You are not logged in.

#1 2008-04-06 10:49:15

billytcf
Member
From: Hong Kong
Registered: 2008-04-06
Posts: 12

[SOLVED]dhcpcd err, eth0:timed out

Hello,

I installed eveyrthing according to the beginner's guide, then

got into some problems when connect to my router. Here are something I got

err, eth0: timed out
warn, eth0: using IP$LL address 169.254.122.53

I have made sure the router at it's default settings
all wires connected well
indeed the router shows the wires are fine
WinXP can also connect well

Heard from other that it may be prob with Realtek driver, but for my ethernet no driver can be found on realtek's web (it's integrated into kernel)
I 'm wondering are there something wrong within??

Thanks for your help!!

dhcpcd-d

info, eth0: dhcpcd 3.2.1 starting
info, eth0: hardware address = 00:0c:76:e1:26:8c
info, eth0: broadcasting for a lease
debug, eth0: sending DHCP_DISCOVER with xid 0x19e6ced5
debug, eth0: waiting on select for 20 seconds
debug, eth0: sending DHCP_DISCOVER with xid 0x19e6ced5
debug, eth0: sending DHCP_DISCOVER with xid 0x19e6ced5
debug, eth0: sending DHCP_DISCOVER with xid 0x19e6ced5
debug, eth0: sending DHCP_DISCOVER with xid 0x19e6ced5
debug, eth0: sending DHCP_DISCOVER with xid 0x19e6ced5
debug, eth0: sending DHCP_DISCOVER with xid 0x19e6ced5
info, eth0: trying to use old lease in `/var/lib/dhcpcd/dhcpcd-eth0.info'
debug, eth0: sending ARP probe #1
debug, eth0: sending ARP probe #2
debug, eth0: sending ARP probe #3
debug, eth0: sending ARP claim #1
debug, eth0: sending ARP claim #2
info, eth0: adding IP address 169.254.122.53/16
debug, eth0: no dns information to write
debug, eth0: forking to background

ifconfig

eth0      Link encap:Ethernet  HWaddr 00:0C:76:E1:26:8C  
          inet addr:169.254.122.53  Bcast:169.254.255.255  Mask:255.255.0.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:19 Base address:0xa000 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

lsmod

Module                  Size  Used by
nls_cp437               5888  1 
vfat                   10752  1 
fat                    46876  1 vfat
usb_storage            83648  1 
xfs                   566280  1 
parport_pc             35300  1 
firewire_ohci          16000  0 
firewire_core          36800  1 firewire_ohci
crc_itu_t               2304  1 firewire_core
ohci1394               28976  0 
ieee1394               81464  1 ohci1394
ppdev                   7556  0 
lp                      9220  0 
parport                31560  3 parport_pc,ppdev,lp
ppp_generic            24596  0 
i2c_i801                8848  0 
shpchp                 29716  0 
pci_hotplug            26272  1 shpchp
usbhid                 42560  0 
hid                    38272  1 usbhid
ff_memless              5128  1 usbhid
i2c_i810                4612  0 
i2c_algo_bit            6020  1 i2c_i810
i2c_core               19584  3 i2c_i801,i2c_i810,i2c_algo_bit
intel_agp              22164  1 
agpgart                28120  1 intel_agp
sg                     26896  0 
thermal                12956  0 
evdev                   9344  0 
processor              29144  1 thermal
fan                     3844  0 
button                  6544  0 
battery                10756  0 
ac                      4612  0 
snd_seq_oss            30336  0 
snd_seq_midi_event      6656  1 snd_seq_oss
snd_intel8x0           29084  0 
snd_seq                48464  4 snd_seq_oss,snd_seq_midi_event
snd_seq_device          6796  2 snd_seq_oss,snd_seq
snd_ac97_codec         97828  1 snd_intel8x0
snd_pcm_oss            38432  0 
snd_pcm                70404  3 snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer              19588  2 snd_seq,snd_pcm
snd_page_alloc          8072  2 snd_intel8x0,snd_pcm
snd_mixer_oss          14848  1 snd_pcm_oss
snd                    46436  9 snd_seq_oss,snd_intel8x0,snd_seq,snd_seq_device,snd_ac97_codec,snd_pcm_oss,snd_pcm,snd_timer,snd_mixer_oss
soundcore               6496  1 snd
ac97_bus                2304  1 snd_ac97_codec
slhc                    6016  1 ppp_generic
8139too                22912  0 
8139cp                 19840  0 
mii                     4992  2 8139too,8139cp
rtc_cmos                7712  0 
rtc_core               15752  1 rtc_cmos
rtc_lib                 3072  1 rtc_core
ext3                  124040  1 
jbd                    44308  1 ext3
mbcache                 7168  1 ext3
sr_mod                 15268  0 
cdrom                  34080  1 sr_mod
sd_mod                 23168  6 
ehci_hcd               33804  0 
uhci_hcd               23312  0 
usbcore               128620  5 usb_storage,usbhid,ehci_hcd,uhci_hcd
ata_piix               14852  3 
ata_generic             5380  0 
pata_acpi               5248  0 
libata                141424  3 ata_piix,ata_generic,pata_acpi

lspci

00:00.0 Host bridge: Intel Corporation 82845G/GL[Brookdale-G]/GE/PE DRAM Controller/Host-Hub Interface (rev 03)
00:02.0 VGA compatible controller: Intel Corporation 82845G/GL[Brookdale-G]/GE Chipset Integrated Graphics Device (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 82)
00:1f.0 ISA bridge: Intel Corporation 82801DB/DBL (ICH4/ICH4-L) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801DB (ICH4) IDE Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 02)
01:0a.0 Communication controller: Conexant HSF 56k HSFi Modem (rev 01)
01:0c.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
01:0d.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80)

dmesg

Linux version 2.6.24-ARCH (root@artin) (gcc version 4.3.0 (GCC) ) #1 SMP PREEMPT Sun Mar 30 11:40:06 CEST 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000f7f0000 (usable)
 BIOS-e820: 000000000f7f0000 - 000000000f7f3000 (ACPI NVS)
 BIOS-e820: 000000000f7f3000 - 000000000f800000 (ACPI data)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
247MB LOWMEM available.
found SMP MP-table at 000f5ea0
Entering add_active_range(0, 0, 63472) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->    63472
  HighMem     63472 ->    63472
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->    63472
On node 0 totalpages: 63472
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 463 pages used for memmap
  Normal zone: 58913 pages, LIFO batch:15
  HighMem zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
DMI 2.3 present.
ACPI: RSDP 000F7D40, F7F3000 (r2 IntelR)
ACPI Warning (tbutils-0453): BIOS XSDT has NULL entry, using RSDT [20070126]
ACPI: RSDT 0F7F3000, 002C (r1 IntelR AWRDACPI 30302E32 AWRD        1)
ACPI: FACP 0F7F3040, 0084 (r2 IntelR AWRDACPI 30302E32 AWRD        1)
ACPI: DSDT 0F7F3100, 3971 (r1 INTELR AWRDACPI     1000 MSFT  100000D)
ACPI: FACS 0F7F0000, 0040
ACPI: APIC 0F7F6A80, 0068 (r1 IntelR AWRDACPI 30302E32 AWRD        1)
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 10000000 (gap: 0f800000:ef400000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 62977
Kernel command line: root=/dev/sdb1 ro vga=791
mapped APIC to ffffb000 (fee00000)
mapped IOAPIC to ffffa000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Detected 2600.120 MHz processor.
Console: colour dummy device 80x25
console [tty0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 245448k/253888k available (2589k kernel code, 7820k reserved, 845k data, 292k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfff80000 - 0xfffff000   ( 508 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xd0000000 - 0xff7fe000   ( 759 MB)
    lowmem  : 0xc0000000 - 0xcf7f0000   ( 247 MB)
      .init : 0xc0461000 - 0xc04aa000   ( 292 kB)
      .data : 0xc03876ea - 0xc045acdc   ( 845 kB)
      .text : 0xc0100000 - 0xc03876ea   (2589 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=11, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 5205.23 BogoMIPS (lpj=8672378)
Security Framework initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: bfebfbff 00000000 00000000 0000b080 00004400 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
Early unpacking initramfs... done
ACPI: Core revision 20070126
ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found.
CPU0: Intel(R) Celeron(R) CPU 2.60GHz stepping 09
Total of 1 processors activated (5205.23 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
Brought up 1 CPUs
net_namespace: 64 bytes
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb970, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
* The chipset may have PM-Timer Bug. Due to workarounds for a bug,
* this clock source is slow. If you are sure your timer does not have
* this bug, please use "acpi_pm_good" to disable the workaround
PCI quirk: region 0400-047f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0480-04bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
system 00:01: ioport range 0xb78-0xb7b has been reserved
system 00:01: ioport range 0xf78-0xf7b has been reserved
system 00:01: ioport range 0xa78-0xa7b has been reserved
system 00:01: ioport range 0xe78-0xe7b has been reserved
system 00:01: ioport range 0xbbc-0xbbf has been reserved
system 00:01: ioport range 0xfbc-0xfbf has been reserved
system 00:01: ioport range 0x4d0-0x4d1 has been reserved
system 00:01: ioport range 0x294-0x297 has been reserved
system 00:0a: ioport range 0x400-0x4bf could not be reserved
PCI: Bridge: 0000:00:1e.0
  IO window: c000-cfff
  MEM window: ec000000-edffffff
  PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs... it is
Freeing initrd memory: 922k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:02.0
vesafb: framebuffer at 0xe0000000, mapped to 0xd0080000, using 3072k, total 8000k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
Switched to high resolution mode on CPU 0
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:07: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
cpuidle: using governor ladder
cpuidle: using governor menu
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
Using IPI No-Shortcut mode
Freeing unused kernel memory: 292k freed
libata version 3.00 loaded.
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.1 to 64
ACPI: PCI interrupt for device 0000:00:1f.1 disabled
ata_piix 0000:00:1f.1: version 2.12
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xf000 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xf008 irq 15
ata1.00: ATA-4: ST320414A, 3.28, max UDMA/100
ata1.00: 39102336 sectors, multi 16: LBA 
ata1.00: configured for UDMA/100
ata2.00: ATAPI: LITE-ON COMBO SOHC-4832K, OPK3, max UDMA/33
ata2.01: ATA-3: ST36451A, 840488, max UDMA/33
ata2.01: 12594960 sectors, multi 16: LBA 
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
ata2: EH complete
scsi 0:0:0:0: Direct-Access     ATA      ST320414A        3.28 PQ: 0 ANSI: 5
scsi 1:0:0:0: CD-ROM            LITE-ON  COMBO SOHC-4832K OPK3 PQ: 0 ANSI: 5
scsi 1:0:1:0: Direct-Access     ATA      ST36451A         8404 PQ: 0 ANSI: 5
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 17, io base 0x0000d800
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Driver 'sd' needs updating - please use bus_type methods
ACPI: PCI Interrupt 0000:00:1d.1[b] -> GSI 19 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
Driver 'sr' needs updating - please use bus_type methods
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 18, io base 0x0000d000
sd 0:0:0:0: [sda] 39102336 512-byte hardware sectors (20020 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 39102336 512-byte hardware sectors (20020 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
sd 0:0:0:0: [sda] Attached SCSI disk
sr0: scsi3-mmc drive: 0x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sd 1:0:1:0: [sdb] 12594960 512-byte hardware sectors (6449 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:1:0: [sdb] 12594960 512-byte hardware sectors (6449 MB)
sd 1:0:1:0: [sdb] Write Protect is off
sd 1:0:1:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:1:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1 sdb2 sdb3
sr 1:0:0:0: Attached scsi CD-ROM sr0
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 16, io base 0x0000d400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
sd 1:0:1:0: [sdb] Attached SCSI disk
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xee080000
usb 2-2: new low speed USB device using uhci_hcd and address 2
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 6 ports detected
usb 2-2: new low speed USB device using uhci_hcd and address 3
usb 2-2: configuration #1 chosen from 1 choice
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
8139cp 0000:01:0c.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:01:0c.0: Try the "8139too" driver instead.
8139too Fast Ethernet driver 0.9.28
ACPI: PCI Interrupt 0000:01:0c.0[A] -> GSI 23 (level, low) -> IRQ 19
eth0: RealTek RTL8139 at 0xd002a000, 00:0c:76:e1:26:8c, IRQ 19
eth0:  Identified 8139 chip type 'RTL-8101'
ACPI: PCI Interrupt 0000:00:1f.5[b] -> GSI 17 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1f.5 to 64
intel8x0_measure_ac97_clock: measured 52831 usecs
intel8x0: clocking to 48000
input: Power Button (FF) as /devices/virtual/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/virtual/input/input3
ACPI: Power Button (CM) [PWRB]
ACPI Exception (processor_core-0816): AE_NOT_FOUND, Processor Device is not present [20070126]
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
sd 1:0:1:0: Attached scsi generic sg2 type 0
Linux agpgart interface v0.102
agpgart: Detected an Intel 830M Chipset.
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xe0000000
i810_smbus 0000:00:02.0: i810/i815 i2c device found.
usbcore: registered new interface driver hiddev
input: HID 062a:0000 as /devices/pci0000:00/0000:00:1d.1/usb2/2-2/2-2:1.0/input/input4
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
intel_rng: FWH not detected
input,hidraw0: USB HID v1.10 Mouse [HID 062a:0000] on usb-0000:00:1d.1-2
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:1f.3[b] -> GSI 17 (level, low) -> IRQ 20
PPP generic driver version 2.4.2
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
ACPI: PCI Interrupt 0000:01:0d.0[A] -> GSI 23 (level, low) -> IRQ 19
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[19]  MMIO=[ed011000-ed0117ff]  Max Packet=[2048]  IR/IT contexts=[4/8]
parport_pc 00:08: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0010dc00006066f1]
EXT3 FS on sdb1, internal journal
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem sdb2
Ending clean XFS mount for filesystem: sdb2
Adding 979956k swap on /dev/sdb3.  Priority:-1 extents:1 across:979956k
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 0008203c.
eth0:  Tx descriptor 3 is 0008203c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 0008203c. (queue head)
eth0:  Tx descriptor 1 is 0008203c.
eth0:  Tx descriptor 2 is 0008203c.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 0008203c.
eth0:  Tx descriptor 2 is 0008203c.
eth0:  Tx descriptor 3 is 0008203c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 0008203c. (queue head)
eth0:  Tx descriptor 1 is 0008203c.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 0008203c. (queue head)
eth0:  Tx descriptor 1 is 0008203c.
eth0:  Tx descriptor 2 is 0008203c.
eth0:  Tx descriptor 3 is 0008203c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 0008203c. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
usb 4-5: new high speed USB device using ehci_hcd and address 3
usb 4-5: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi2 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 0008203c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
scsi 2:0:0:0: Direct-Access     Multi    Flash Reader     1.00 PQ: 0 ANSI: 0
sd 2:0:0:0: [sdc] 4022272 512-byte hardware sectors (2059 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 03 00 00 00
sd 2:0:0:0: [sdc] Assuming drive cache: write through
sd 2:0:0:0: [sdc] 4022272 512-byte hardware sectors (2059 MB)
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 03 00 00 00
sd 2:0:0:0: [sdc] Assuming drive cache: write through
 sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg3 type 0
usb-storage: device scan complete
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 0008203c. (queue head)
eth0:  Tx descriptor 1 is 0008203c.
eth0:  Tx descriptor 2 is 0008203c.
eth0:  Tx descriptor 3 is 0008203c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 00082156.
eth0:  Tx descriptor 3 is 00082156.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
NETDEV WATCHDOG: eth0: transmit timed out
eth0: Transmit timeout, status 0d 0000 c07f media 10.
eth0: Tx queue start entry 4  dirty entry 0.
eth0:  Tx descriptor 0 is 00082156. (queue head)
eth0:  Tx descriptor 1 is 00082156.
eth0:  Tx descriptor 2 is 0008203c.
eth0:  Tx descriptor 3 is 0008203c.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

Last edited by billytcf (2008-04-24 14:11:44)


Billy Tse

Offline

#2 2008-04-08 07:50:01

kinection
Member
Registered: 2008-04-08
Posts: 12

Re: [SOLVED]dhcpcd err, eth0:timed out

You sure you only have one eth device?

ifconfig -a

Try this, install ethtool and run it:
  ethtool eth0
See if "Link detected:" is yes or no. If no, then it means you aren't plugged in, wire is bad, or something similar.

What is your subnet? 192.168.x.x? I'll assume it's 192.168.0.x.
Try just forcing your card to an ip on your subnet. E.g.: ifconfig eth0 192.168.0.123
Then,  try pinging your router. (most likely 192.168.0.1, so `ping 192.168.0.1`)

If it is a driver issue, it should have failed by this point.


~kinection

Offline

#3 2008-04-08 09:39:36

billytcf
Member
From: Hong Kong
Registered: 2008-04-06
Posts: 12

Re: [SOLVED]dhcpcd err, eth0:timed out

thank you kinection.

I'll try that.

Guess I gotta force ip -.-""


Billy Tse

Offline

#4 2008-04-24 14:11:21

billytcf
Member
From: Hong Kong
Registered: 2008-04-06
Posts: 12

Re: [SOLVED]dhcpcd err, eth0:timed out

problem solved!!! it's the realtek prob, found the solution in archwiki

thanks everybody for concern!


Billy Tse

Offline

#5 2008-07-29 03:52:29

luuuciano
Member
Registered: 2007-01-27
Posts: 310

Re: [SOLVED]dhcpcd err, eth0:timed out

hey man, and why do not you post an url or maybe keywords to find the solution in the wiki?


I arch, you arch, he arch, she arch, we arch, they arch...

Offline

Board footer

Powered by FluxBB