07-21
Posts: 9,839

Re: [SOLVED]No wired network ?!?!?

"eth1: no link during initialization" is the relevant error here. You should google it for more info.

In the meanwhile, is there some reason why you can't use eth0? Based on the output above, it seems to be OK.

Offline

#12 2009-03-01 17:31:12

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

tomk wrote:

"eth1: no link during initialization" is the relevant error here. You should google it for more info.

In the meanwhile, is there some reason why you can't use eth0? Based on the output above, it seems to be OK.

no reason. actually I was using eth0 before trying eth1. the problem was exactly the same.

Offline

#13 2009-03-05 20:29:28

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

so today I decided to use DHCP instead:

rc.conf

eth0="dhcp"
eth1="dhcp"
INTERFACES=(eth0 eth1)

gateway="default gw 192.168.1.1"
ROUTES=(!gateway)

I tested with both interfaces, and it always times out.

Last edited by saz (2009-03-05 23:48:23)

Offline

#14 2009-03-06 16:01:26

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

bump..


I installed the ethtool pkg, and decided to post here the output, maybe it'll help... I'm also posting dmesg, because as I said on my previous post I also activated eth0, and configured both interfaces to use dhcp, and that changes things a bit..


dmesg

pci 0000:04:07.0: supports D1 D2
pci 0000:04:0b.0: reg 10 32bit mmio: [0xefbff000-0xefbff7ff]
pci 0000:04:0b.0: reg 14 io port: [0xcf00-0xcf7f]
pci 0000:04:0b.0: supports D2
pci 0000:04:0b.0: PME# supported from D2 D3hot D3cold
pci 0000:04:0b.0: PME# disabled
pci 0000:00:0f.0: transparent bridge
pci 0000:00:0f.0: bridge io port: [0xc000-0xcfff]
pci 0000:00:0f.0: bridge 32bit mmio: [0xefb00000-0xefbfffff]
pci 0000:00:0f.0: bridge 32bit mmio pref: [0xefa00000-0xefafffff]
pci 0000:00:13.0: bridge io port: [0x9000-0x9fff]
pci 0000:00:13.0: bridge 32bit mmio: [0xef800000-0xef8fffff]
pci 0000:00:13.0: bridge 64bit mmio pref: [0xef700000-0xef7fffff]
pci 0000:00:14.0: bridge io port: [0x8000-0x8fff]
pci 0000:00:14.0: bridge 32bit mmio: [0xef600000-0xef6fffff]
pci 0000:00:14.0: bridge 64bit mmio pref: [0xef500000-0xef5fffff]
pci 0000:00:15.0: bridge io port: [0x7000-0x7fff]
pci 0000:00:15.0: bridge 32bit mmio: [0xef400000-0xef4fffff]
pci 0000:00:15.0: bridge 64bit mmio pref: [0xef300000-0xef3fffff]
pci 0000:00:16.0: bridge io port: [0x6000-0x6fff]
pci 0000:00:16.0: bridge 32bit mmio: [0xef200000-0xef2fffff]
pci 0000:00:16.0: bridge 64bit mmio pref: [0xef100000-0xef1fffff]
pci 0000:00:17.0: bridge io port: [0x5000-0x5fff]
pci 0000:00:17.0: bridge 32bit mmio: [0xef000000-0xef0fffff]
pci 0000:00:17.0: bridge 64bit mmio pref: [0xeef00000-0xeeffffff]
pci 0000:00:18.0: bridge io port: [0x4000-0x4fff]
pci 0000:00:18.0: bridge 32bit mmio: [0xeee00000-0xeeefffff]
pci 0000:00:18.0: bridge 64bit mmio pref: [0xeed00000-0xeedfffff]
bus 00 -> node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 *7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LP2P] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LMC1] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LAZA] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LSA2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [AMC1] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0
ACPI: PCI Interrupt Link [ASA2] (IRQs 20 21 22 23) *0
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:01: ioport range 0x1000-0x107f has been reserved
system 00:01: ioport range 0x1080-0x10ff has been reserved
system 00:01: ioport range 0x1400-0x147f has been reserved
system 00:01: ioport range 0x1480-0x14ff has been reserved
system 00:01: ioport range 0x1800-0x187f has been reserved
system 00:01: ioport range 0x1880-0x18ff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
system 00:02: ioport range 0x800-0x87f has been reserved
system 00:02: ioport range 0x290-0x297 has been reserved
system 00:02: ioport range 0x880-0x88f has been reserved
system 00:08: iomem range 0xf0000000-0xf1ffffff has been reserved
system 00:09: iomem range 0xf0000-0xf3fff could not be reserved
system 00:09: iomem range 0xf4000-0xf7fff could not be reserved
system 00:09: iomem range 0xf8000-0xfbfff could not be reserved
system 00:09: iomem range 0xfc000-0xfffff could not be reserved
system 00:09: iomem range 0xfeff0000-0xfeff00ff has been reserved
system 00:09: iomem range 0x7fef0000-0x7fefffff could not be reserved
system 00:09: iomem range 0xffff0000-0xffffffff has been reserved
system 00:09: iomem range 0x0-0x9ffff could not be reserved
system 00:09: iomem range 0x100000-0x7feeffff could not be reserved
system 00:09: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:09: iomem range 0xfeff0000-0xfeff03ff could not be reserved
pci 0000:00:03.0: PCI bridge, secondary bus 0000:01
pci 0000:00:03.0:   IO window: 0xd000-0xdfff
pci 0000:00:03.0:   MEM window: 0xea000000-0xedffffff
pci 0000:00:03.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
pci 0000:00:06.0: PCI bridge, secondary bus 0000:02
pci 0000:00:06.0:   IO window: 0xb000-0xbfff
pci 0000:00:06.0:   MEM window: 0xefc00000-0xefcfffff
pci 0000:00:06.0:   PREFETCH window: 0x000000ef900000-0x000000ef9fffff
pci 0000:00:07.0: PCI bridge, secondary bus 0000:03
pci 0000:00:07.0:   IO window: 0xa000-0xafff
pci 0000:00:07.0:   MEM window: 0xefe00000-0xefefffff
pci 0000:00:07.0:   PREFETCH window: 0x000000efd00000-0x000000efdfffff
pci 0000:00:0f.0: PCI bridge, secondary bus 0000:04
pci 0000:00:0f.0:   IO window: 0xc000-0xcfff
pci 0000:00:0f.0:   MEM window: 0xefb00000-0xefbfffff
pci 0000:00:0f.0:   PREFETCH window: 0x000000efa00000-0x000000efafffff
pci 0000:00:13.0: PCI bridge, secondary bus 0000:05
pci 0000:00:13.0:   IO window: 0x9000-0x9fff
pci 0000:00:13.0:   MEM window: 0xef800000-0xef8fffff
pci 0000:00:13.0:   PREFETCH window: 0x000000ef700000-0x000000ef7fffff
pci 0000:00:14.0: PCI bridge, secondary bus 0000:06
pci 0000:00:14.0:   IO window: 0x8000-0x8fff
pci 0000:00:14.0:   MEM window: 0xef600000-0xef6fffff
pci 0000:00:14.0:   PREFETCH window: 0x000000ef500000-0x000000ef5fffff
pci 0000:00:15.0: PCI bridge, secondary bus 0000:07
pci 0000:00:15.0:   IO window: 0x7000-0x7fff
pci 0000:00:15.0:   MEM window: 0xef400000-0xef4fffff
pci 0000:00:15.0:   PREFETCH window: 0x000000ef300000-0x000000ef3fffff
pci 0000:00:16.0: PCI bridge, secondary bus 0000:08
pci 0000:00:16.0:   IO window: 0x6000-0x6fff
pci 0000:00:16.0:   MEM window: 0xef200000-0xef2fffff
pci 0000:00:16.0:   PREFETCH window: 0x000000ef100000-0x000000ef1fffff
pci 0000:00:17.0: PCI bridge, secondary bus 0000:09
pci 0000:00:17.0:   IO window: 0x5000-0x5fff
pci 0000:00:17.0:   MEM window: 0xef000000-0xef0fffff
pci 0000:00:17.0:   PREFETCH window: 0x000000eef00000-0x000000eeffffff
pci 0000:00:18.0: PCI bridge, secondary bus 0000:0a
pci 0000:00:18.0:   IO window: 0x4000-0x4fff
pci 0000:00:18.0:   MEM window: 0xeee00000-0xeeefffff
pci 0000:00:18.0:   PREFETCH window: 0x000000eed00000-0x000000eedfffff
pci 0000:00:03.0: setting latency timer to 64
pci 0000:00:06.0: setting latency timer to 64
pci 0000:00:07.0: setting latency timer to 64
pci 0000:00:0f.0: setting latency timer to 64
pci 0000:00:13.0: setting latency timer to 64
pci 0000:00:14.0: setting latency timer to 64
pci 0000:00:15.0: setting latency timer to 64
pci 0000:00:16.0: setting latency timer to 64
pci 0000:00:17.0: setting latency timer to 64
pci 0000:00:18.0: setting latency timer to 64
bus: 00 index 0 io port: [0x00-0xffff]
bus: 00 index 1 mmio: [0x000000-0xffffffff]
bus: 01 index 0 io port: [0xd000-0xdfff]
bus: 01 index 1 mmio: [0xea000000-0xedffffff]
bus: 01 index 2 mmio: [0xd0000000-0xdfffffff]
bus: 01 index 3 mmio: [0x0-0x0]
bus: 02 index 0 io port: [0xb000-0xbfff]
bus: 02 index 1 mmio: [0xefc00000-0xefcfffff]
bus: 02 index 2 mmio: [0xef900000-0xef9fffff]
bus: 02 index 3 mmio: [0x0-0x0]
bus: 03 index 0 io port: [0xa000-0xafff]
bus: 03 index 1 mmio: [0xefe00000-0xefefffff]
bus: 03 index 2 mmio: [0xefd00000-0xefdfffff]
bus: 03 index 3 mmio: [0x0-0x0]
bus: 04 index 0 io port: [0xc000-0xcfff]
bus: 04 index 1 mmio: [0xefb00000-0xefbfffff]
bus: 04 index 2 mmio: [0xefa00000-0xefafffff]
bus: 04 index 3 io port: [0x00-0xffff]
bus: 04 index 4 mmio: [0x000000-0xffffffff]
bus: 05 index 0 io port: [0x9000-0x9fff]
bus: 05 index 1 mmio: [0xef800000-0xef8fffff]
bus: 05 index 2 mmio: [0xef700000-0xef7fffff]
bus: 05 index 3 mmio: [0x0-0x0]
bus: 06 index 0 io port: [0x8000-0x8fff]
bus: 06 index 1 mmio: [0xef600000-0xef6fffff]
bus: 06 index 2 mmio: [0xef500000-0xef5fffff]
bus: 06 index 3 mmio: [0x0-0x0]
bus: 07 index 0 io port: [0x7000-0x7fff]
bus: 07 index 1 mmio: [0xef400000-0xef4fffff]
bus: 07 index 2 mmio: [0xef300000-0xef3fffff]
bus: 07 index 3 mmio: [0x0-0x0]
bus: 08 index 0 io port: [0x6000-0x6fff]
bus: 08 index 1 mmio: [0xef200000-0xef2fffff]
bus: 08 index 2 mmio: [0xef100000-0xef1fffff]
bus: 08 index 3 mmio: [0x0-0x0]
bus: 09 index 0 io port: [0x5000-0x5fff]
bus: 09 index 1 mmio: [0xef000000-0xef0fffff]
bus: 09 index 2 mmio: [0xeef00000-0xeeffffff]
bus: 09 index 3 mmio: [0x0-0x0]
bus: 0a index 0 io port: [0x4000-0x4fff]
bus: 0a index 1 mmio: [0xeee00000-0xeeefffff]
bus: 0a index 2 mmio: [0xeed00000-0xeedfffff]
bus: 0a index 3 mmio: [0x0-0x0]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Unpacking initramfs...<7>Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
 done
Freeing initrd memory: 4006k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1732
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:03.0: Disabling HT MSI mapping<6>pci 0000:00:06.0: Disabling HT MSI mapping<6>pci 0000:00:07.0: Disabling HT MSI mapping<6>pci 0000:00:0e.0: Disabling HT MSI mapping<6>pci 0000:00:0e.1: Disabling HT MSI mapping<6>pci 0000:00:0e.2: Disabling HT MSI mapping<6>pci 0000:00:0f.0: Disabling HT MSI mapping<6>pci 0000:00:11.0: Disabling HT MSI mapping<6>pci 0000:00:12.0: Disabling HT MSI mapping<6>pci 0000:00:13.0: Disabling HT MSI mapping<6>pci 0000:00:14.0: Disabling HT MSI mapping<6>pci 0000:00:15.0: Disabling HT MSI mapping<6>pci 0000:00:16.0: Disabling HT MSI mapping<6>pci 0000:00:17.0: Disabling HT MSI mapping<6>pci 0000:00:18.0: Disabling HT MSI mapping<7>pci 0000:01:00.0: Boot video device
pcieport-driver 0000:00:03.0: setting latency timer to 64
pcieport-driver 0000:00:03.0: found MSI capability
pcieport-driver 0000:00:03.0: irq 767 for MSI/MSI-X
pci_express 0000:00:03.0:pcie00: allocate port service
pci_express 0000:00:03.0:pcie03: allocate port service
pcieport-driver 0000:00:06.0: setting latency timer to 64
pcieport-driver 0000:00:06.0: found MSI capability
pcieport-driver 0000:00:06.0: irq 766 for MSI/MSI-X
pci_express 0000:00:06.0:pcie00: allocate port service
pci_express 0000:00:06.0:pcie03: allocate port service
pcieport-driver 0000:00:07.0: setting latency timer to 64
pcieport-driver 0000:00:07.0: found MSI capability
pcieport-driver 0000:00:07.0: irq 765 for MSI/MSI-X
pci_express 0000:00:07.0:pcie00: allocate port service
pci_express 0000:00:07.0:pcie03: allocate port service
pcieport-driver 0000:00:13.0: setting latency timer to 64
pcieport-driver 0000:00:13.0: found MSI capability
pcieport-driver 0000:00:13.0: irq 764 for MSI/MSI-X
pci_express 0000:00:13.0:pcie00: allocate port service
pci_express 0000:00:13.0:pcie03: allocate port service
pcieport-driver 0000:00:14.0: setting latency timer to 64
pcieport-driver 0000:00:14.0: found MSI capability
pcieport-driver 0000:00:14.0: irq 763 for MSI/MSI-X
pci_express 0000:00:14.0:pcie00: allocate port service
pci_express 0000:00:14.0:pcie03: allocate port service
pcieport-driver 0000:00:15.0: setting latency timer to 64
pcieport-driver 0000:00:15.0: found MSI capability
pcieport-driver 0000:00:15.0: irq 762 for MSI/MSI-X
pci_express 0000:00:15.0:pcie00: allocate port service
pci_express 0000:00:15.0:pcie03: allocate port service
pcieport-driver 0000:00:16.0: setting latency timer to 64
pcieport-driver 0000:00:16.0: found MSI capability
pcieport-driver 0000:00:16.0: irq 761 for MSI/MSI-X
pci_express 0000:00:16.0:pcie00: allocate port service
pci_express 0000:00:16.0:pcie03: allocate port service
pcieport-driver 0000:00:17.0: setting latency timer to 64
pcieport-driver 0000:00:17.0: found MSI capability
pcieport-driver 0000:00:17.0: irq 760 for MSI/MSI-X
pci_express 0000:00:17.0:pcie00: allocate port service
pci_express 0000:00:17.0:pcie03: allocate port service
pcieport-driver 0000:00:18.0: setting latency timer to 64
pcieport-driver 0000:00:18.0: found MSI capability
pcieport-driver 0000:00:18.0: irq 759 for MSI/MSI-X
pci_express 0000:00:18.0:pcie00: allocate port service
pci_express 0000:00:18.0:pcie03: allocate port service
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver4 ports, IRQ sharing disabled
input: Macintosh mouse button emulation as /class/input/input0
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Freeing unused kernel memory: 332k freed
SCSI subsystem initialized
libata version 3.00 loaded.
pata_acpi 0000:00:0d.0: setting latency timer to 64
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23
pata_acpi 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
pata_acpi 0000:00:0e.0: setting latency timer to 64
pata_acpi 0000:00:0e.0: PCI INT A disabled
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22
pata_acpi 0000:00:0e.1: PCI INT B -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
pata_acpi 0000:00:0e.1: setting latency timer to 64
pata_acpi 0000:00:0e.1: PCI INT B disabled
ACPI: PCI Interrupt Link [ASA2] enabled at IRQ 21
pata_acpi 0000:00:0e.2: PCI INT C -> Link[ASA2] -> GSI 21 (level, low) -> IRQ 21
pata_acpi 0000:00:0e.2: setting latency timer to 64
pata_acpi 0000:00:0e.2: PCI INT C disabled
pata_amd 0000:00:0d.0: version 0.3.10
pata_amd 0000:00:0d.0: setting latency timer to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfc00 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfc08 irq 15
ata1.00: ATAPI: HL-DT-ST RW/DVD GCC-4480B, 1.00, max UDMA/33
ata1.01: ATA-6: ST380011A, 3.06, max UDMA/100
ata1.01: 156301488 sectors, multi 1: LBA48 
ata1: nv_mode_filter: 0x739f&0x701f->0x701f, BIOS=0x7000 (0xc0c60000) ACPI=0x701f (60:20:0x1f)
ata1: nv_mode_filter: 0x3f39f&0x3f01f->0x3f01f, BIOS=0x3f000 (0xc0c60000) ACPI=0x3f01f (60:20:0x1f)
ata1.00: configured for UDMA/33
ata1.01: configured for UDMA/100
ata2: port disabled. ignoring.
scsi 0:0:0:0: CD-ROM            HL-DT-ST RW/DVD GCC-4480B 1.00 PQ: 0 ANSI: 5
scsi 0:0:1:0: Direct-Access     ATA      ST380011A        3.06 PQ: 0 ANSI: 5
sata_nv 0000:00:0e.0: version 3.5
sata_nv 0000:00:0e.0: PCI INT A -> Link[APSI] -> GSI 23 (level, low) -> IRQ 23
sata_nv 0000:00:0e.0: Using SWNCQ mode
sata_nv 0000:00:0e.0: setting latency timer to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x9f0 ctl 0xbf0 bmdma 0xf700 irq 23
ata4: SATA max UDMA/133 cmd 0x970 ctl 0xb70 bmdma 0xf708 irq 23
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata3.00: native sectors (586072368) is smaller than sectors (625142448)
ata3.00: ATA-7: ST3320620AS, 3.AAD, max UDMA/133
ata3.00: 625142448 sectors, multi 1: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
ata4: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access     ATA      ST3320620AS      3.AA PQ: 0 ANSI: 5
sata_nv 0000:00:0e.1: PCI INT B -> Link[APSJ] -> GSI 22 (level, low) -> IRQ 22
sata_nv 0000:00:0e.1: Using SWNCQ mode
sata_nv 0000:00:0e.1: setting latency timer to 64
scsi4 : sata_nv
scsi5 : sata_nv
ata5: SATA max UDMA/133 cmd 0x9e0 ctl 0xbe0 bmdma 0xf200 irq 22
ata6: SATA max UDMA/133 cmd 0x960 ctl 0xb60 bmdma 0xf208 irq 22
ata5: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
sata_nv 0000:00:0e.2: PCI INT C -> Link[ASA2] -> GSI 21 (level, low) -> IRQ 21
sata_nv 0000:00:0e.2: Using SWNCQ mode
sata_nv 0000:00:0e.2: setting latency timer to 64
scsi6 : sata_nv
scsi7 : sata_nv
ata7: SATA max UDMA/133 cmd 0xf100 ctl 0xf000 bmdma 0xed00 irq 21
ata8: SATA max UDMA/133 cmd 0xef00 ctl 0xee00 bmdma 0xed08 irq 21
ata7: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata7.00: ATAPI: TSSTcorp CDDVDW SH-S203B, SB00, max UDMA/100
ata7.00: configured for UDMA/100
ata8: SATA link down (SStatus 0 SControl 300)
scsi 6:0:0:0: CD-ROM            TSSTcorp CDDVDW SH-S203B  SB00 PQ: 0 ANSI: 5
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
Driver 'sd' needs updating - please use bus_type methods
sd 0:0:1:0: [sda] 156301488 512-byte hardware sectors: (80.0 GB/74.5 GiB)
sd 0:0:1:0: [sda] Write Protect is off
sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:1:0: [sda] 156301488 512-byte hardware sectors: (80.0 GB/74.5 GiB)
sd 0:0:1:0: [sda] Write Protect is off
sd 0:0:1:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1
sd 0:0:1:0: [sda] Attached SCSI disk
sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb:<6>usbcore: registered new device driver usb
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 20
ehci_hcd 0000:00:0b.1: PCI INT B -> Link[APCL] -> GSI 20 (level, low) -> IRQ 20
ehci_hcd 0000:00:0b.1: setting latency timer to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0b.1: debug port 1
ehci_hcd 0000:00:0b.1: cache line size of 32 is not supported
ehci_hcd 0000:00:0b.1: irq 20, io mem 0xefffe000
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 23
ohci_hcd 0000:00:0b.0: PCI INT A -> Link[APCF] -> GSI 23 (level, low) -> IRQ 23
ohci_hcd 0000:00:0b.0: setting latency timer to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0b.0: irq 23, io mem 0xeffff000
 sdb1 sdb2 sdb3
Driver 'sr' needs updating - please use bus_type methods
sd 2:0:0:0: [sdb] Attached SCSI disk
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 10 ports detected
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
sr 6:0:0:0: Attached scsi CD-ROM sr1
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi8 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb 2-4: new full speed USB device using ohci_hcd and address 2
usb 2-4: configuration #1 chosen from 1 choice
hub 2-4:1.0: USB hub found
hub 2-4:1.0: 4 ports detected
usb 2-4.1: new low speed USB device using ohci_hcd and address 3
usb 2-4.1: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: G15 Gaming Keyboard as /class/input/input1
generic-usb 0003:046D:C226.0001: input,hidraw0: USB HID v1.10 Keyboard [G15 Gaming Keyboard] on usb-0000:00:0b.0-4.1/input0
input: G15 Gaming Keyboard as /class/input/input2
generic-usb 0003:046D:C226.0002: input,hiddev0,hidraw1: USB HID v1.10 Device [G15 Gaming Keyboard] on usb-0000:00:0b.0-4.1/input1
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
usb 2-4.3: new full speed USB device using ohci_hcd and address 4
usb 2-4.3: configuration #1 chosen from 1 choice
input: Logitech USB Gaming Mouse as /class/input/input3
generic-usb 0003:046D:C041.0003: input,hidraw2: USB HID v1.11 Mouse [Logitech USB Gaming Mouse] on usb-0000:00:0b.0-4.3/input0
generic-usb 0003:046D:C041.0004: hiddev1,hidraw3: USB HID v1.11 Device [Logitech USB Gaming Mouse] on usb-0000:00:0b.0-4.3/input1
usb 2-4.4: new full speed USB device using ohci_hcd and address 5
usb 2-4.4: configuration #1 chosen from 1 choice
input: G15 GamePanel LCD as /class/input/input4
generic-usb 0003:046D:C227.0005: input,hiddev2,hidraw4: USB HID v1.11 Keypad [G15 GamePanel LCD] on usb-0000:00:0b.0-4.4/input0
scsi 8:0:0:0: Direct-Access     ST350083 0AS                   PQ: 0 ANSI: 2
sd 8:0:0:0: [sdc] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 8:0:0:0: [sdc] Write Protect is off
sd 8:0:0:0: [sdc] Mode Sense: 38 00 00 00
sd 8:0:0:0: [sdc] Assuming drive cache: write through
sd 8:0:0:0: [sdc] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
sd 8:0:0:0: [sdc] Write Protect is off
sd 8:0:0:0: [sdc] Mode Sense: 38 00 00 00
sd 8:0:0:0: [sdc] Assuming drive cache: write through
 sdc: sdc1
sd 8:0:0:0: [sdc] Attached SCSI disk
usb-storage: device scan complete
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
rtc_cmos 00:05: RTC can wake from S4
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 242 bytes nvram, hpet irqs
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.61.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
forcedeth 0000:00:11.0: PCI INT A -> Link[APCH] -> GSI 22 (level, low) -> IRQ 22
forcedeth 0000:00:11.0: setting latency timer to 64
nv_probe: set workaround bit for reversed mac addr
forcedeth 0000:00:11.0: ifname eth0, PHY OUI 0x5043 @ 19, addr 00:1a:92:83:1d:8d
forcedeth 0000:00:11.0: highdma csum vlan pwrctl mgmt timirq gbit lnktim msi desc-v3
ACPI: PCI Interrupt Link [AMC1] enabled at IRQ 21
forcedeth 0000:00:12.0: PCI INT A -> Link[AMC1] -> GSI 21 (level, low) -> IRQ 21
forcedeth 0000:00:12.0: setting latency timer to 64
nv_probe: set workaround bit for reversed mac addr
forcedeth 0000:00:12.0: ifname eth1, PHY OUI 0x5043 @ 19, addr 00:1a:92:83:25:21
forcedeth 0000:00:12.0: highdma csum vlan pwrctl mgmt timirq gbit lnktim msi desc-v3
ACPI: PCI Interrupt Link [APC2] enabled at IRQ 17
C-Media PCI 0000:04:07.0: PCI INT A -> Link[APC2] -> GSI 17 (level, low) -> IRQ 17
input: Power Button (FF) as /class/input/input5
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input6
ACPI: Power Button (CM) [PWRB]
fan PNP0C0B:00: registered as cooling_device0
ACPI: Fan [FAN] (on)
processor ACPI_CPU:00: registered as cooling_device1
processor ACPI_CPU:01: registered as cooling_device2
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THRM] (40 C)
Linux agpgart interface v0.103
sr 0:0:0:0: Attached scsi generic sg0 type 5
sd 0:0:1:0: Attached scsi generic sg1 type 0
sd 2:0:0:0: Attached scsi generic sg2 type 0
sr 6:0:0:0: Attached scsi generic sg3 type 5
sd 8:0:0:0: Attached scsi generic sg4 type 0
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x1c00
ACPI: I/O resource nForce2_smbus [0x1c80-0x1cbf] conflicts with ACPI region SM01 [0x1c80-0x1c85]
ACPI: Device needs an ACPI driver
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x1c80
nvidia: module license 'NVIDIA' taints kernel.
input: PC Speaker as /class/input/input7
Error: Driver 'pcspkr' is already registered, aborting...
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ohci1394 0000:04:0b.0: PCI INT A -> Link[APC4] -> GSI 19 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19]  MMIO=[efbff000-efbff7ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
Error: Driver 'pcspkr' is already registered, aborting...
ACPI: PCI Interrupt Link [APC5] enabled at IRQ 16
nvidia 0000:01:00.0: PCI INT A -> Link[APC5] -> GSI 16 (level, low) -> IRQ 16
nvidia 0000:01:00.0: setting latency timer to 64
NVRM: loading NVIDIA UNIX x86 Kernel Module  180.22  Tue Jan  6 09:29:08 PST 2009
EXT3 FS on sdb2, internal journal
fuse init (API version 7.10)
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0011d800012b943c]
Adding 324272k swap on /dev/sdb3.  Priority:-1 extents:1 across:324272k
forcedeth 0000:00:11.0: irq 758 for MSI/MSI-X
eth0: no link during initialization.
forcedeth 0000:00:12.0: irq 757 for MSI/MSI-X
it87: Found IT8718F chip at 0x290, revision 2
it87: in3 is VCC (+5V)
it87: in7 is VCCH (+5V Stand-By)
coretemp coretemp.0: Using relative temperature scale!
coretemp coretemp.1: Using relative temperature scale!
input: G15 Extra Keys as /class/input/input8

ethtool

[sa@Feio ~]$ sudo ethtool eth0
Settings for eth0:
    Supported ports: [ MII ]
    Supported link modes:   10baseT/Half 10baseT/Full 
                            100baseT/Half 100baseT/Full 
                            1000baseT/Full 
    Supports auto-negotiation: Yes
    Advertised link modes:  10baseT/Half 10baseT/Full 
                            100baseT/Half 100baseT/Full 
                            1000baseT/Full 
    Advertised auto-negotiation: Yes
    Speed: Unknown! (65535)
    Duplex: Unknown! (255)
    Port: MII
    PHYAD: 19
    Transceiver: external
    Auto-negotiation: on
    Supports Wake-on: g
    Wake-on: d
    Link detected: no
[sa@Feio ~]$ sudo ethtool eth1
Settings for eth1:
    Supported ports: [ MII ]
    Supported link modes:   10baseT/Half 10baseT/Full 
                            100baseT/Half 100baseT/Full 
                            1000baseT/Full 
    Supports auto-negotiation: Yes
    Advertised link modes:  10baseT/Half 10baseT/Full 
                            100baseT/Half 100baseT/Full 
                            1000baseT/Full 
    Advertised auto-negotiation: Yes
    Speed: 100Mb/s
    Duplex: Full
    Port: MII
    PHYAD: 19
    Transceiver: external
    Auto-negotiation: on
    Supports Wake-on: g
    Wake-on: d
    Link detected: yes

hope you can help!

Offline

#15 2009-03-08 11:51:32

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

bumpz0r....


c'mon, no one can help? I mean, it's connecting to a network via wire, with dhcp, how many reasons for it not to work can there be?

pls try to help..

Offline

#16 2009-03-09 20:34:32

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

I just installed wicd and tried to connect using it, the network still times out...  I'm thinking maybe it's something to do with the driver?!? the interfaces appear with ifconfig but I can't find a reason for it not to work...

Offline

#17 2009-03-10 17:05:06

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

bump...


please help.... at least try... I have no idea what do next... It's so abnormal...

Offline

#18 2009-03-14 19:31:40

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

bump

Offline

#19 2009-03-15 13:42:33

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

did a full system upgrade problem still exists...

googled for the "no link during initialization" error and got no usable information...

Offline

#20 2009-03-16 09:32:27

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

"hello... anyone there?"

Offline

#21 2009-03-16 17:33:03

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

whatever... almost a whole fucking month talking to the walls and not being able to use my workstation... everyone is too good to TRY TO HELP solving this soooo very stupid problem...

.|.  FRAK ARCH COMMUNITY  .|.

come gentoo...

Mod edit - a certain word in this thread has been replaced to protect the innocent. tomk

Offline

#22 2009-03-16 22:00:08

quarkup
Member
From: Portugal
Registered: 2008-09-07
Posts: 497
Website

Re: [SOLVED]No wired network ?!?!?

1) you got a wiki.
2) learn how to use the manual.
3) ifconfig and iwconfig would do everything you need.


Hope (and glad) if I could help.

Last edited by quarkup (2009-03-16 22:14:19)

If people do not believe that mathematics is simple, it is only because they do not realize how complicated life is.
Simplicity is the ultimate sophistication.

Offline

#23 2009-03-17 16:34:48

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

i know that... i've read all that like a zillion times... i'm not new to arch even less to linux... and finding this BUG so abnormal is what's driving me crazy... it simply has no reason to exist...

btw, I'm sorry if i was childish before, which i believe i was, but the truth is that was what i was feeling, everybody thinks this is  just a rookie mistake, and it might be, but i've done everything there is to do..

as i said before i've decided to go back to gentoo, and i wont change that, but i will however use arch on my other 3 boxes, which are running fine btw, with wireless and wired static ip configurations...

thanks anyway...

Offline

#24 2009-03-17 16:41:05

rson451
Member
From: Annapolis, MD USA
Registered: 2007-04-15
Posts: 1,233
Website

Re: [SOLVED]No wired network ?!?!?

saz wrote:

c'mon, no one can help? I mean, it's connecting to a network via wire, with dhcp, how many reasons for it not to work can there be?

Let's see.  Apart from misconfiguration on some level, lack of a dhcp server, being out of dhcp addresses in the dhcp pool, a bad nic on the router/switch you are using, a bad ethernet cable (or using cat3 vs cat5 etc..), and a bad nic on the computer, I'm really not sure.  You are clearly getting online on some computer, so why don't you download and install the ethtool package as requested previously in this thread?  It seems you are asking for help but not helping yourself.  Not to mention your clearly fucking ridiculous bumps and replies to your own topic.

archlinux - please read this and this — twice — then ask questions.
--
http://rsontech.net | http://github.com/rson

Offline

#25 2009-03-17 21:09:57

saz
Member
From: Lisbon
Registered: 2008-04-19
Posts: 115

Re: [SOLVED]No wired network ?!?!?

rson451 wrote:
saz wrote:

c'mon, no one can help? I mean, it's connecting to a network via wire, with dhcp, how many reasons for it not to work can there be?

Let's see.  Apart from misconfiguration on some level, lack of a dhcp server, being out of dhcp addresses in the dhcp pool, a bad nic on the router/switch you are using, a bad ethernet cable (or using cat3 vs cat5 etc..), and a bad nic on the computer, I'm really not sure.  You are clearly getting online on some computer, so why don't you download and install the ethtool package as requested previously in this thread?  It seems you are asking for help but not helping yourself.  Not to mention your clearly fucking ridiculous bumps and replies to your own topic.

ridiculous is to answer a thread without reading it first.

Offline

Pages: 1 2

Topic closed

Board footer

Powered by FluxBB