You are not logged in.

#276 2007-03-01 00:07:27

ferlon
Member
Registered: 2007-02-28
Posts: 2

Re: 0.8 alpha/beta and final Voodoo installation feedback

Coasts of learning! More 46 hours in download, ok. I'll try.

Tks for your quick response, tpowa!

Offline

#277 2007-03-04 20:46:08

qlus
Member
From: Tychy, Poland
Registered: 2006-06-15
Posts: 74

Re: 0.8 alpha/beta and final Voodoo installation feedback

Installed base 0.8b2 on sata hdd. After install I've remooved old pata drive. This cause changing sata drive name from /dev/sdb to /dev/sda. (sis chipset)

In mkinitcpio.conf there are examples with ide, but images are made with pata.

Offline

#278 2007-03-05 11:54:21

mouse256
Member
From: Antwerpen, Belgium
Registered: 2005-08-24
Posts: 247

Re: 0.8 alpha/beta and final Voodoo installation feedback

I don't know if this problem is mentioned already, I don't have the time to read the whole thread...
But I had problems with ftp installation and a pc with 256mb memory, it crashes.  I seems the downloaded packages are hold somewhere in memory which causes an out-of-memory exception.  I think a better solution would be to put these packages in the tmp directory of the already mounted install drive at that point, it should keep a lot of extra memory available.

Offline

#279 2007-03-05 12:09:22

iBertus
Member
From: Greenville, NC
Registered: 2004-11-04
Posts: 2,228

Re: 0.8 alpha/beta and final Voodoo installation feedback

@mouse256: I thought the packages were downloaded into the normal cache in /mnt/var during installation. This should allow them to be kept for later use.

Offline

#280 2007-03-05 18:38:42

mienensuchkind
Member
Registered: 2007-01-21
Posts: 61

Re: 0.8 alpha/beta and final Voodoo installation feedback

installed the bata2 on my amd 64 3000+ on s-ata hd divices with s-ata dvd-device, (first time without any problems connected to these, thats why im mentioning big_smile )

no problems! thank you very much! ^^

Offline

#281 2007-03-06 10:03:10

baze
Member
Registered: 2005-10-30
Posts: 393

Re: 0.8 alpha/beta and final Voodoo installation feedback

i installed the beta2 on my thinkpad t60 and it worked without any problems. the only thing i noticed, was that while installing the packages i got some ouput from some packages which was printed and therefore screwed up the alignment a bit. this is more like a cosmetic issue. can't remember which package(s) caused that.

one suggestion though: when setting the mount points for the file system, the configured partitions are removed from the list. but what about when you accidently chose a wrong partition and want to change that?
my suggestions: don't remove configured partitions, but add something like [configured] to the partitions name. maybe in another color to make it obvious. this way you can see which partitions are already configured, but you could still select them, if you want to.

Last edited by baze (2007-03-06 19:54:57)

Offline

#282 2007-03-06 19:51:43

rieger
Member
From: Hilversum, The Netherlands
Registered: 2006-05-03
Posts: 18

Re: 0.8 alpha/beta and final Voodoo installation feedback

Installed Voodoo 0.8 on a Dell D820 and a Medion md8800, both without any problems.
Using ext2 as boot, XFS as / and ext3 as /home on both machines, ntfs-3g for accessing windows partitions, no problems, no kernel panics ;-)

Futhermore; on the Dell the ipw9345 works very well, and the fonts look very good (1680x1050). On the desktop (1280x1024) things look allright, but horrible in Firefox (not an Voodoo related problem i guess).

Anyway: to me this looks solid, cheers to the devs.

Offline

#283 2007-03-06 20:23:43

Lontronics
Member
Registered: 2006-08-28
Posts: 121

Re: 0.8 alpha/beta and final Voodoo installation feedback

Rieger, this sounds interesting.

I do have a Dell Inspiron 9400 and planned to install Arch on that laptop.
Till now I only did on a normal PC ('old Arch 0.7x)

But, I had some thoughts about finding out installation of my NVIDIA, ipw3945, soundcard etc... again.

How did you setup your ipw3945, and what are your recommendations?

I defenately will try to install Arch, also without help, but it is welcome ofcourse wink

Jan

Offline

#284 2007-03-06 21:51:19

rieger
Member
From: Hilversum, The Netherlands
Registered: 2006-05-03
Posts: 18

Re: 0.8 alpha/beta and final Voodoo installation feedback

ipw3945 installing is "pacman -S ipw3945".
add ipw3945d to rc.conf and you're done.
I've got an eth2 device which is the wireless one.
Only using I cannot get network profiles  to work, but a manual connect is not that big a problem for me.

For sound: just follow the ALSA setup from the Archwiki. I only have problems with the mic (for Skype), but i'll look into that later. (weird characters when looking at alsamixer from a console). Mp3's, video etc works fine however.

For nvidia: I did the base install, then xorg, then installed hwd, to autogenerate xorg.conf. Adjust the settings for resolution (just add 1680x1050 to your favourite colordepth) and you're done.
Then pacman nvidia, change "vesa"  to "nvidia" in xorg.xonf and uncomment the dri thingy in the end. startx should com up with the nvidia splash.
Oh, 1680x1050 resolution worked only after installing nvidia.

Offline

#285 2007-03-06 21:59:17

Lontronics
Member
Registered: 2006-08-28
Posts: 121

Re: 0.8 alpha/beta and final Voodoo installation feedback

Thanks Rieger, that's about the same I did at my Zenwalk installation for this laptop.

Almost ready to give it a try wink

Jan

Offline

#286 2007-03-07 07:34:21

.:B:.
Forum Fellow
Registered: 2006-11-26
Posts: 5,819
Website

Re: 0.8 alpha/beta and final Voodoo installation feedback

Don't be a chicken Lontronics tongue.


Got Leenucks? :: Arch: Power in simplicity :: Get Counted! Registered Linux User #392717 :: Blog thingy

Offline

#287 2007-03-07 07:46:20

vlado
Member
From: Tampere - Finland
Registered: 2005-03-20
Posts: 14

Re: 0.8 alpha/beta and final Voodoo installation feedback

Hi there,
one issue just for record.
I tried to install arch from CD onto single partition (/dev/sda2 was / and there was no sepparate /boot partition, plus swap).
After install, boot went nicely through, till it said EXT3 fs mounting root read only,
which was followed by sh: root=/dev/sda2 can not be found or similar message. Notice, it was right after sda2 was mounted with correct filesystem.
Only fix I could figure out was to reinstall and create some separate boot partttion.

Offline

#288 2007-03-07 09:58:58

blipblop
Member
Registered: 2007-03-07
Posts: 2

Re: 0.8 alpha/beta and final Voodoo installation feedback

Successfuly installed on sata drive, msi k9vgm-v motherboard, dualcore amd3600+.
When formatting the partitions with xfs I could not install packages, but changing to ext2 it worked just fine.
When installing with ext3, I get segmentation fault when installing the kernel and the system restarts.
I am happy for this release, I needed a distribution with kernel 2.6.19+ to support the vt8237a chipset in my motherboard. Thanks a lot! big_smile
/New archlinux user

edit:
I got ext3 working fine too. It was probably due to me not being familiar with the archlinux installer, or incorrect bios-settings!

Last edited by blipblop (2007-03-08 13:39:22)

Offline

#289 2007-03-10 22:53:50

linfan
Member
From: Stockholm, Sweden
Registered: 2004-04-23
Posts: 135

Re: 0.8 alpha/beta and final Voodoo installation feedback

installed 32 bit on my 64 amd yesterday with the 0.8 beta ftp iso - all went well but it could not find my ide dvd-burner. It made it into a scsi device sr0. Had to install the gimmick 0.7.2 and upgrade that way.

But it made a nice grub with two images and it added the keyboard layouts to rc.conf.

Regards,

linfan

Offline

#290 2007-03-20 23:48:17

Lontronics
Member
Registered: 2006-08-28
Posts: 121

Re: 0.8 alpha/beta and final Voodoo installation feedback

Okay, today was THE day.

Last week I tried to install Arch on my Dell Inspiron 9400 laptop without success...
My own fault because I did not write things down, did not read the Wiki...

After some printing, some reading and some searching, this evening I tried it again.
And now I am typing from my fresh Arch install; Base, a small X setup and Opera at the moment.

Wow, bloody fast!!

At this moment updating with pacman, and tomorrow I will try to install the rest.

Seems very promising.

Jan

Last edited by Lontronics (2007-03-21 07:54:56)

Offline

#291 2007-03-21 08:35:32

oli
Member
From: 127.0.0.1
Registered: 2006-02-07
Posts: 164
Website

Re: 0.8 alpha/beta and final Voodoo installation feedback

Installed 0.8 beta 2 without any hassle.

Pentium 640, 1G memory, Asus P5P800 (i865), Nvidia Geforce 6600 graphics card, two ATA harddrives, DVD-ROM and DVD burner, no dualboot, dualview

Good work smile


Use UNIX or die.

Offline

#292 2007-03-22 12:37:11

feralert
Member
Registered: 2007-03-21
Posts: 12

Re: 0.8 alpha/beta and final Voodoo installation feedback

Hi people!

I'm trying to install 0.8 b2 on a Dell latitute (p3 500, 512 ram) but all i get is a kernel panic.

I have opened this topic in the Instalation forum asking for help but as this is for feedback i wanted to let you know here too.

I have also installed archlinux on a desktop pII 400 with no problems but for that i used the 0.72 release (that was before i found this thread and the 0.8 isos) and its working flawlessly.

Outstanding distro!

Offline

#293 2007-03-22 15:59:29

wizzard
Member
From: PA, US
Registered: 2006-10-17
Posts: 33

Re: 0.8 alpha/beta and final Voodoo installation feedback

installed arch 0.8b2 on my acer aspire 5672wmli and everything went great, not a single problem here. I had problems later when the wxGTK 2.8 update killed codeblocks so I had to downgrade to 2.6 but aside from that best distro evar

Offline

#294 2007-03-26 13:38:09

cr7
Member
Registered: 2006-11-28
Posts: 103

Re: 0.8 alpha/beta and final Voodoo installation feedback

0.8beta2 works perfectly in all my machines! smile

Offline

#295 2007-03-31 11:46:08

tpowa
Developer
From: Lauingen , Germany
Registered: 2004-04-05
Posts: 2,322

Re: 0.8 alpha/beta and final Voodoo installation feedback

Hi Archlinux Community,
31th March, 14:00 CEST (Central European Summer Time)
it's done final 0.8 Voodoo ISOs for i686 and x86_64 are ready smile

Get Archlinux ISOs in /0.8/iso/{i686,x86_64} on your favorite mirror.
http://wiki.archlinux.org/index.php/Mirrors
or
http://www.archlinux.org/download/
Please don't forget to check md5sums.

Torrents are already up and seeded.
Metalink packages will be prepared soon.

Changelog of ISO (compared to 0.7.2 install iso):
- to boot the ISO 96 MB RAM are recommended,
  it breaks somewhere between 80 - 90 MB RAM.
  (calculated like this: kernel image + initrd size + decompressed initrd)
- dropped install floppy support
- switched from busybox to archboot usage
- Updated packages (including linux 2.6.20.4)
- Full mkinitcpio support
- Installation on PATA and IDE possible (PATA is default now)
  ide-legacy option included for old IDE subsystem
- All parameters initcpio understands, new ISO does understand
- Usb devices (keyboards/cd/dvd) should now work as they should
- Usage of hwdetect/udev autodetection during boot
- added memtest86+ to iso
- added installation support on cciss devices
- pacman is included to allow installation of any other needed package
  in install environment.
- added /etc/rc.d/ and /etc/rc.conf support
- added arch network support, including ssh,telnet and portmap services
- added vpn support
- added framebuffer modules to install environment
- added cpufreq support
- added iptables support
- added grub and lilo to install environment
- custom config files support:
  any media with /config directory and files will be copied to /etc/
  install environment
- loading packages as addons during boot:
  any media with /packages directory including pacman packages will be
  installed during bootup.
- links and naim included to be able to communicate over the internet.
- added kexec support


Changelog of new setup (compared to 0.7.2 setup)
- added some information dialogs
- added some confirmation dialogs
- added set root password
- removed all kernel24 stuff
- switched to initcpio only support
- added locale-gen file for editing
- only show devices that are usefull in mountpoints selection,
  partitioning and network
- possibility to select dm and md devices from setup
  (creation of lvm and md still needs to be done by hand!)
- mkinitcpio autoconfiguration. This includes HOOKS autoconfiguration
  and hostcontroller configuration: ide/scsi/sata modules are put into
  MODULES= in mkinitcpio.conf to ensure right loading order and avoid
  device-swapping
- network modules are put in the MODULES=() in rc.conf - again, this is
  done to avoid random swapping of multiple network interfaces
- added http:// net install support

Bug collector of fixed showstoppers is here:
http://bugs.archlinux.org/task/6031

I would like to thank you all, who assisted in testing
and of course finding/fixing bugs, you users/devs simply rock.

Happy installing and have fun.

greetings
tpowa

Offline

#296 2007-03-31 12:06:16

scarney
Member
From: Wisconsin, US
Registered: 2006-07-11
Posts: 173

Re: 0.8 alpha/beta and final Voodoo installation feedback

downloading and seeding now! 8)

edit: w00t! wink

Last edited by scarney (2007-03-31 12:19:39)

Offline

#297 2007-03-31 12:58:21

meulok
Member
Registered: 2007-03-31
Posts: 2

Re: 0.8 alpha/beta and final Voodoo installation feedback

Is there any body who know where the 0.8 voodoo installation guide is?

Offline

#298 2007-03-31 13:19:54

tpowa
Developer
From: Lauingen , Germany
Registered: 2004-04-05
Posts: 2,322

Re: 0.8 alpha/beta and final Voodoo installation feedback

on CD is an updated guide

Offline

#299 2007-03-31 13:30:45

paulr
Member
Registered: 2007-03-23
Posts: 52

Re: 0.8 alpha/beta and final Voodoo installation feedback

Installed from 0.8 yesterday ; no problems, went like clockwork. Criticisms ...... errr ...... well the confirmation before formatting partitions screen is a little difficult to read smile

Does some nice things 0.7.2 didn't, like putting my r8169 module into /etc/rc.conf automatically.

As regards documentation, if you can install 0.7.2, you can install this ; it is (on the surface) a very similar process. The main difference I recall is when you go into Configure System you are asked a barrage of questions (defaults all okay) before you can edit the config files.

Thanks guys ; this distro is brilliant. As an Archer (sic?) of about a week I keep thinking there has to be a downside to it - just haven't found one yet smile Doesn't have the downsides of gentoo (36 hour install) or ubuntu (36 hours to do anything ;-) )

Ah, I have thought of a problem. It doesn't automagically load the cx88-dvb module that my NOVA DVB-T card requires. I have to put it in /etc/rc.conf myself (exhausting work ....)

Offline

#300 2007-03-31 15:53:35

madhatter
Member
From: Freudenstadt, Germany
Registered: 2004-09-01
Posts: 59

Re: 0.8 alpha/beta and final Voodoo installation feedback

Good thing it wasn't released one day later, wouldn't believe it then wink
Anyway I can't find the link to the torrents (only the 0.7.2 ISOs are available at the download page)

Offline

Board footer

Powered by FluxBB