Auto-mounting USB storage devices doesn't work

I am Gianluca · 2011-06-17 18:50:48

Hi all,
I have some problems with the auto-mounting of USB storage devices. I already installed udisks and ntfs-3g.
When I connect the external device (it's an external hard disk WD My Passport 500GB, but I have the same problem with a SanDisk USB stick 8GB) the auto-mount doesn't work. I see a shorcut in the left panel of Thunar but if I try to use it Thunar crash without any message error.
I try with the manual mount and it works, but the left panel of Thunar continue to have the same problem.

In the italian Arch forum a friend suggest me to open Thunar from bash and close it. If I do it I receive this error log:

$ thunar
thunar: symbol lookup error: /usr/lib/libstdc++.so.6: undefined symbol: _ZNSt14error_categoryD2Ev, version GLIBCXX_3.4.15

and this is the reply of dmesg command:

[  340.826768] usb 1-1: new high speed USB device number 2 using ehci_hcd
[  341.591397] Initializing USB Mass Storage driver...
[  341.592166] scsi6 : usb-storage 1-1:1.0
[  341.592345] usbcore: registered new interface driver usb-storage
[  341.592349] USB Mass Storage support registered.
[  341.599805] usbcore: registered new interface driver uas
[  342.591094] scsi 6:0:0:0: Direct-Access     WD       My Passport 070A 1032 PQ: 0 ANSI: 4
[  342.591474] sd 6:0:0:0: Attached scsi generic sg1 type 0
[  342.592845] scsi 6:0:0:1: CD-ROM            WD       Virtual CD 070A  1032 PQ: 0 ANSI: 4
[  342.593048] scsi 6:0:0:1: Attached scsi generic sg2 type 5
[  342.594050] sd 6:0:0:0: [sdb] 975400960 512-byte logical blocks: (499 GB/465 GiB)
[  342.594814] scsi 6:0:0:2: Enclosure         WD       SES Device       1032 PQ: 0 ANSI: 4
[  342.595141] scsi 6:0:0:2: Attached scsi generic sg3 type 13
[  342.596546] sd 6:0:0:0: [sdb] Write Protect is off
[  342.596553] sd 6:0:0:0: [sdb] Mode Sense: 23 00 10 00
[  342.596557] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  342.599163] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  342.618228]  sdb: sdb1
[  342.621039] sd 6:0:0:0: [sdb] Assuming drive cache: write through
[  342.621046] sd 6:0:0:0: [sdb] Attached SCSI disk
[  342.665174] sr0: scsi3-mmc drive: 51x/51x caddy
[  342.665180] cdrom: Uniform CD-ROM driver Revision: 3.20
[  342.665447] sr 6:0:0:1: Attached scsi CD-ROM sr0
[  342.665654] ses 6:0:0:2: Attached Enclosure device
[  349.105348] [b]Thunar[996]: segfault at 0 ip b6de1660 sp bfe586f4 error 4 in libglib-2.0.so.0.2800.8[b6d6f000+ed000][/b]

Do you have any suggestion?
Thank you very much,

Gianluca

I am Gianluca · 2011-06-20 16:05:11

Any idea?

Varg · 2011-06-20 16:51:40

Do you have gvfs installed ?Thunar needs it to auto-mount.
Costum udev rules also conflict with thunar.

Durden · 2011-06-20 17:39:55

Does this help? https://wiki.archlinux.org/index.php/Autofs

Inxsible · 2011-06-20 18:52:14

udisks and helper scripts like devmon and udiskie is also another option if for some reason you do not want gvfs.

Mr.Elendig · 2011-06-20 19:15:43

Are you using [testing]? Partially updated system?
The error looks like you have a different version of gcc-libs / glibc than the app was built against.

Last edited by Mr.Elendig (2011-06-20 19:16:33)

Arch Linux

#1 2011-06-17 18:50:48

Auto-mounting USB storage devices doesn't work

#2 2011-06-20 16:05:11

Re: Auto-mounting USB storage devices doesn't work

#3 2011-06-20 16:51:40

Re: Auto-mounting USB storage devices doesn't work

#4 2011-06-20 17:39:55

Re: Auto-mounting USB storage devices doesn't work

#5 2011-06-20 18:52:14

Re: Auto-mounting USB storage devices doesn't work

#6 2011-06-20 19:15:43

Re: Auto-mounting USB storage devices doesn't work

Board footer